section b2 MAZDA 323 1992 Suplement User Guide

TURBOCHARGER CONTROL SYSTEM F3
INTERCOOLER
Removal / Installation
1 I Remove the front bumper. (Refer to Section S.)
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
7-i-11 N-h l80-110 kgfem, 69-95 In-lbf 1
1.
Air hose 2. Intercooler
wrn 1 kgf-m, ft-lbf I
13EOF3-34:

CONTROL SYSTEM F3
VS: Battery voltage
Incorrect voltage Possible cause
Ab&e OV
l Poor contact at ground terminal l Open circuit in wiring from ECU to ground
Always approx. OV or approx. 2V
l Refer to Code No. 02 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
Always approx. OV or approx. 1.5V
l Refer to Code No, 03 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV
Always OV
- -
l Refer to Code No. 05 Troubleshooting
(Refer to 323 4-Wheel drive Workshop Manual (1229-10-891))
l Short circuit in wiring from ECU terminal 2K to throttle sensor, or airflow
meter
l Poor connection at ECU connector l ECU matfunctlon
Below 4.5V or above 5.5V
-
l ECU matfunction
l Refer to section 1
Always OV
l Throttle sensor malfunction l Short circuit in wlnng from ECU termrnal 2M to throttle sensot l Poor connection at ECU connector
. ECU malfunction
Always approx. 5V . Throttle sensor misadjustment
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always constant
l Open circuit in wiring from ECU terminal 2M to throttle sensor
. Open circurt in wiring from ECU terminal 2K to throttle sensor
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always above 1V 1 . Throttle sensor mtsadjustment
Always OV (after warm-up)
Always approx. IV (after warm-up)
l Refer to Code No. 15 Troubleshooting
(Refer to 323 Workshop Manual (1203-I O-89F))
l Refer to Code No.17 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV or approx. 5V
l Refer to Code No. 08 Troubleshooting
(Refer to 323 Workshop Manual (t203-lo-89F))
Always OV or approx. 5V
Always OV or approx. 5V
l Refer to Code No. 10 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
l Refer to Code No. 09 Troubleshooting
(Refer to 323 Workshop Manual (1203-10.89F))
Always OV
I
l Indicator broken l Open or short circuit In wiring from ECU 2R to ignition switch
13EOF3-36;
F3

G OUTLINE, SUPPLEMENTAL SERVICE INFORMATION
SPECIFfCATfUNS
Item
8attery
Dark current Voltage
Type and capacity Engine
v
(20-hour rate)
mA BP DOHC
12
55D23L (60Ah)
Max. 20
Type Output V-A f “‘i j.,: i .:.. ‘:.. ,, j j.: i.‘: ;:;:i :j;&?.:. .: .:.
__ : . . s.i-....‘:‘:. _.. j ;.’
Regulator type Transistorized (built-in IC regulator)
Regulated voltage v
14.1-14.7
I
C?*..*rlrrrl
Brush length mm [rn] }e 21.5 (0.846)
8.0 10.315)
I Drive belt deflection I 5.5-7.0 { 0.22-0.27 )
mm (intB8N (lOkgf,22Ibf) usea 6.0-7.5 (0.24-0.29 1
Limit 8.0 (0.311
, Type Direct
Starter Output v*$# : : ;..;. ‘:‘.. ._ .; : :‘: 7.:
.. .::“:.:j 1 ,5
. . . . .j$$g;g$y .“. :yy
Brush length mm {in] - Standard 17 [0.67]
Minimum
11.5 IO.4531
Dlstnbutor soark advance Electronic soark advance (ESA)
@EN termind of diagnosis connector grounded) II) f lo
I 1 Prtmary coil
**4 nn*
Ignltbon co11 Reststance 3
(at 20°C [68*F])
in IO-16 kQ lgnrtlon timing BTDC f ar
wrndfnb
I
Secondary 1
coil WindIn.. v.0 I
--v.yy 1
Spark plug NGK
NIPPONDENSU
Firing oraer
*Standard pfug
SUPPLEMENTAL SERVICE INFORMATION
The following points shown in this section are changed in comparison with 323 Workshop Manual
(1203-l O-89F) and 323 Workshop Manual Supplement (I 275-l O-91 C).
l Alternator . Starter
Specifications Specifications
l Spark plug
Specifications
13EGGX-303
G-2

M SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE INFORMATION
The foIlowIng points in this section are changed in comparison with Mazda 323 Workshop Manuals
(1206-f O-89F) and (1229-l O-89L).
Front axle
l Removal I Inspection I Installation
l Disassembly I Inspection / Assembly
Rear axle
l Removal / Inspection I Installation l Disassembly / Inspection I Assembly
13EOMX-305
t
,
c
.
c!
M-4
.
r&
-s
FRC
PREF
SST
-m
49 0’
Pulle
--
49 Gl
Atkd
(Part
49 Gc
--
49 FC
I n.stail beam
--
49 F3
Attact
:Part
t 49 FO
--
49 Frl
4ttac P 58 8 : Part < $9 Fcl,
--
a9 G3
nstallt

M FRONT AXLE
WHEEL HUB, STEERING KNUCKLE
RemovaI / Inspection I Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. InstaH in the reverse order of removal, referring to Installation Note.
Caution
l Loosely tighten the shock absorber bolts. Lower the vehicle and tighten the bolts to the specified
torque with the vehicle unladen.
4. Adjust the front wheel alianment.
16-22 ]1.6-2.3, 12-161 I
19.0-l 2.0, 65-86.7 I
1. Wheel hub nut
2. Wheel and tire
3. Locknut
Removal Note . . . . . . .._.. . . . . . . . . . . . . . . . . . . . page M-7
installation Note .I.........,..,............ page M-7
4. Brake caliper assembly
Service . _. . . . . . . . . ,__. . . , , . ._. _. , , . . . , . ._ ._. . . . . . Section P
5. Disc plate
lnspectioti .~~*.......*~...,......,,,.....*~...~. Section P
6. ABS wheel speed sensor (if equipped)
7. Tie rod end
Removal Note . . . . . . .._.......... I . .._.....= page M-7
lnstallatiofi Note . . .._... _.__......,....... page M-7
M-6
8. Lower ball joint
9. Steering knuckle, wheel hub, and dust cover
Inspect-wheel hub for cracks and damage
Inspect knuckle spindle for cracks and
damage
Inspect dust cuver for damage and dis-
tortion
Disassembly I Inspection I
Assembly . ..C1..............~...,.....,.....
page M-8

REAR AXLE
WHEEL HUB, KNUCKLE
Removal I Inspection / installation
1. Remove in the order shown in the figure, referring to
Removal Note. 2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to Installation Note.
Caution
l Loosely tighten the shock absorber bolts. Lower the vehicle and tighten the bolts to the specified
torque with the vehicle unladen.
4. Adiust the rear wheel alianment.
16-22 1?.6-2.3, 12-16 I
7
IO.o-13.0,
66-66.7 1 1. Wheel and tire
2. Locknut
Removal Note..; . . . . . . . . , . . . . ,.......- -.. page M-f 3
Installation Note .._...,.,...._.__........ page M-13
I$ Brake caliper assembly
Service . . . . . . . . . . . ..e......._......... ,.,...,....
Section P
4. Disc plate
‘Service ..I....................__....... . . . . . . . . . Section P 5. Af3S wheel speed sensor (if equipped)
6. Wheel hub, knuckle
Disassembly I Inspect& /
Assem bty . . . . . . . ..I..........*..*.*...-... page M-14
Inspect wheel hub and knuckle for damage
or cracks
Inspect dust cover for damage or defor-
mation
M-12

P SUPPLEMENTAL SERVICE INFORMATION I
. .
SUPPLEMENTAL SERVICE
INFORMATION
The following points in this section are changed and added in comparison with Workshop Manuals
(1206-I 0-89F), (I 229-I 0-89L) and (12751 O-91 c).
Air bleeding (with ABS)
Power brake unit (SST newly established)
l Inspection (on-vehicte)
Proportioning valve (SST newly established)
l Inspection
Front brake
l Inspection (on-vehicle)
Removai I Inspection / Installation
Disc pad
l Replacement
Disc plate
l Inspection
Caliper
l Disassembly I Inspection I Assembly
Rear brake
l Inspection (on-vehicle)
l Removal i Inspection I Installation
Disc pad
l Replacement 4
Disc plate
l Inspection
Caliper
l Disassembly I Inspection I Assembly 13EOPX-305
4
P-4
CON
PREP,
SST
Pm
49
ue4
Gauge, pressL r
(Part d
49 um
Pa
49 uw
HOti (Part 0;
49 uu4;
49 1258
Duiler, LH

%
:
1 SUPPLEMENTAL SERVICE INFORMATION, WHEELS AND TIRES Q .
SUPPLEMENTAL SERVICE INFORMATKM
The following point in this section is changed in comparison with the Mazda 323 Workshop Manual Voi-
ume 2 (1206~IO-89F).
l Wheels and tires
I Wheel balance adjustment
13EOQX-30 13EOUX-305
j
WHEELS AND TIRES
I
WHEEL BALANCE ADJUSTMENT
If a wheel becomes unbalanced or if a tire is replaced or
repaired, the wheel must be rebalanced to within specifi-
cation.
Maximum unbalance (at rim edge): 9 g IO.32 oz j
Caution
l Do not use more than two balance weights on the
inner or outer side of the wheel,
l One batance weight; max. 60 g (2-f oz 1.
l if the total weight exceeds IOU g (3.5 or] on one
side, rebalance after moving the tire around on the
rim.
l Attach the balance weights tightly to the wheel.
. Select suitable balance weights for aluminum alloy
wheels.

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if

T ~WPe~MENTAL SERVICE INFORMATION, EXTERIOR LIGHTING SYSTEM
SUPPLEMENTAL SERVICE INFORMATION
The following points shown in this section are changed in comparison with 323 Workshop manual supple-
menP(1229-1 O-89t) and 323 Workshop manual supplement (1275-l O-91 C>.
Front fog light
l Removal I Installation
13EOTX-305
EXTERIOR LIGHTING SYSTEM
FRONT FOG LIGHT
Removat / tnstaitation
I. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
I. Radiator grille
2. Front combination light
3. Headlight 4. Front bumper
5. Front fog light
T-4