check engine MAZDA 232 1990 Suplement Owner's Manual

F2 CONTROL SYSTEM
Terminal voltage [BP TURBO]
eminal input Output , 1 Connected to Test condition Correct voltage Remark
IA - - Battery Constant Approx. 12V for backup
15 0 Main relay OFF Approx. OV
(FUEL INJ relay) tgnltlon switch
-
ON Approx. 12V
1c 0 1 Ignition switch Wniie cranking Approx. 1 OV
-
(START)
lgnrtron switch ON Approx. OV
ID 0 Self -Diagnosis Test switch at “SELF-TEST” With Self-
Checker Lamp illuminated ior 3 sec. after ignition Approx. 5V Diagnosis Check-
(Monitor lamp) switch OFF* ON er and System
Lamp not illuminated after 3 sec. Approx. 12V Se’ector
Test switch at
“02 MONITOR” at idle
Monitor lamp illuminated Approx. 5V
Test switch at
“02 MONITOR” at idle
Monitor lamp not illumrnated Approx. 12’4
-lE - - - -
- -
1F 0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2.5V l With Self-
Checker switch OFF -+ ON Diagnosis
(Code Number)
Buzzer not sounded after 3 sec. Approx. 12V Checker and
Buzzer sounded Below 2.9 System Selector
l With System
Buzzer not sounded Approx. 12V Selector test
switch at
“SELF-TEST’ ’
I I 1G
0 Igniter
7H
0 Solenoid vahe
(Wastegate)
l!
0 Fuel pump
resistor/relay
I
lJ I r-Tcreiay Ignition switch ON
ld!e
Engine speed below 5,300 rpm
Engine speed above 5,300 rpm
While cranking
Idle
Ignition switch ON
AK switch ON at idle 1 Approx. OV
-
Approx. 0.2V
Approx. 12V
-
Below 1.5V
Approx. 1 OV
-
I3elow 15V
Approx. 12V
Below 2.5V
AIC switch OFF at idle Approx. 12V
-
IK 0 Diagnosis System Selector test switch at
connector
(TEN terminal)
1L - - -
- -
-
IM
t 0
1 Ground (Australia) Constant Below 1 .OV Not used
(Except Australia)
F2-60

F2 CONTROL SYSTEM
93GOF2-79; 2
93GOF2-793
93GOFZ794
1
OXYGEN SENSOR [BP TURBO]
Inspection
Sensor
1. Warm up the engine to normal operating temperature.
2. Disconnect the oxygen sensor connector.
3. Connect a voltmeter to the oxygen sensor terminal @.
4. Run the engine at 4,500 rpm untiI the voltmeter indicates
approx. 0.7V.
5. Increase and decrease the engine speed suddenly and
measure the vottage.
Voltage
Engme speed Voltage (v-)
Decelerating o-0.4
Accelerating 0.5-l .o 6. Connect the
SSTs to the diagnosis connector.
7. Set the system selector select switch to 1 and the test switch
to 02 MONITOR.
8. Increase the engine speed to
between 2,000 and 3,000
rpm, and verify that the monitor lamp flashes for 10 seconds.
Specification:
Monitor lamp flashes more than 8 times/IO sec.
Heater 1. Disconnect the oxygen sensor connector.
2. Check resistance between oxygen sensor connector ter-
minals @ and 0.
Resistance: Approx.-6& [at 20°C (68OF)]
Replacement 1. Disconnect the oxygen connector. ’
2. Remove the oxygen sensor.
3. Install the new oxygen sensor and new washer.
4. Tighten the oxygen sensor to specified torque.
Tightening torque:
29-49 N-m (3-5 m-kg, 22-36 ft-tb)

H OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
A hydraulic clutch control mechanism is used.
The basic construction is the same as that of 323 2WD model, but there is no interchangeability of parts
except for the release cylinder.
1. An assist/return spring is used on the BP DOHC Turbo model to reduce the required clutch pedal effort..
2. The hydraulic clutch master cylinder for the 8P DOl-lC Turbo model has a built-in check valve.
3. To improve clutch operation feeling and increased parts life, a friction plate and needle roller bearings
are used between the release fork and the release bearing.
93GOHX-704
SPECIFICATIONS
Hem
Clutch control Engine/Transaxle
BP SUHC BP DOHC Turbo
GSMX-R
Hydrautic
Clutch cover
Type
Set load
N (kg, lb) Diaphragm spring
3,846 (392, 862) 5,494 (560, I ,232)
Outer diameter 1
mm (in) 225 (8.858) 230 (9.055)
I 1 nner diameter mm (in)
I 150 (5.906)
I 155 (6.102) I
CI utch disc
Pressure plate side
mm {in) 4.1 (0.161) 3.2 (0.126)
Thickness f
Flywheel side
mm (in) 3.5 (0.138) 3.2 (0. f 26)
I Type I Suspended
I
Clutch pedal LHD 6.55 Pedal
ratio
RHD 6.7
Full stroke mm (in)
I 135 (5.32)
I
Height (With carpet) mm [in)
I I 96-204 (7.72-8.03)
I
Master cylinder Inner diameter
mm {in)
I 15.87 (0.625)
Release cylinder inner diameter
mm (in)
I - 19.05 (0.750)
I
Clutch fluid SAE J1703 or FMVSSI 16 DOT-3
93GOHX-705
H-4