water pump MAZDA 323 1992 Workshop Manual Suplement

SCHEDULED MAINTENANCE SERVICES A
SCHEDULED MAINTENANCE SERVICES
MAINTENANCE TABLE
Chafi symbols:
1 : Inspect: Visual examination and/or functional measurement of system’s operation or
performance , A: Adjust: Examination resulting in adjustment or replacement
n
R: Replace or change
T: Tighten
REMARKS
After 80,000 km or 48 months, continue to follow the described maintenance at the recommended intervals.
As for * marked items in this maintenance chart, note the following points.
+ 1 Major service interval at 12 months/20,000 km (12,000 miles).
Lubrication service based on distance only 10,000 km (6,000 miles) not time.
l 2 Adjust or inspect alternator and water pump drive belt, and power steering and air conditioner drive belt
if equipped.
‘3 Replacement of the timing belt is required at every 100,000 km (60,000 mile). Failure to replace the tim-
ing bett may result in damage to the engine.
‘4 tf the vehicle is operated under any of the following conditions, it is suggested that the engine oil and
oil filter be changed more often than the recommended intervals.
a) Driving in dusty conditions. I
:
b) Extended periods of idling or low speed operation. i
i!
c) Driving for a prolonged periods in cold temperatures or regularly driving onty short distances.
*5 If the vehicle is operated in very dusty or sandy areas, inspect and, if necessary, replace more often
than at usual recommended intervals.
l 6 This IS a full function check of all electrical systems, i.e, atl
ltghts. washers (including condition of blades)
electric windows, sunroof, horn etc.
‘7 Replace every two years. $1
‘I
If there has been continuous hard driving, mountain
drivtng, or if the brakes are used extensively or the
vehicle is operated in extremely humid climates, the brake fluid should be changed annually.
Emission Control and Related Systems
The ignition and fuel systems are vitally important to the proper operation of the-emission control and relat-
ed system, as well as for efficient engine operation. It is strongly recommended that all servicing related
to these systems be done by your Authorised Mazda Dealer.
13EOAX-302 -4
I!
A-3

The following chart shows interchangeability of the main parts of the previous BP DOHC Turbo engine
and the new BP DOHC Turbo engine for 4WD models.
S ymiols: 0 _. lnterc hangeable X . . . Not Interchangeable
Part name tnterchangeability
Remark
Cytlnder head 0
Camshaft 011 seal 0
Cvllnder head bolt 0
CB :
Cyh nder
blcck
related
Crankshaft
related
Timing belt
related
Valve
related
Lubrication
system
related Cylrnder head gasket 0
Wnder head cover 0
Cylinder head cover gasket
Cylinder block
MaEn bearina cao 0
0
0
Ma+n bearino suo~oFt elate I
0 I ” ,I I
Oil pan
Timrno belt cover I X
0 I
Turbocharger oil return pipe hole increased from
13mm IO.51 in) to 17mm IO.67 in)
Seal elate
Front orl seal I 0 I
I I 0
1
Rear 011 seal 0
Crankshaft 0
Marn bearina 0
Thrust bearing
Connectmg rod
Connecting rod beartng
Piston 0
;J
X
Shape different
Piston skirt shortened
I Piston pm cl
Tw
X Sectional shape different
Piston rrng Piston ring end gap increased from 0:?5--0.30mm
Second
X ~0.006-0.011 in ) to 0.35-0.50mm IO.01 4-0.019
in ] (Measured In cylinder)
Crankshaft pulley Shape different
Rear cover ;5
Flywheel
I 0
Flywheel bolt 0
Tbmlng belt 0
Timing belt crank pulley 0
Camshaft pulley 0
Timing belt tensioner and spring
0
Idler 0
Camshaft 0
AA
Valve Intake
Exhaust
cl
0
X Metallic sodium-filled valve
Valve spring Intake
I 0
and seat
Exhaust 0
Vatve wide I 0
Valve seal
Oil pump 0
Oil pump gasket 0
oil strainer 0
Oil strainer gasket 0
Oil cooler
X Heat dissi patlon capacity increased
Oil jet
Oil filter Shape different
1 Water pump 0
Coohng Thermostat 0
system
related Radiator 0
Cooling fan 0
I 3EO32.304
BZ-3.

B2 CXJTUNE
CRANKSHAFT PULLEY
ALTERNATOR, WATER PUMP V-RIBBED BELT PULLEY
/TORSIONAL DAMPER
P/S, A/C V-RI3BED BELT PULLEY
ALTERNATOR DRIVE PULLEY
Deflectton (98 N ( 10 kgf, 22 Ibf f ) mm ftn)
Owe belt New Used. Lrmlt
Alternator 5.5-7.0 6.0-7.5 8.0
{0.22-0.27 ) IO.24-0.29) to.31 )
fension
Owe belt
Alternator New
460-660
(46-68,
llO--140) Used
400-580
{‘IO-60,
88-130 1 N I kgf, Ibf]
Ltmit
340
135, 771
l The alternator and water pump pulleys are changed to V-ribbed type for improved performance l With the adoptjon of the V-ribbed betf. the belt adjustment specifications are changed.
B2-6

F3 OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
Theefuel and emission control system of the new 323 4WD model 1s basically the same as that of the prevr-
ous 323 4WD model; however some parts are changed. The changed parts and interchangable parts
are shown betow.
13EOF3-304
Changed parts
1 ~ components Contents and purpose Reference pagl
INTAKE AlR
SYSTEM Turbocharger
Intercooler
l Size Increased for greater boost pressure l Wastegate solenord valve IS lozated on Intake port of F3-10
turbocharger to make system more compact F3-37
Volume increased for Improved F3-10
t F3-39
Wastegate sojenold valve
l Wastegate solenoid valve changed to duty solenoid
type for Increased engine power and response
l Wastegate solenoid valve is located on Intake port of
turbocharger to make system more compact F3-1 f
F3-38
I r
Pressure regulator One-stage operattlon changed to two-stage operatron F3-14
to improve hot restarting f3-41
L
FUEL SYSTEM High-ohmic type change to low-ohmrc type with exter-
Fuel qector na solenoid reslstor for improved fuel supply during F3-12
high-speed driving F3-42
Fuel pump reslstor Resistance reduced for
surer fuel supply F3-40
CONTROL
SYSTEM Pressure
regulator control system
Atr flow meter Two-stage operatton used to Improve hot restarting
Measures larger amount of air flow Increased power
Resistance values changed F3-t4
F3-43
F3- 9
f3EOF3-305 lnterchangable parts
tntake air system
l
Air valve
l Air bypass valve
l Air cleaner
l Air cleaner element
Fuel system
l Fuel filter assembly
l Fuel pu.mp (transfer
l Fuel vapor valve Control system
. l Throttle sensor
l Water thermosensor
l Knock sensor and control unit
l Oxygen sensor
l Fuel pump control unit
l Main relay
l Circuit opening relay
l Check valve (two-way) .
Evaporative system
l Charcoal canister
l Check valve (two-way)
13EOF3-306
F3-4

CHECK VALVE SOLENOID VALVE
(PURGE CONTROL)
llll
*
SOLENOID VALVE
(PRC LOW TEMP.)
3 ~NTERCOOLERII’ I ,‘/ I
II II
’ f frrmvmlHHt-----lHt I -1 II II
IIt - --M:l, i -KNmK~[I~ ,
’ ISC VALVE
VALVE WATER CHAkCOAL
CANISTOR
CHECK VALVE
I FUEL FUEL FILTER
PUMP
I FUEL FILTER
TRANSFER
PUMP
AIRkLOW METER
(WITH INTAKE AIR THERMOSENSOR)
DISTRIBUTOR
CATALYTIC CONVERTER
l TO ENGINE CONTROL UNIT

F3 TROUBLESHOOTING GUIDE
I- STEP lNSPECTlON ACTION
Yes Go to Step 8
5 In same condition as in Step 2, IS fuel ilne pres-
sfire held after Igrxtbon swatch rs turned OFF?
Fuel line pressure: More than 147 kPa
Il.5 kgflcm’, 21 Psi 1 for 5 min.
6 In same condition as in Step 3, IS fuel line pres-
sure held after lgnltron switch IS turned OFF?
Fuel line pressure: More than 147 kPa
{ t.5 kgf/cm*, 21 psi) for 5 min.
No
I Go to next step
Plug both vcuum ports of pressure regulator; IS
fuel lme pressure held after ignltlon switch is
turned OFF? Yes Replace pressure regulator
r~ page F3-3
Fuel line pressure: More than 147 kPa
{ 1.5 kgf/crn*, 21 psi] for 5 min.
NO Check fuel pump hold pressure
e If OK, check InJector for fuel
leakage
e If not OK reptace fuel pump ZF- page F3-42
T page F3-3
8 Dlscofinect water thermosensor connector, does
engtne start? Yes Check water thermosensor
e ff OK. check connectrons of water
thermosensor and ECU 2Q terminal
Q If not OK, replace water thermo-
sensor
ET page F3-13
No 1 Go to next step --~
Is “00” drsplayea on Self-Diagnosis Checker
with ignition switch ON? 9 Yes Go to next step
NO Service Code No. displayed
Check for cause (Refer to specified
check sequence)
c7 page F3-16 SYSTEM SELECT, 1
“88” flashes
Check ECU terminal IF voltage
KIT page F3-45
Voltage: Battery voltage
(ignition switch ON)
e If OK, replace ECU
ET- page F3-2
e If not OK, check wiring
(ECU - Self-Diagnosis Checker)
Y %EtECT SW: A
Yes 1 Go to next step 10 Are rf ECU termrnaf voltages are OK?
(especjaffy 1C. 2D. and 2Q)
CT page F3-45
NO Check for cause
Yes Replace ECU
=T page F3-2
No Change to another brand of fuel
13EOF3 331 Try known good ECU, does condition improve?
CT page F3-2
F3-26

F3 TROUBLESHOOTING GUIDE
3TEI ACTION
Is fuel line pressure correct at Idle?
*
Fuel line pressure: 265-314 kPa
12.7-3.2 kgf/cm’, 38-46 psi]
(Two vacuums hose to pressure regulator
disconnected)
304-392 kPa [ 3.1-4.0 kgf/cm’, 44-57 psi 1
(Upper vacuum hose to pressure regulator
disconnected)
INSTALL CLAMPS Yes Go to next step
No Low pressure
Check fuel line pressure while pinching
fuel return hose
4 If pressure quickly Increases,
check pressure regulator
e If pressure gradually Increases,
check for clogging between fuel
pump and pressure regulator
If hose is not clogged, check fuel
pump maxrmum pressure
Connect System Selector to diagnosis connector
and set Test Switch to SELF TEST; is ignition
tlmlng at idle correct after warm-up?
Ignition timing (BTDC): 10 f lo Yes Go to next step
No Adjust tgnrtkon system
8 Dtsconnect water thermosensor connector; does
engine condrtlon Improve? Yes Replace water thermosensor
No
Try known good ECU. does condltlon
Improve?
w page F3-13
Go to next step
Check if injector resistance is OK
w page F3-42 9 Is jqector operating sound heard at Idle?
Yes
No
Resistance: Approx. 2.11 Q
(at 20°C 168*F])
4 If it is, check wlnng
(ECU - Injector)
c3 If it Is not, replace injector
Go to next step IO
Yes Is engine compressron cprrect?
w Section G
No
Engine compression:
1059 kPa 110.8 kgf/cm2, 152 psi)-300 rDm
is strong blue spark vrslble at each disconnected
hrgh-tension lead?’ Check engine
3 Section B2
17
Yes Go to next step
No Check high-tension lead
w Section G
c3 If UK, check distrrbutor cap and
rotor
3 If not OK, replace htgh-tensron lead
Try known good ‘ECU: does condrtron
Improve7
w page F3-3 12 Are spark plugs.OK?
w Section G
l Wear and carbon butld up l Piug gap l Damage Yes
NO
Clean, adjust
13EOi3.334
F3-32.

TD TECHNICAL DATA
LU8RlCATtON SYSTEM
Item
Lubricating method
011 pump Engine
BP DOHC turbo
Force-fed
6 . Trochoid gear
Relief pressure
kPa I kgf/cm’. psi] 343-441 [ 3.5-4.5, 50-64 1
Regulated pressure kPa { kgf/cm’ , psi ] -rpm
294-392 { 3.0-4.0, 43--57.1.3,000
Inner rotor tooth tip to outer. rotor Standard
0.02-0.16 (OJOOS-O.O063]
clearance
mm {in]
Maximum I
0.20 [ 0.0078 )
Outer rotor to body clearance
Side clearance
Oil fIl!er
, TYpe
Relief pressure differential . mm [in) Standard
Maximum
mm {in) Standard
Maximum 1
kPa’ f kgf/cm’, psi 1 0.09-0.18 ~0.00354.Ofl71]
0.22 { 0.0087 1
0.03-0.11 ~0.0012-0.0043~
0.14 {0.0055)
Full-flow, paper element
. 78-118 (0.8-1.2. 11-17) Srade
----l-in
Viscosity
num her
Item
Cooling metha
Water pump
, We
Impeller diame
Number of imf
Speed ratio -
Water seal !$
Thermostat
Jype. _
Opening terq
/Full-open
1 F&open lift
I
Antifreeze E
TD-4

TECHNICAL DATA TD
Engine
Item BP DOHC turbo
Engine oii
Total (dry engine} 4.0 14.2, 3.5)
Capacity
L IUS qt, Imp qtl Ott pan 3.6 (3.8, 3.2)
011 filter 0.17 (0.18, 0.15)
Grade API Service SD, SE, SF or SG
Above 30°C (86*F) SAE 40
O*C-40*C ~32°F-1040F 1 SAE 30
-1 OOC--2O*C [ 14OF-68OF ] SAE 2OW-20
Viscosity Above -10% [14*Fj SAE ZOW-40 or 2OW-50
number -25*C--3O*C I-1 3OF-86OF ] SAE 1 OW-30
Above -25OC (-13*F1 SAE low-40 or low-50
Below O*C (32*F] SAE 5W-30
Below -2O*C I-4*F] SAE 5W-20
COOLING SYSTEM
L
item
Zooling method - 1 Engine
BP DUHC turbo
I Water-cooled, forced crrcutation
water pump
Type
mpeller diameter
Number of impeller blades
Speed ratio
tiater seal type
rhermostat
bfpe
Opening temperature
Full-open temperature
Full-open lift mm [in)
OC (OF)
*C j*FJ
mm (in] Centrifugal, V-belt driven
75 12.95)
6
1 : 1.05
Unified mechanical seal
Wax, two-stage
Marn: 86.5-89.5 [ 788-I 93 1
Sub: 83.5-86.5 [182-i 88)
loo (212)
Main: 8.0 (0.31 1 min.
Sub: 1.5 IO.061 min.
Radbtor
Type
Cap valve opening pressure kPa { kgflcm2, psi)
Cooling circuit checkrng pressure kPa ( kgflcm2, psi 1
Cooling fan
Type
Number of blades
Outer diameter mm {in 1
Capacity w-v
Current A
Water thermoswitch
OFF-+ON “C 1°F) 1
Radiator thermoswitch
OFFdON OC (OF]
Coolant
Capacity LWS qt,
Imp qt) Coolant protection
Above -16*C (3OF]
Antifreeze solutron
.Above -26*C t-1 5*F ) -
Above -4UOC I-40°F) Corrugated fin
74-103 {0.75--1.05, 11-15)
103 11.05, 15)
Electric
5
340 (13.41
160-12
Hi: 13.3+ 10% max., Lo: 8.8+ 10% max.
97 f207)
105 [221)
6.0 16.3, 5.3)
Specific gravity at 20*C (68*f)
1.054
1.066
1.078 -.ep
1

TO TECHNICAL DATA
FUEL AND EMISSION CONTROL SYSTEMS
Item.
Idle speed
tgf-don trrmng-
Fuel pump
MaxImum output pressure
Transfer pump
Maximum output pressure
Fuel filter Engine
rPm
BTDC
kPa [ kgf/cm2, psi 1 1
kPa { kgflcm2, PSI ) 1 BP OUHC turbo
800 f 50
10 l 10
490-736 (5.0-7.5, 71-1 IO]
39 10.4, 5.7 ) or higher
I Type
Low-pressure side Nylon element (in fuel pump)
Hiah-Dressure side PaDer element
Pressure regulator
Regulating low kPa ( kgflcm2, psr 1 265-314 (2.7-3.2, 38-46 1
pressure High kPa { kgflcm2, psr 1 304-392 (3.1-4.0, 44-57 1
lniector
_ Type Low-ohmic
Type of drive
Electromechanical
Resistance q
Approx. 2.11 Q (at 20% ( 68*f )]
lniector reslstor
L - Resistance/injector
Idle-speed control (tSC) valve
TvDe n 1 6 [at 20°C 168OFjj
I Rotarv
Resistance
Solenoid valve (purge control)
Resbstance
Solenoid valve {wastegate)
Resistance n(
R I
i-l I 1 t-13 [at ZO*C {68OF j]
23-27 tat 20°C l68OFll
. r.
33-39 lat 20°C I68OF 11
Solenoid valve (PRC)
Resistance Low temp. q
33-39 [at 2O*C {SS*F]]
High temp. 0 1 33-39 [at 20°C (68OF]]
Water thermosensor
-20°C ( -4OFJ 1 14.6-17.8
Resistance kQ 2o”c I 68OF) 2.21-2.69
40°C ( tO4OF) 1.0-l 3
80°C I176OFJ 0.29-0.35
Airflow meter
Resistance R E244Vs
E2*Vc Fuity closed
Fully open I 20-600
20- 1,000
200-400
EP++THAA
(intake air
thermosensor) -2O*C ( -4OFj 1 13,600-l 8,400
20% 1 68OF) 1 2,210-2,690
6O*C 114OOFl i 493-667
EI ~Fc
I Fully closed 00
0 1
Oxygen sensor (ceramic beater coil)
Resistance
Fuel tank Approx. 6 [at 20°C f68OF)]
I CaDacW L I US oal. ImD aal I I 60 I 15.9, 13.2 I
I
Air cleaner
Element type
Fuel
Specrficatioir Oil permeated
Unteaded premium (RON 95 or higher)
l TEN terminal of diagnosis connector grounded. .
-
ENGINE ELI
3attery
I
Dark current’
Alternator
Starter
Distributor qr
Ignition timin?
ffEN terminal
Ignition coil
Spark plug
l ’ Dark current
r2 Standard pl