battery MAZDA 232 1990 Workshop Manual Suplement

CAUTION GI
i I 9MUGIX-022

9MUGIX-02:
9MUGIX-02
CAUTlON WITH ELECTRICAL PARTS
Battery Cable
Before disconnecting connectors or replacing electrical parts,
disconne@ the negative battery cable.
Connectors
Removal of connector
Never pull on the wiring harness when disconnecting con-
nectars.
Connectors can be removed by pressing or pulling the lock
lever as shown.
Locking of connector
When locking connectors, make sure to listen for a click that
will indicate they are securely locked.
Inspection
1. When a tester is used to check for continuity or to measure
voltage, insert the tester probe from the wire harness side.
Gl-13

CAUTION GI
I 9MUGIX-031
PULLER
t Fuse
Replacement
1. When replacing a fuse, be sure to replace it with one of
specified capacity.
If a fuse again fails after it has been reptaced, the circuit
probably has a short circuit and the wiring should be
checked.
2. Be sure the negative battery terminal i
fore replacing a main fuse @A).
3. When replacing a pullout fuse, use the
in the fuse box cover. ; disconnected be-
use puller supplied
Wiring Harness
Wiring color codes
Two-color wires are indicated by a two-color code symbol.
The first letter indicates the
base color of the wire and the sec-
ond the color of the stripe.
1 9MUGIX-029
LG Light Green - - CODE
B COLOR
Black CODE )
0 COLOR
Orange
BR Brown P Pink
1
G
GY
t
LB Green
Gray
Blue
Light Blue R
! Red
V Violet
W White
Y Yellow
Gl-15

A PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
pieziG-
INSPECT and ADJUST, if necessary, the following Items to
specification:
D Glass, exterior bright metal and paint for damage
Cl Wheel tug nuts
9 Trre pressures
LII All weatherstrips for damage or detachment
Z Operation of bonnet release and lock
D Operation of trunk lid, hatch and fuel lid opener
(it equipped)
3 Door operation and alignment
5 Headlight aiming
INSTALL the following parts:
D Wheel caps or rings (if equipped)
D Outside mirror(s)
[ UNDER BONNET-ENGINE OFF )
INSPECT and ADJUST, if necessary, the foIlowIng items to
specification:
Cl Fuel, coolant and hydraulrc lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level (if equipped)
D Brake master cylinder fluid levels
0 Clutch master cylinder fluid levels (if equipped) q
Windshield washer reservoir fluid level
D Radiator coolant level and specific gravity
Ll Tightness of water hose clamps
I3 Tightness of battery terminals, electrolyte level and specific
gravity
c) Manual transaxle oit level
D Drive belt(s) tension
C; Carburetor linkage (choke control, wide open throttle posi-
tion, etc.) (carburetor model only)
D Accelerator cable and linkage for free movement
D Headlight cleaner and fluid level (if equipped)
BLEED air from fuel line (diesel engine only)
CLEAN the spark plugs (except for diesef engine)
piicis-1
INSTALL the foflowing parts:
C Rubber stopper for inside rear view mirror (if equipped)
c! Fuse for accessories
CHECK the operation of the following items:
Cl Seat controls (sliding and redining) and head rest
ci Seat belts and warnrng system
Z! Ignition swrtch and steering lock
III Power window {if equipped)
0 Door locks including child proof door locks
0 Inhibitor switch
(ATX only)
Z All lights including warning and indicator lights
0 Ignrtron key reminder buyer (if equipped) Cl Horn, wipers and washers (front and rear, if equipped)
D Antenna (if equipped} q
Cigarette lighter and clock (if equipped)
I2 Remote controt outside mirror
(if equipped) q
Heater, defogger and air conditioner at various mode selec-
tions (if equipped)
c3 Sunroof (if equipped)
CHECK
the fotiowing items: q
Presence of spare fuse
c3 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
Cl Operation and fit of windows
D Pedal height and free ptay of brake and clutch pedal
Cl Parking brake
i UNDER BONNET-ENGtNE RUNNING AT ]
1 OPERATtNG TEMPERATURE
CHECK the following items:
Cl Operation of idle-up system for air conditioner or power steer-
ing (if equipped)
13 Automatic transaxle fluid level
D Initial ignition timing
(except disel engine) q
Idle speed
El Operation of throttle position sensor (EGI engine)
13 Operation of cold start device and glow plug warning light
(diesel engine only)
D Operation of dash pot [EGI engine)
t
ON HOtST 1
CHECK the following items:
U Underside fuel, coolant and hydraulic lines, fittings, connec-
tions and components for leaks q
Tires for cuts or bruises
Cl Steering linkage, suspension, exhaust system and all under-
side hardware for
looseness or damage
1 ROAD TEST 1
CHECK the foliowing items:
II Brake operation
D Clutch operation
0 Steering control
c3 Operation of meters and gauges
0 Squeaks, rattles or unusual noises q
Engine general performance
c3 Emergency Iocking retractors
rAFTER ROAD TEST 1
REMOVE the seat and floor mat protective covers
CHECK for the necessary
owner information materials, tools
and spare tire in vehicle
93EOAX-002
A-2

A SCHEDULED MAINTENANCE SERVICES (Australia)
lumber of months or km, whichever cumes first
P
_ 48 54 60 1 66 72
5
60 67.5 75 90 .--- .-- -
.-m-w --v-w _ _ -_-- - - _ _ - -
_ -- - - --- __-
_-
-- -- (82.5
Exhaust manifold bolts and nuts (except turbo) T 1
I i T 1
1 T
Engine timlrtg belt”’ Replace every 105,000 km
Drwe belts * a
A I 1 I 1 1 I 1
! ’ I I 1 1
Engine oil * ’ Except turbo models 1 RIR\R/RIRIRIR R R,R R R/R
For turbo models R
Replace every 5,000 km or 6 months
r-k:1 c:t+*-* 1 Except turbo models
R 1 R 1 1 R ( ) R ( 1 R ( 1
R 1 f R
-
1 VII IIIIc;I 1 For turbo models I R 1 ReDlace everv IO.000 km or E
Engine coolant (Wrth Reservoir)
Fuel
system
Replace e&y 24 months
For F-i. system
Idle speed (if equipped Idle 1 1 1 I
I speed controf)
Air cleaner element 1
R , I R I R
Fuet filter
I I? R R
~ Fuel lines and hoses
1 I 1 I I 1 I I 1 1
Ignition system
t Initial ignition timing
Spark plugs i I I I -1 I I
I I I I I
f
Evaporative emission control system
Evaporative system
Throttle sensor
Exhaust emission contra! system
[ Dashpot
(Except for ATX) I 1 I
1 1 I 1 1 t 1 1 1 1 1 ! 1 1 I 1
Electrical system
Battery electrolyte level and specific gravity ]
I 1 1 I 1 t I ’ 1 1 I 1 f I ( 1
I 1
Chassis and body
Brake lines, hoses and connections
Brake fluid * a
Parking brake
Disc brakes
1 Power steering fluid and line Ilf &uiDDedl
I 1 1 I I I
I 1 1 III II
I ’
I I
Steering operations and gear housing
I
1 1 I --r--j- 1 I
I
Steerino linkanes. rack auide and tie rod pnds .-- --
----.“.a ..‘-~--, J- -.-- _.- .-- -..-- I I I t I 1 1 I I I I I I I 1
Manual transaxle oil I \\!‘I rl\jl I 1 I R III
1 Transfer Automatic carrier oil or 09 automatic transaxle fluid level
1 1 I 1 111 I 1 I l 1 I 1 I 1[11i t I 1 I 1 I I 1 I
R 1 Iii 1 I
1 Rear axle oil (Differential) 1 t I I I I I I I I
t ’ I r . ’ 1 . I I I I I R I 1
I
I I
i T
1 T T T 1 T [ T I 1 T
Front suspension ball joints
Bolts and nuts on chassis and body
I I I . I ! ,
I 1 I . I 1 ’ I I ’
Drive shaft dust boots
I
I 1 I 1
I 1 1 I
~~
- - ’ C1utcl-1 pedat
Clutch fluid
1
A-4

SCHEDULED MAtNTENANCE SERVICES (Europe) A
Maintenance Number of months or km (miles), whichever comes first
Months” - 6 1 12 18 ‘24 30136 42 48
Maintenance Kilometers 1,000 10,000 20,000 30,000 40,000 50,000 ( 60,000 70,000 80,000
(Miles) (600) (6,000) (12,OOO)~(l8,0~0) (24,000) (3O,UOO))(36,000) (42,000) j48,OOU)
Engine
!nrake and exhaust manifold nuts (80&j
Owe belts *’
Engrne timing belt l 3
Engine oil flurbo)‘4
Engine oil (Non-turbo)“4
Oil filter’4
Cooling system (I ncludrng
coolant level adjustment)
Engine coolant T 1 T T
A 1 1 A A 1 A A
Reptace every 100,000 km
{60,000 miles)
Replace every 5,000 km (3,000 miles) or 6 months
R R 1 R R R R ‘ R R R
R R R R R R R ’ R
I I I I
Replace every 2 years
Fuel system
Idle soeed
I A 1
Air cleaner elemenf*5 I f R E
R
Fuel fitter
R R
fuel 11~s and hoses 1
t 1 I I I I
Ignition system
lrritiai ignition timing
Spark plugs
Spark plugs (Only for Sweden) 1 I I I 1 I I 1 I I 1 I
A 1 A A 1 A
Adjust every 30,000 km {
18,000 mils)
Evaporative emission control system
Throttle sensor
Throttle sensor (Only for
Sweden)
Evaporative system Evaporatwe system Khlv
for Sweden) 1 1 Aj 1 A ( [ A ] 1 A
Adjust every 80,000 km (48,000 miles)
I 1 I [ I 1
I I [ 1 I
lnsoect everv 80.000 km (48.000 miles)
Electrical system
Battery electrolyte level and specific gravity
A 1 A A ’ 1 A ; A *
All Electrical system *’ I I 1 I I I I I I
Headlight alignment A A A I
c I A ,
Chassis and body
clutch Dedal
Clutch fluid
Brake lines, hoses and connectrons
Brake pedal
Brake fluid”’
Parking brake
Power brake unit and hoses
Disc brakes
Power steering fluid
Power steering system and hoses I
I I 1 1 1 I I
I I
I
I I I I 1 1 I
1
1 I I
I I I I t ! I I
I I I R I 1 I R
A A A A
I I I I
I 1 I 1
I 1 I I I I j I ,
I
I 1 I 1
I
93GOAX-708
A-9

Bl SUPPLEMENTAL SERVICE tNFORMAT1ON, REMOVAL
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison with Workshop Manual [Europe (I 203-I U-89F),
Australia (1204- 1 O-89!=)].
Engine
l Removal
l Installation 93GOF31-705
REMOVAL
Warning
w Release the fuel pressure.
PROCEDURE
1. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil.
3. Remove in the order shown in the figure, referring to Removal Note.
Step 1
t
I
*ATX ONLY 1
93GOBl-706
1. Undercovers
2. Side covers
3. Resonance chamber and air cleaner assembly
4. Battery bracket, cover and bafiery
5. Battery carrier and battery duct
6. Accelerator cable
7. Radiator hose
8. Coolant reservoir hose
9. Cooling fan connector
IO. Radiator switch connector (ATX)
1 f . A/C cut switch connector (ATX) 12. Oil cooler hoses (ATX)
13. Radiator bracket
14. Radiator and cooling fan assembly
15. P/S and/or A/C drive belt
16. P/S oil pump and bracket
Removal Note .._...._...__......... . . . . . . . page BY -7
17. A/C compressor
Removal Note.. . . . . . . . . . . . . . .._. . . . . . . . ._. page Es1 -7
i 8. Crossmem ber
19. A/C compressor bracket
20. Coolant reservoir
61-6

Bl INSTALLATION
93GOE 1-73;
03UOBX-84
. .
‘, .
L .G,
. . ‘?.
- -. _ .:
.L ‘.. :-.:
.-_: _. _, _-
.
-_
. :
Cl :- . .
: .._.
. . ._-
;: , ‘. ’
,.. .- -
. ‘L,
93GO3 l-73’
-DEFLECTiON CHfiCKIN:
g3GOBj-717
Bl-22
P/S oil pump and bracket
1. Install the P/S oil pump and bracket.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
Drive belt
I. fnstall the P/S and/or A/C drive belt.
2. Adjust the drive belt deflections. (Refer to page Bl-2.)
Radiator
and cooling fan assembly
f . Install the radiator and cooling fan assembly.
Tightening torque:
7.8-I 1 N-m (80-I 10 cm-kg, 69-95 in-lb)
2.. Connect the cooling fan connector.
3. Connect the radiator switch connector.
4. Connect the A/C cut switch connector.
5. Connect the oil cooler hose. (ATX)
6. Connect the coolant reservoir hose.
7. Connect the upper and lower radiator
@TX)
Pm
hoses.
Caution
l Position the hose clamp in the original location on
the hose, and squeeze it tightly with large pliers to
ensure a good fit.
Accelerator cable
I. Install the accelerator cable.
2. Adjust the cable deflection by turning nuts @
Deflection: I-3mm (0.04--0.12 in)
-
Battery duct, battery carrier, and battery
I_ install the battery duct.
2. Install the battery carrier.
Tightening torque:
7.8-I 1 N-m (80-110 cm-kg, 69-95 in-lb)
3. Install the battery, cover and the battery bracket.
Tightening torque:
2.9-5.9 N-m (30-60 cm-kg, 26-52 in-lb)
4. Connect the positive battery cable.

INSTALLATION Bl
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 Nm (I-9-2.6 m-kg, 14-19 Mb)
@: 7.8-11 Nm (80~-110 cm-kg, 69-95 in-lb)
2. Connect the airflow sensor connector.
Resonance chamber
1. lnstail the resonance chamber.
Tightening torque:
7.8-W Nm (SO-11 0 cm-kg, 69-95 in-lb)
Undercover and side cuver
1. install the undercovers and side covers.
Steps after installation
1. If the engine oil was drained, refill with the specified amount and type of engine oil.
2. Fill the radiator with the specified amount and type of engine coolant.
3. Fill the transaxle with the specified amount and type of transaxle oil. (Refer to pages J3-36, K3-134.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage
(2) Ignition timing and idle speed
(3) Operation of emission control system
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
93GOSi-719
al-23

D
D
SUPPLEMENTAL SERVICE iNFORMATION, COMPRESSION 82
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison with Workshop Manual [Europe (7 203~IO-899,
Australia (I 204-1 U-89F) 1.
Compression
l Inspection
Engine
l Removal
l Engine stand mounting
l Engine stand dismounting
l Ins:attaIion 93GQ32-77 I
COMPRESStON
If the engine exhibits low power, poor fuel economy, or poor idle, check the following:
1. Ignition system (Refer to Section G.)
2. Compression
3. Fuel system (Refer to Section F3.)
93G032-774 93GO32-712
1NSPECTION
1. Verify that the battery is fully charged. Recharge it if
necessary.
2. Warm up the engine to normal operating temperature.
3. Turn the engine OFF.
4. Remove all of the spark plugs.
5. Disconnect the ignition coil connector.
6. Connect a compression gauge to the No.7 spark plug hole.
7. Fully depress the accelerator pedal and crank the engine.
8. Record the maximum gauge reading.
9. Check each cylinder in the same manner.
Compression:
1,059 kPa (IO.8 kg/cm2, 154 psi)-300 rpm
Minimum:
785 kPa (8-O kg/cm2, 114 psi)-300 t-pm
Allowable difference between cylinders:
196 kPa (2.0 kglcm2, 28 psi) max.
IO. If the compression in one or more cylinders is low, pour a
small amount of engine oil into the cylinder and recheck
the compression.
(1) If the compression increases, the piston, piston rings,
or cylinder waII may be worn.
(2) If the compression stays tow, the valve may be stuck
or seating improperly.
(3) If the compression in adjacent cylinders stays low, the
cylinder head gasket may be defective or the cylinder
head distorted.
1 I. Connect the ignition coit connector.
12. Apply antiseize compound or molybdenum-based lubricant
to the spark plug threads.
73. Install the spark plugs.
Tightening torque:
15-23 N-m (1.5-2.3 m-kg, If-17 ft-Ib)
82-11

B2 REMOVAL
REMOVAL
Warning
l Release the fuel pressure. (Refer to Section FZ.)
PROCEDURE
i. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil.
3. Remove in the order shown in the figure, referring to Removaf Note
Step 1
1. Strut tower bar
2. Undercovers and side covers
3. Air cleaner assembly
4.
Battery bracket
5. Battery cover
6. Battery
7. Battery carrier
8. Accelerator cable
9. Radiator hoses
10. Coolant reservoir hose
f I. Cooling fan connector
12. Radiator switch connector
13. Radiator bracket
14. Radiator and coofing fan assembly
15. Battery duct
16. Air pipe and air bypass valve
17. Intercooler and air pipe
Removat Note . . . . . . . . . . . . .._.. m _._._..., page 82-U
18. Air pipe and gasket
19. P/S and/or AK drive bett
20. P/S oil pump and bracket
Removal Note . . . . .._.__.....~..~........ page BZ-13
21. A/C compressor
Removal Note . . . . . .._................... page 82-I 3
22. Crossmember
02-12