buttons LINCOLN MKZ 2013 Quick Reference Guide

3 SeRviCe engine
Soon Light
illuminates briefly when the ignition
is turned on. if it remains on or is blinking
after the engine is started, the on-board
diagnostics system ( obD-ii) has detected
a malfunction. Drive in a moderate
fashion and contact your authorized
dealer as soon as possible.
4 PoweR tiLt/
teLeSC oPing
SteeRing CoL umn*
Your power tilt steering column has a
four-way rocker control that allows you
to adjust the steering wheel to your
desired position.
5 SteeRing wheeL
Audio ContRoLS*
Press VOL + or VOL - to increase or
decrease volume levels.
Press
to access the next/
previous radio station preset, CD
track or preset satellite radio channel*.
Press
to access voice recognition.
Press
to access SYnC®
phone features.
6 Right vehiCLe
inF oRmA tion diSPLA y
Displays information about
entertainment, Phone, navigation*
and Climate. Use the right, 5-way
control located on your steering wheel
to scroll through, highlight and make
minor adjustments within a selected
menu. Refer to the MyLincoln Touch™
chapter in your Owner’s Manual for
more information.

7 PuSh Button St ARt
You can start your vehicle while your
keys remain in your pocket, purse
or back pack. With your vehicle in P
(Park), fully press the brake pedal and
press the ENGINE START STOP button.
Press the button again to turn the
engine off.
Note: Your intelligent access key must
be inside the vehicle for the ignition
to start.
8 PuSh Button
ShiFt tRAnSmiSSion
Your vehicle is equipped with an
electronic transmission. The shift buttons
are located on the center stack next the
MyLincoln Touch™ system.
Putting your vehicle in gear:
1. Fully press down the brake pedal.
2. Press and release one of the PRNDS
buttons to select your gear.
3. The gear shift button you select will
illuminate and the instrument cluster
will show a telltale of the selected gear.
4. Release the brake pedal and your
transmission will remain in the
selected gear.
Note: When entering an automatic car
wash, always put your vehicle into Stay
in Neutral mode. To put your vehicle in
Stay in Neutral mode, make sure your
vehicle is stationary first, and then:
1. Press the N (neutral) button on the
shifter assembly once. The information
display screen will read “Press N to
enter Stay in Neutral mode”.
2. Press N on the shifter assembly
again. The message “Stay in Neutral
mode engaged” will appear in the
instrument cluster and the n button
will flash continuously to confirm
your selection.
3. To exit Stay in Neutral, select another gear.
1 LeFt vehiCLe
inF oRmA tion diSPLA y
Provides information about various
systems on your vehicle. Use the left,
5-way control located on the steering
wheel to choose and confirm settings
and messages. Refer to the Information
Displays chapter in your Owner’s Manual
for more information.
2 AdAPtive
CRuiSe ContRoL *
Automatically adjusts your speed to
maintain a set distance between you
and the vehicle in front of you in the
same lane. You can set the gap distance
between yourself and the vehicle in front
by pressing the
and buttons on the
steering wheel.
Note: Driving aids do not replace the
need to watch where the vehicle is
moving and brake where necessary.
Refer to your the Cruise Control chapter
of your Owner’s Manual for safety
information, more detail and limitations.
5
1
1
4
3
2
8
5
7
6
inSTRUMenT
P AneL
4 * if equipped
* if equipped
Preproduction model shown.
1090211_13_MKZ_QRG_LE_081412.indd 4-58/14/12 1:49 PM

SYnC® WiTH MYLinCoLn ToUCH™
SYNC is a hands-free, voice recognition system used for
entertainment, information and communication. SYNC…Say the word.
Use the four-corner, four-color touch screen to explore and
interact with your vehicle. The touch screen works the same way as
traditional controls, knobs and buttons do. Simply press the various
corners on your touch screen to personalize the many features and
settings of your vehicle all in one place. The system provides easy
interaction with your cellular phone, multimedia entertainment,
climate controls and navigation system.
A REVOLUTIONARY WAY TO CONNECT WITH YOUR CAR.
GENERAL TIPS
• Press the home icon at any time to return to your
home screen.
• For additional support, refer to your Owner’s Manual,
visit the website or call the toll-free number. See the
inside front cover of this guide for details.
Before You Get Started
• if you have the navigation SD card, make sure that it
is inserted into the media port or your navigation will
not work.
• The touch screen is sensitive, so make sure you press
the desired icon accurately and firmly.
CREATE YOUR OWNER ACCOUNT
• SYnC uses a wireless connection called bluetooth® to
communicate with your phone. Turn bluetooth mode on
in your phone’s menu options. This lets your phone find
SYnC. For more details on setting up your phone with
SYnC, visit SyncMyRide.com (U.S.) or SyncMyRide.ca
(Canada), or your phone manufacturer’s website.
• Set up your owner account at SyncMyRide.com (U.S.)
or SyncMyRide.ca (Canada). Register by following the
on-screen instructions. After registering, you can see
what complimentary services you are eligible for.
Why you need a SYNC
Owner Account
A SYnC owner account is required for
Vehicle Health Report activation and the
ability to view your reports online. You’ll
also be able to take advantage of all of
SYnC’s Services and personalization
features, such as saving your Favorites
and Points of interest (Poi). You’ll
receive the latest software updates
that add new places, directions and
information, and if you have questions,
you’ll get free customer support. Visit
the website or call the toll-free number
for more information. See the inside
front cover of this guide for details.
PAIRING YOUR PHONE WITH SYNC
in order to use many of the features of
SYnC, you must first pair and connect
your phone with SYnC. To pair your
phone for the first time: 1.
Make sure that your vehicle is in (P)
park and both your ignition and radio
are turned on.
2. Touch Add Phone in the upper left
corner of the touch screen.
3. Make sure that b luetooth is set to
on and your mobile phone is in the
proper mode.
4. When prompted on your phone’s
display, enter the six-digit Pin provided
by SYnC in the radio display.
5. The display will indicate when the
pairing is successful.
Note: The system may prompt you to:
• Set your phone as the primary/
favorite (the primary phone will
receive messages and voice mails).
• Download your phone book (this
is required to use the full set of
voice commands).
• Turn on 911 Assist®.
TIPS
• Make sure you accept SYnC’s
request to access your phone.
• To pair subsequent phones, please
refer to Pairing Subsequent Phones
in the SYNC chapter of your
Owner’s Manual.
PHONE
Voice-control your phone for hands-
free calling with your phone securely
put away. With SYnC, you won’t even
need to know the phone number. Just
say the name of the person you want
from your contacts.
Your phone connects you with many
other features and SYnC Services:
• Connect to SYnC Services for traffic,
directions, business searches and
information favorites.
• Connect to operator Assist to help
locate a listing or destination.
• Call for a Vehicle Health Report.
• Automatically connects with a
911 operator in the event of an
accident (the feature must be
turned on prior to an incident).
• Transfer calls seamlessly from
SYnC to phone as you get in or
out of your vehicle.




7
6
1090211_13_MKZ_QRG_LE_081412.indd 6-78/14/12 1:49 PM

SYnC® WiTH MYLinCoLn ToUCH™
USING MY PHONE WITH SYNC
Note: You must download your phone
book to make phone calls with voice
commands by name. Contacts listed in
all caps will require you to spell them
(i.e. JAKe will be J-A-K-e).
Making a phone call: Use SYnC to
make a phone call to anyone in your
phone book by pressing the voice
button
and when prompted, say any
of the following voice commands:




Note: You can also make phone
calls by pressing the voice button
. When prompted, give the voice
command, “Dial,” then verbally say
the phone number.
Answering incoming calls: Whenever you
have an incoming call, you will be able to
see the name and number of the person
calling in your display. Press the phone
button to answer an incoming call. You
can hang up at any time by pressing the
phone button
. Ending the call: Press and hold the
phone button.
Do not disturb mode:
This feature blocks
incoming calls and text messages and
saves them for later. You still have access
to outgoing calls when this feature is
active. Say the voice command “Do not
disturb on” to enable and “Do not disturb
off” to disable.
NAVIGATION*
Get started with your navigation system
by pressing the upper-right, green
corner. The available, voice-activated
navigation system includes:
• SiriusXM Traffic™
• SiriusXM Travel Link™
• Global positioning system
(GPS) technology
• 3-D mapping
• Turn-by-turn navigation
SET A DESTINATION
Set a destination through your touch
screen by using a street address, a
intersection, a point of interest (Poi)
or a place on the map. The easiest
way, however, is by voice. 1.
Push the voice button
. When
prompted say “Destination
street address”.
2. The system will ask you to say the full
address and will display an example
on-screen.
3. You can then speak the address
naturally, such as: “one two three
Main Street, Anytown.”
You can also use the touch screen to
enter a destination and narrow your
choices by city or street as you type.
You can choose from up to three
different types of routes:

• Fastest: Uses the fastest moving
roads possible.

• Shortest: Uses the shortest distance
possible.
• e co (e coRoute): Uses the most
fuel-efficient route.
Call at work
Call on mobile or cell
Call at home
TIPS • Save your favorite locations by
touching “Save to Favorites”.
• Change your map views from
Direction Headed, north Up or 3D.
CLIMATE
SYnC with MyLincoln Touch controls the
temperature, airflow direction, fan speed,
and activates other climate features
like heated front seats for you and your
passenger. To use voice commands to
operate climate, say a voice command
like “Climate temperature 72 degrees”
and MyLincoln Touch will make that
adjustment.
SET YOUR MYTEMP • Touch the lower-right, blue Climate
corner on the touch screen.
• Set your exact, desired temperature
using the + or - to adjust the setting.
• Press and hold the MyTemp button
until the background color goes solid.


ENTERTAINMENT
no matter how you store your music,
SYnC makes it yours to enjoy when you’re
behind the wheel. Just press the lower-
left, red corner of the touch screen. From
here, you can easily go between AM/FM,
Sirius, and other media sources.
SET YOUR RADIO PRESETS • Touch the entertainment corner on
the touch screen.
• Touch FM. • Touch Direct Tune. • enter the desired station and
touch enter.
• Touch Presets and then touch and
hold one of the memory preset
buttons to save it. You will hear a brief
mute and the sound will return when
the station is saved.
BRING IN Y
OUR OWN MUSICGain access to any audio source by voice
and even control how each operates, like
changing radio stations, CD tracks or
music on one of the following devices:
• CD • USb • bluetooth® Streaming • SD Card • A/V in For additional support, refer to your
Owner’s Manual, visit the website or call
the toll-free number. See the inside front
cover of this guide for details.
USING SYNC TO ACCESS

DIGITAL MEDIA
SYnC has a media hub with multiple inputs
allowing you to access personal media
from your digital devices. Plug in your USb
media devices such as phones and MP3
players and use SYnC to play all of your
favorite music.
Note: SYnC indexes all of your music.
The more music that is stored on your
device, the longer it takes SYnC to index.
Using voice commands to play music:
1. Plug your media player into your USb port.
2. Press the voice button
. When
prompted say “USB”, then follow-up by
saying one of the voice commands:
3. You will hear the command repeated back
to you and the selected item will play.
Play all
Play nex t song
Play song
Play album
* if equipped
9
8
1090211_13_MKZ_QRG_LE_081412.indd 8-98/14/12 1:49 PM

HEATED/COOLED*
FRONT SEATS
Press the heated seat symbol within

the climate control screen to cycle
through the various heat settings and
off. Warmer settings are indicated by
more indicator lights.
Press the cooled seat symbol
to cycle
through the various cooling settings and
off. Cooler settings are indicated by more
indicator lights.
MEMORY FUNCTION
The memory function allows a one-
touch recall of the driver seat, power
tilt/telescoping steering controls* and
power mirrors. Use the memory controls
located on the driver’s door to program
and then recall memory positions. To
program position 1, press and hold the
1 button until you hear a chime. Use this
same procedure to set positions 2 and
3 using the respective buttons. You can
now use these controls to recall the set
memory positions.
HEATED REAR SEATS*
Press the heated seat symbol on
the rear of the center console to cycle
through the various heat settings and
off. Warmer settings are indicated by
more indicator lights.
RETRACTABLE P ANORAMIC ROOF*
Located on the overhead console, your controls have a one-touch open and close
feature. To open the roof, press the button. it opens fully and will adjust its
opening automatically at certain speeds to help reduce wind noise. To manually
override this feature, press any button. it will reset after each ignition cycle. To close,
press the
button.
CoMF oRT
*if equipped.
*if equipped; preproduction model shown.
HEATED STEERING WHEEL *
To access, press the Climate corner on the
touch screen. Touch the heated steering
wheel icon
to warm the steering wheel.
TILTING HEAD
RESTRAINTS*
Your vehicle’s front head restraints
can be adjusted. Pivot the head
restraint forward by gently pulling
the top of the head restraint. once it
is in the forward-most position, tilting
it forward once more will release it to
its upright position.
Note: Do not attempt to force the
headrest backward after it has been
tilted. instead, continue tilting it forward
until the headrest releases to the
upright position.
13
12
1090211_13_MKZ_QRG_LE_081412.indd 12-138/14/12 1:50 PM