service MAZDA 323 1992 Suplement User Guide

SUPPLEMENTAL SERVICE HWURMATION B2
SUPPLEMENTAL SERVICE 1NFORMATION
The following points in this section are changed in comparison with 323 Workshop Manual [Europe, AUS- tfilia (I 229-I O-89L)j.
Engine
l Removal
. Installation
I
m I
l The intercooler installation position is changed because the intercooler is enlarged. With this change, the
engine can be removed and ‘installed without removing the intercooler. The engine removal I installation
procedure is the same as of the previous BP-DOHC Turbo engine.
13E082-313
82-9

F3
c
FUEL AND EMISSION
CONTROL
SYSTEMS
i
INDEX . . . . . . . . l ..,.... *..,. . . . . . . m...*.*...*..... F3- 2
UUTLtNE
...................................... F3- 4
OUTLINE OF CONSTRUCTION.. ....
F3- 4
SYSTEM DIAGRAM ...................... F3- 5
VACUUM HOSE ROUTING
DIAGRAM
................................. F3- 6
WIRING DIAGRAM.. .....................
F3- 7
ECU RELATIONSHIP DIAGRAM ...... F3- 8
SPECIFICATIONS.. ....................... F3- 9
TURBOCHARGER CONTROL .......... F3-IO
OUTLINE
.................................... F3-10
SYSTEM DIAGRAM ...................... F3-10
WASTEGATE CONTROL ............... F3-11
FUEL SYSTEM
.............................. F3-12
OUTLINE ....................................
F3-12
CONTROL SYSTEM .......................
F3-13
STRUCTURAL VIEW .....................
F3-13
PRESSURE REGULATOR
CONTROL SYSTEM ....................
F3-14 SUPPLEMENTAL SERVICE
tNFOF?MATtON
............................. F3-I 5
SELF-DtAGNOStS FUNCTtON.. ........
F3-16
OUTLINE ....................................
F3-16
SERVICE CODE NUMBERS..
......... F3-16
TROU8LESHOOTtNG GUtDE
........... F3-19
RELATIONSHtP
CHART.. F3-19 ..............
DIAGNOSTIC JNDEX
.................... F3-20
PRECAUTIONS
............................
F3-21
SYMPTOM TROUBLESHOOTING .... F3-22
TURBOCHARGERCONTROL
SYSTEM ......................................
F3-37
TURBOCHARGER F3-37 ........................
WASTEGATE SOLENOID VALVE.. .. F3-38
INTERCOOLER ............................
F3-39
FUELSYSTEM ..............................
F3-40
FUEL PUMP ................................
F3-40
FUEL PUMP RESISTOR/RELAY ......
F3-40
PRESSURE
REGULATOR .............. F3-41
INJECTOR ..................................
F3-42
INJECTOR RESISTOR
................... F3-42
PRESSUR REGULATOR CONTROL
SYSTEM ......................................
F3-43
SOLENOID VALVE (PRESSURE
REGULATOR CONTROL)
............. F3-43
CONTROL SYSTEM
....................... F3-44
PREPARATION ............................ F3-44
ENGINE CONTROL UNIT (ECU) ..... F3-45
7 3EOF3-301

SUPPLEMENTAL SERVICE INFORMATION .
I
The following points in this section are changed in comparison to the Mazda 323 4-Wheel Drive Work-
shop Manual [I 229-l O-89t].
Turbocharger
l Removal / Installation
Wastegate solenoid valve
l Inspection
htercooter
l Removal I Installation
Fuel pump (main)
l Inspection
Fuel pump resistor/relay
l System operation
l Inspection
Injector
l Inspection
l Volume test
Injector resistor
l Inspection
Pressure regulator control system
l Solenoid valve (pressure regulator control}
Engine control unit (ECU)
l Inspection 13EOF3.320
F3-I 5

F3 SELF-DIAGNOSIS FUNCTfON
SELF-DIAGNOSIS FUNCTION
OUTLINE
Theself-diagnostic function and diagnosis procedure are the Same as for the previous 4WD model. How-
ever, there is an additional service (malfunction) code (N0.35) for the new modet.
13EOF3-321
SERVICE CODE NUM8ERS
Sensor or
subsystem
NE-signal
G stgnal
Knock sensor I Malfunction display
Cond &ion Fail-safe
Service
code no. Output signal pattern
No NE-signal
ON
-
02
OFF
M
No G srgnal Cancels two-group injection ON
03
OFF
ml
Open or short circuit
pressure sensor
F3-16
--
I

SELF-DIAGNOSIS FUNCTION F3 I
Open or short crcuit
13EOFS322
Caution l If there is more than one failure present, the code numbers will be indicated in numerical or-
der, lowest number first.
l After repairing a failure, turn off the ignition switch, disconnect the negative battery cable,
and depress the brake pedal for at least twenty seconds to erase the service code from the
ECU memory. II
F3-17

F3 TROUBLESHOOTING GUIDE
SYMPTOM TROUSLESHOOTING
2 . CRANKS NORMALLY BUT WILL NOT START (NO COMBUSTION)
LIESCRIP-
l Engine cranks at normal speed but shows no sign of firing l Battery in normal condition
TION *Throttle valve not held fufly open while cranking (dechoke system not operating}
l Fuel in tank
UROOBLESHUOTlNG HINTS]
@ No spark
@.I low fuei tine pressure
l Ignition control malfunction @I Low engine compresslon l Ignition system component malfunction
@ No fuel injection
l Fuel pump inoperative l Ihjectors inoperative
;TEP
INSPECTION
I ACTION
1
Is strong btue spark visible at disconnected high- Yes Go to Step 3
tension lead?
NO Go to Step 2
2 Is “00” dlsplayed on Self-Dlagnosjs Checker
Yes
with ignltron switch ON? Check rgnltion system (Refer to
Troubleshooting “Misfire”)
c7 Section G
SYSTEM SELECT: 1 No
Service Code No. displayed Check for cause (Refer to specified
check sequence)
G- page
F3-16
“66” flashes
Check ECU termrnal 1F voltage
3 page W-45

Voltage: Battery vabage
(ignition switch ON)
W: SELF TEST C+ If OK, replace ECU
4 If not OK, check wiring
CT page F3-2
(ECU
- Self-Diagnosis Checker)
3
Connect diagnosis connector terminals F/P and
Yes
GND with jumper wire; IS fuel pump operating Does engine start in this condition?
sound heard wjth ignition switch ON?
4 If it does, check circuit-opening
relay
4 If it does not, go to Step 5
No Go to next step
F3-22
iTEF
6
8

F3 TROUBLESHOOTING GUIDE
I- STEP lNSPECTlON ACTION
Yes Go to Step 8
5 In same condition as in Step 2, IS fuel ilne pres-
sfire held after Igrxtbon swatch rs turned OFF?
Fuel line pressure: More than 147 kPa
Il.5 kgflcm’, 21 Psi 1 for 5 min.
6 In same condition as in Step 3, IS fuel line pres-
sure held after lgnltron switch IS turned OFF?
Fuel line pressure: More than 147 kPa
{ t.5 kgf/cm*, 21 psi) for 5 min.
No
I Go to next step
Plug both vcuum ports of pressure regulator; IS
fuel lme pressure held after ignltlon switch is
turned OFF? Yes Replace pressure regulator
r~ page F3-3
Fuel line pressure: More than 147 kPa
{ 1.5 kgf/crn*, 21 psi] for 5 min.
NO Check fuel pump hold pressure
e If OK, check InJector for fuel
leakage
e If not OK reptace fuel pump ZF- page F3-42
T page F3-3
8 Dlscofinect water thermosensor connector, does
engtne start? Yes Check water thermosensor
e ff OK. check connectrons of water
thermosensor and ECU 2Q terminal
Q If not OK, replace water thermo-
sensor
ET page F3-13
No 1 Go to next step --~
Is “00” drsplayea on Self-Diagnosis Checker
with ignition switch ON? 9 Yes Go to next step
NO Service Code No. displayed
Check for cause (Refer to specified
check sequence)
c7 page F3-16 SYSTEM SELECT, 1
“88” flashes
Check ECU terminal IF voltage
KIT page F3-45
Voltage: Battery voltage
(ignition switch ON)
e If OK, replace ECU
ET- page F3-2
e If not OK, check wiring
(ECU - Self-Diagnosis Checker)
Y %EtECT SW: A
Yes 1 Go to next step 10 Are rf ECU termrnaf voltages are OK?
(especjaffy 1C. 2D. and 2Q)
CT page F3-45
NO Check for cause
Yes Replace ECU
=T page F3-2
No Change to another brand of fuel
13EOF3 331 Try known good ECU, does condition improve?
CT page F3-2
F3-26

TROUBLESHOOTING GUlDE F3
7 CRANKS NORMALLY BUT HARD TO START - AFTER WARM-UP
*
l Engrne cranks at normal speed but requkres excessive cranking time before starting after running and being
DESCRIP- hot soaked
TION
l Battery rn normal condition l Engine starts normatly when cold
*Engine runs normally at Idle (If idle condrtron is not OK, refer to “Rough idle” ~Nos. 8-l 21)
[ ~ROUBLESHOOTLNG HINTS1
[ i 5 ArrlFuel mixture too Rich - l Fuel rqection control malfunction l lnpector fuet leakage
I
TEP tNSPECTlON @ Vaporlock
l Fuel pressure not held rn fuel line after engrne IS
stopped
l Pressure regulator control system malfunction
I ACTION
1 Is “00” dispiayed on Self-Diagnoses
Checker wrth rgnrtron switch ON7
SYSTEM?_SELECT. 1
SELECT SW. A
Remove vacuum hose from pressure regulator
(port A) ancI plug rt. dOt?S engine start normally’-,
Remove both vacuum hoses from pressure regu-
lator (ports A and Bj and plug them; does en-
gine start normally7
@
PtUG
/ /
Are ECU terminal voltages OK
(especially 1 C, 20, 20 and 2T)?
w page F3-46 Yes Go to next step
No Service Code No. displayed
Check for cause (Refer to specified
check sequence) CT oaae F3-16
“88” flashes
Check ECU terminal 1F voltage
Voltage: Battery voltage
(ignition switch ON) w page F3-45
( cs> It OK. replace ECU
/ w page F3-2’
3 If not OK, check wlrtng
(ECU - Self-Dlagnosrs ChecKer)
Yes Check pressure regulator control sys-
.
tern (high temperature operation) w page F3-43
I NO Go to next step
Check pressure regulator control sys-
tem (low temperature operation)
No 1 Go to next step
Yes Go to next step
NO Check for cause
F3-27

TROUBLESHOOTING GUIDE F3
8
1 ROUGH IDLE/ENGINE STALLS AT IDLE - ALWAYS
DESCRtP- 1 l Engine starts normally but stalls or vibrates excessively at idle in every condition
TION
[TROUBLESHOOTiNG HlNTSJ @ Air/Fuel mixture tw lean @ Incorrect idle-speed l ldiespeed misadjustment l Idle-speed control malfunction
$I One or more spark plugs not firing
9 Low engine compression
B Airflow meter stuck l Air leakage l Fuel injection control malfunction
*Low fuel line pressure
@ One or more injectors clogged or not
@ Low intake air amount operating
INSPECTION
Is “00” displayed on Self-Diagnosis
Checker with ignition switch ON?
1
SYSTEM SELECT: 1
ACTION
Go to next step
Service Code No. displayed Check for cause (Refer to specified
check sequence) c7 page F3-16
“88” flashes
Check ECU terminal IF voltage
(17 page F345
--.
‘\.
Voltage: Battery v&age
(Ignition switch ON)
4 If UK, replace ECU IT page F3-2 c3 If not OK, check wiring
(ECU - Self-Diagnosis Checker) Y -SELECT SW: A
Are ECU terminal voltages OK
(especially 20, 20, and ZQ)?
D page F3-45 Yes
Gu to next step
NO Check for cause
Disconnect each high-tens&on lead at idle: does
engine speed decrease equally at each cylindeR Yes Go to Step 9
NO Go to next step
Is injector operating sound heard at idle? [ Yes Go to Step 7
t- NO Stop engine and go to next step
Yes Check if injector resistance is OK
CT page F3-41 Is there battery voltage at each injector connec-
tor (No.1 (P), No.2 (R), No.3 QV), No.4 (0)) with
ignition switch ON?
Resktance: Approx. 2.110
(at 20*C [68*F))
4 if it is, check wiring
(ECU - Injector)
c3 If it is not, replace itijector
Go to next step
NO
Is there battery v&age at injector resistor (W/R)
I .Yes
with ignition switch ON? Check mjeotor resistor
4 tf OK, check for short circuit in wir-
ing (Injector resistor-Injector)
e3 If not OK,’ replace injector resistor
Check for open circuit in wiring (Main
relay (FUEL INJ relay)-Injector resistor)
Go to next step
t NO 1
Is strong blue soark visible at each disconnected Yes
‘Check ‘high-tension lead
4 If UK. check distributor cap and
rotor .
c3 If not OK, replace high-tension lead
‘-F3-29

TROUSLESHOOTING GUIDE F3
10 ROUGH IDLE/ENGINE STALLS AT IDLE - AmER WARM-UP
DESCRIP- -Engine runs normalty at idle during warm-up but engine stalls or vibrates excessively after warm
TlO#
TROUBLESHOOTING HINTS]
3 Idle-speed control system malfunction
3 Air/Fuel mixture too lean
l Air leakage
*Low fuel line pressure
TEP
INSPECTION
1
ts “00” dlsplayed on Se\-Diagnosis Checker
with ignition switch ON?
SYSTEM SELECT: 1 @ Air/Fuel mixture too rich
l Fuel injection control malfunctlon
(correction for coolant tem$eratuie)
@ Poor ignition
@ Low engine compresslon
ACTION
YES Go to next step
No Service
Code No. displayed
Check for cause (Refer to specified
check sequence)
w page F3-16
“88” flashes Check ECU terminal IF voltage w page F345
Voltage: Battery voltage
(ignition switch ON)
W: SELF TEST e !f UK, replace ECU
w page F3-3 c3 ff not OK, check wiring
(ECU - Self-Diagnosis Checker)
2 Are ECU termrnal voltages OK Yes Go to next step
(especially 20, 20, and 2Q)?
w page F3-45 No
Check for cause
3 Disconnect each high-tension lead at idle; does Yes Go to next step
engine speed decrease equally at each cylinder?
NO Go to Step 9
4 Is intake manifold vacuum correct at idle? Yes Go to next step
Vacuum: More than 450 mmHg f 17.7 InHg )
NO Check for air leakage of intake air sys-
tem components
5 Is air cleaner element clean? Yes Go to next step
No Replace air cleaner element
F3-3 1