fuel pressure MAZDA 232 1990 Suplement User Guide

F2 OUTUNE
OUTLINE OF CONSTRUCTION
The fuel and emission control system of the new 323 4WD model is basically the same as that of the new
323 2WD modet; however, a turbocharger and knock control system are added to the BP TURBO model
and the fuel tank is designed
with separate right and left sections due to the installation of the propeller shaft
for the 4-wheel-drive system. A transfer pump is also equipped to pump the fuel from the left
to the right
(fuel pump side) section of the fuel tank.
The major points of difference between the 2WD model and 4WD model are as shown below.
93GOF2-705
Difference
Component 2WD 4WD
BP SUHC BP OOHC BP SOHC BP TURBU Remark
INTAKE AG! 1 Resonance duct 0 0 0 - -
SYSTEM
Resonance chamber 0
0 G -
VICS .-
ui- - -
Turbocharger - - -
0 Refer to page
FZ-12
I ntercooler - - -
0 Refer to page FZ-14
Air bypass valve - - -
0 Refer to page F2-14
FUEL SYSTEM Fuel pump control - - -
0 Refer to page F2-16
Transfer pump - -
0 0 Refer to page F2-18
Operating time for BP
Pressure regulator control 0 0 0 0
TURBO is different
(Refer to page F2-23)
Fuel pump reststorlrelay - - -
0 Refer to page F2-18
EVAPORATIVE
EMISSION
Fuel vapor vatve - -
CONTROL 0 0 Refer to page F2-16
SYSTEM
CONTROL
SYSTEM Point type
0 0
Throttle sensor 0 (MTX) -
-
Variable type - -
0 W-x) 0
Without heater
0 0 0 -
Oxygen sensor F
With heater - -
- 0 Refer to page F2-23
Water thermoswitch (on radiator)
-
Knock control system -
Overboost wami ng buzzer -
Turbocharge Indicator - -
C @TX) - NC cut-off system
- - 0
Refer to page F2-22
- -
0 Refer to page F2-21
- - 0 Refer to page F2-21
93GOF2-706

OUTLINE F2
SPECIFICATIONS
Low-pressure stde
1 High-pressure side
Nylon element (rn fuel pump)
Paper element
-
Pressure regulator
Regutating pressure .
t kPa (kg/cm2, psi) 1 265-3-l 4 (2.7-3.2, 38-46)
-t
Injector
me
Type oi drive
Resrstance
Idle speed cantrol (EC) valve
Type
Resistance
Purge control solenoid valve
Resistance Q
D
s2 [ High-ohmic
Electromechanical
12-76
Rotary
II-13
23-27
Water thermosensor
Resistance
Airflow meter
1 -20% ( -4V) 14.6-I 7.8
kf2
2o”c ( 68OF) 2.21-2.69
4OOC (104OF) 1.0-I .3
8O*C
(176OF) 0.29-0.35
E2++Vs Fully closed 200-600
Fully open 20--l ,200
Resistance Ez-Vc
E?+THAA
(1 ntake air
thermosensor)
200-400
-2o*c ( -4*F) 13,600-I 8,400
20°C ( 68*F) 2,2f O-2,690
60°C (14cPf) 493-667
I
Air cleaner
Element type
Fuel
Specification
* TEN terminal of diagnosis connector grounded.
The t mark indicates newly equipped parts.
Oi! permeated
Europe.....Unhzaded premium
Unleaded reguiar (RON 95 or higher)
(RON 91 or higher) Australia...Unleaded regular
(RON 91 or higher)
93GOF2-7 i 3

FUEL SYSTEM F2
FUEL SYSTEM
Due to the installation of the propeller shaft fur the 4WD, the fuel tank is designed with left and right section.
Therefore, a transfer pump is used to pump the fuet from the left to the right (fuel pump) side. The transfer
pump is mounted in the fuel tank, and is controlled by the transfer pump switch and the fuel pump control unit.
The fuel pump control system is adopted for BP turbo model.
CONSTRUCTION
PRESSURE REGULATOR
FUEL PUMP
FUEL PUMP
RESISTOR/REU\Y
TRANSFER PUMP
/
FUELPUM IP SWI’
TCH
FUEL VAPOR
FUEL TANK
i
4x4 CONTROL UNIT [BP SOHC]
FUEL PUMP CONTROL UNlT [BP TURBO]

F2 CONTROL SYSTEM
CONTROL
SYSTEM
STRUCTURAL VIEW
OXL STOPLIGHT SWITCH CLUTCH SWITCH
INJECTOR
P/S PRESSURE
SWITCH
‘GEN SE877
DtSTRIBUTOR
/ PUMP
CONTROL UNll
CONTROL UNIT
CONNECTOR
P REStSTORlRELAY
FUEL tNJ RELAY (MAIN RELAY)
AIRFLOW METER
SOLENOID VALVE
I NEUTRAL SWITCH
(PRESSURE REGULATOR)
WATER THERMOSENSOR
93GOf2.729

CONTROL SYSTEM F2
t OXYGEN SENSOR [BP TURBO]
I
CERAMlC HEATER
93GOF2-733
Because the temperature of the exhaust gas is inherently low in turbocharged engines, the BP Turbo model
uses a rapid heating ceramic heater to detect the air/fuel ratio,
PRESSURE REGULATOR CONTROL SYSTEM [BP TURBO]
PRESSURE
REGULATOR
I SOLENOID VALVE
(PRESSURE REGULATOR CONTROL)
FUEL
+ (FROM
DELIVERY PIPE1
II
FUEL INJ I
RELAY
(MAIN REU\Y)
I
II Ir
-__. _ - -’ VACUUM
CT0 DYNAMIC
Ill
CHAMBER)
BATTERY -
c
FUEL
(TO FUEL TANK)
nme*rn -.-a
To prevent percolation of the fuel during hot restart idle, vacuum to the pressure regulator k cut for 180
sec., and the fuel injection pressure is increased to slightly more than 284 kPa (2.90 kg/cm’, 41.2 psi).
Operating condition
l Coolant temperature: Above 90°C (194OF)
l Intake air temperature: Above 58OC (136OF)
g No-load condition
FZ-23

F2 TROUBLESt=iUUTlNG GUIDE
SYMPTOM TROUBLESHOOTING
Regarding symptom troubleshooting except LACK OF POWER, POOR XCELERATION, KNOCKING, and
HIGH UIL CONSUMPTION, refer to Workshop Manual [I 203-l O-89F (Europe) or 1204-l O-89F (Australia)].
19 LACK OF POWER [BP TIJR801
DESCRIP- *Performance poor under load when throttle valve wide open
TION *Reduced maximum speed
l Idle condition normal
[TROUBLESHOOTING HINTS1
3 Wastegate always open or opens early
3 Turbocharger damage
@ Factors other than engine malfunction
*Clutch sllpping
l Brake dragging
*Low tire pressure
l Incorrect tire size l Overloaded vehicle
@ Low intake air amount
*Throttle valve not open fully
*Clogged intake air system
TEP INSPECTlON
1
Install pressure gauge in intake air pipe and
check boost pressure at engine speed of
4,000
wm
CT page F2-45
Boost pressure:
More than 2.0 kPa (0.02 kglcm2, 0.3
psi)
@ Air/Fuel mixture lean
l Fuel iine pressure decreases l Fuel injection malfunction
@ Poor ignrtjon
@ Low engine compression
@ Alcohol blended fuel used
@ Knock control system malfunction
ACTION
Yes Go to Step 3
NO Check for air leakage and exhaust gas
leakage
4 If OK, go to next step
4 In not OK, repair
2 Check wastegate
Yes Remove intake air pipe from turbo-
f7 page F2-45 charger and check if compressor wheel
rotates smoothly t7 page F2-46
4 If OK, check air cleaner element
and throttle valve
+ If not OK, replace turbocharger
3 Check factors other than engrne Yes
l Clutch slipping Go to next step
1 8rake dragging
’
l Low tire pressure NO Repair or adjust
l Incorrect tire srze
FZ-32

TROUBLESHOOTING GUIDE F2
]sTFP 1 INSPECTION ACTION
I
Aerator depressed ful ty
rminal 1F voltage
: SELF TEST
ignition timing: BTDC 10 = I*
8 Check for correct fuel line pressure at idle’ Yes Check if fuel line pressure decreases
when accelerating quickly
Fuel line
pressure: 265-314 kPa (2.7-3.2 kg/cm’, 38-46 psi)
(vacuum hose to pressure regulator dis-
connected) 4 If decreases check fuel pump
maximum pressure*
If OK, check fuel line and filter for
clogging
4 If no decrease, go to next step
NO Low pressure
Check fuel irne pressure while pinching
fuel return hose
4 If fuel line pressure quickly in-
creases, check pressure
regulator' e If fuel lrne pressure gradually in-
creases, check for cloggrng be-
tween fuel pump and pressure
regulator
If not clogged, check fuel pump
maximum pressure* High pressure
Check of fuel return line is ctogged
4 If OK, replace pressure regulator
e If not OK. replace
- _
* Refer to 323 Workshop Manual
[I 203-1 O-89F (Europe), or 1204-lU-89F (Australra)].
FZ-33

F2 TROUBLESHOOTING GUIDE
20 POOR ACCELERATION [BP TURBO]
IESCRIP- . Performance poor while accelerating
rm
l Idle condition normal
[TROUBLESHOOTING HINTS]
3 Wastegate always open or opens early @ Low intake air amount
3 Turbocharger damage
l Throttle valve not open fully
3 Factors other than engine malfunction *Clogged intake air system l
Ciutch slIpping @ Air/Fuel mixture Iean l Brake draggrng l fuel line pressure decreases
l low tire pressure l Fuel Injection malfunction
l Incorrect tire size @ Poor Ignition
. Overloaded vehicle @ Low engine compression
@ Atcohol blended fuel used
TEP INSPECTION ACTION
-l Install pressure gauge
in intake air pipe and I Yes
1 Go to Step 3
check boost pressure at engine speed of 4,000
rpm
w page F2-45
Boost pressure:
More than 2.0 kPa (0.02 kglcm2, 0.3 psi)
No Check for air leakage and exhaust gas
leakage
4 If OK, go to next step
4 If not OK, repair
2 Check wastegate w page F2-45
Yes Remove Intake air pipe from turbo-
charger and check if compressor wheel
rotates smoothly w page F2-46
c3 If OK, check air cleaner element
and throttle valve
4 If not ok, replace turbocharger
3 Check factors
other than engine
Yes Go to next step l Clutch stipprng l 5rake dragging l Low tire pressure
No l Incorrect ttre size Repair or adjust
FZ-36

F2 TROUBLESHUOTtNG GUIDE
check fuel pump maxi-
fuel line and filter for
pump and pressure
High pressure
Check if fuel line is clogged
II. Measure resistance
r--- ---_--es-,
DAMAGE AND
DETERIORATION
* Refer to 323 Workshop Manual f1203-1 O-89F (Europe) 12041U-89F (Australia)].
F2-38

F2 TROUBLESHOUTING GUIDE
I 22 KNOCKtNG [8P TURBO] I
IESCW-
l Abnormal combustron accompanied by audible “pinging” noise rim
TROUBLESHOOTING HtNTS]
3 incorrect ignition timing (Too advanced) @ Low octan fuel used
2
Knock control system malfunction @ Air/Fuel mixture lean
3 Carbon deposits in cylinder l Fuel injection amount not correct
3 Overheating l Fuel line pressure decreases while accelerating
TEP INSPECTION ACTlON
1
Connect System Selector to diagnosis connector Yes Go to next step
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up’
ignition timing: BTDC 10 f lo
No Adjust
2 Check if “00” is displayed on Self-Diagnosis Yes Go to next step
Checker with igmtlon switch UN*
No Matf unction Code No. displayed
Check for cause (Refer to specified
check sequence) *
“88” flashes
Check ECU terminal 1 F voltage
Vottage: Approx. 12V
(Ignition switch ON) 0 page FZ-60
4 If OK, replace ECU
W: SELF TEST
4 If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check for correct fuel line pressure at idle* Yes Check if fuel Iine pressure decreases
when accelerating quickly
Fuel line pressure:
265-314 kPa (2.7-3.2 kg/cm2, 38-46 psi)
(vacuum hose to pressure regulator dis-
connected) 4 If decreases, check for clogging
between fuel pump and pressure
regulator
e If no decrease, go to next step
No tow pressure Check
fuel line pressure while pinching
fuel return hose
3 If fuel line pressure quickly in-
creases, check pressure
regulator*
4 If fuel line pressure gradually in-
creases, check for clogging be-
tween fuel pump and
pressure
regutator
If not clogged, check fuel pump
maximum pressure*
- -
.-
Refer to 323 Workshop Manual [1203-IO-89f (Europe} or t204-IO-89f (Australia)]. F2-40