change time MAZDA CX90 2024 Owner's Manual

Immediately after switching to
daylight savings, charging may occur
at the charging timer time set before
the switch to daylight savings until
the vehicle power is switched ON.
Edit
Function Available setting
changes
Start Time
Select the desired charging
start time. Time
(10-minute inter- vals)
End Time
Select the desired charging
end time. Time
(10-minute inter- vals)
Repeat
Select the day(s) of the
week to repeat. Monday
― Sun-
day
Charge Limit
Select the desired charge
limit method. According to Bat-
tery Charge Level, According to Esti- mated Range
Battery Charge Level
*1
Select the desired maxi-
mum charge level. 100%
― 20%
(9 levels)
Estimated Range
*2
Select the desired estimat-
ed range. In 10 km (10 mi)
increments
*1 Can be changed when According to Battery
Charge Level is selected for Charge Limit.
Use when you want to charge only the
amount of charging you need. This helps you
save power and prevent high voltage battery
deterioration.
*2 Can be changed when According toEstimated Range is selected for Charge
Limit.
Use when you want to charge according to
your planned driving distance.
The distance-to-full discharge changes
depending on the driving conditions and
surrounding environment. Check the actual
remaining distance-to-full discharge.
If you change the distance unit after setting
the Estimated Range, the Estimated Range
will be calculated in the unit after the
change. (If you change the units to miles
after setting the estimated range to 100 km,
the charge distance will be for 60 miles.)
NOTE
A charging day is set using Repeat
If 1 repeat day is set, charging is
repeated every week on the set day
of the week.
Depending on the set days of the
week, the Repeat indication is
displayed as Weekdays, Weekends,
and Daily. Otherwise, it is displayed
as Custom.
Setting example
Function Available setting
changes
Start Time 21 : 00
End Time 6 : 00
Repeat Friday
Charge Limit According to Bat-
tery Charge Level
Battery Charge Level 80%
In this case, charging is done every
week from Friday at 21 : 00 hours to
Saturday at 6:00 hours. However, if
the Battery Charge Level reaches
80%, the charging is stopped even if
it is before the End Time.
No day is set using Repeat
If no Repeat day is designated,
charging is done only 1 time at the
set hours.
Setting example (if settings below are
made at 13 : 00 hours)
Function Available setting
changes
Start Time 12 : 00
End Time 18 : 00
Driving
Charging
5-119
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

FunctionAvailable setting
changes
Repeat Once
Charge Limit According to Esti-
mated Range
Estimated Range 50 km (30 mi)
In this case, when the charge
connector is connected, charging
starts immediately for charging to
18 : 00 hours on the same day.
However, if a charging amount
allowing a 50 km (30 miles) trip is
reached, the charging is stopped
even if it is before the end time.

Setting example (if settings below are
made at 13 : 00 hours)
Function Available setting
changes
Start Time 1 : 00
End Time 8 : 00
Repeat Once
Charge Limit According to Bat-
tery Charge Level
Battery Charge Level 100%
In this case, charging is done from
the next day at 1 : 00 hours to 8 : 00
hours. However, if the Battery
Charge Level reaches 100% is
reached, the charging is stopped
even if it is before the End Time.

Charge When Connected
Cancels charging schedule to allow im-
mediate charging.
1. Select Settings from the home screen on Mazda Connect.
2. Select EV Settings from the setting
screen.
3. Select Charge When Connected from the selection screen.
Available setting changes
Enable, Disable
NOTE
The charging timer can also be
canceled on the screen displayed on
the center display when the vehicle
power is switched OFF.
When the charging is completed
using the Charge When Connected
setting, the charging timer schedule
is restored.

Charge Limit for AC Charging
Sets the charge limit when using an AC
charger.
1. Select Settings from the home screen on Mazda Connect.
2. Select EV Settings from the setting
screen.
3. Select Charge Limit for AC Charging from the selection screen.
Available setting changes
100% ― 20% (9 levels)
NOTE
For normal charge, set the maximum
charge limit of the high voltage battery.
Set the Battery Charge Level of the
charging timer for each charging timer
setting.

Driving
Charging
5-120
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Climate control timer
The climate control timer is a function
which operates the cooling or heating
system automatically according to a
preset time. The power consumption
of the air conditioner after starting to
drive the vehicle is reduced by
operating the air conditioner and
providing a comfortable temperature
in the cabin before driving.
Refer to Convenient Ways to Use the
Fully Automatic Air-Conditioning on
page 6-12.
Charge Connector Lock
The charge connector lock is a function
which locks the charge connector con-
nected to the vehicle so that it cannot
be pulled out. You can also select the
lock conditions for the charge connec-
tor according to locations and situa-
tions.
1. Select Settings from the homescreen on Mazda Connect.
2. Select EV Settings from the setting screen.
3. Select Charge Connector Lock from the selection screen.
4. Set the lock condition from the se- lection screen.
Available setting changes
Locked When Charging
Unlocks connector when charging is complete
or vehicle is unlocked.
Locked When Connected
Unlocks connector only when vehicle is un-
locked.
Available setting changes
Off
Charge connector remains unlocked at all
times.

Functions using a Smartphone
You can check the remaining high
voltage battery power, operate the
charging, and operate the air
conditioner remotely by a Smartphone
remote control operation using the
Connected Service. For details, consult
an Authorized Mazda Dealer.
Driving
Charging
5-121
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

NOTE
The screen display ends after a certain
period of time has passed since the
sign was displayed on the screen.
Tu r n i n g off the TSR
The TSR can be turned off using the
Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Convenient Ways to Use
the Traffic Sign
Recognition System (TSR)
You can set an excessive speed
warning to be issued when your
vehicle's speed exceeds the speed
indicated on the speed limit sign.

Turn on the excessive speed warning
using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.

If your vehicle’s speed exceeds the
speed on the speed limit sign, the area
around the display of the speed limit
sign flashes in amber
and a warning
sound is activated. In addition, if the
vehicle speed continues to be
excessive, it stops flashing and remains
on.
NOTE
The warning pattern and the warning
activation timing can be changed using
Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Driving
Tra ffi c Sign Recognition System (TSR)
5-152
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

Active driving display
The CTS is temporarily canceled
Constant speed/Headway control function
If any of the following conditions is met, the constant speed/headway control
function is temporarily canceled.
The brake pedal is depressed.The CANCEL switch is pressed one time.The DSC has operated.The Smart Brake Support (SBS) has operated.The front radar sensors cannot detect target objects.The parking brake is applied.Any door is opened.The driver’s seat belt is unfastened.The frequency of the braking operation by the CTS is high.
If the constant speed/headway control function is temporarily canceled, it will
resume operation at the previously se t speed by pressing the RES switch.
Steering assist function
If any of the following conditions is met, the steering assist function is temporarily
canceled. The steering assist function is automatically restored when its operation
conditions are met.
The constant speed/headway control function is canceled.White (yellow) lane lines cannot be detected or a vehicle ahead cannot be
recognized.
The turn signal lever is operated.The steering wheel is operated abruptly.Hands are off the steering wheel.The vehicle is making a sharp curve.The vehicle crosses a lane line.The width of the vehicle lane is narrow or wide.
NOTE
The notification method when the steering assist function is canceled can be
changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
Driving
Cruising &
Tra ffi c Support (CTS)
5-186
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

1. “BRAKE!”

Active driving display
1. “BRAKE!”
NOTE
If any of the following conditions is
met, the forward detection function
may not operate normally.
The Forward Sensing Camera (FSC)
cannot detect target objects.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
The front radar sensor cannot
detect target objects.
Refer to Radar Sensors on page
5-131.
When there is the possibility of a
partial contact with a target object.
The driver deliberately performs
driving operations (accelerator pedal
operation, steering wheel operation,
selector lever operation, and turn
signal lever operation).
If any of the follo wing conditions is
met, the forward detection function
may operate.
An animal or object on the road is
detected.
Passing an approaching vehicle
while rounding a curve.
Vehicle is passing through a narrow
gate or a gate with a low ceiling.
There is a metal object, bump, or a
protruding object on the road.
(Vehicles with Driver Monitoring
(DM))
If the system determines that the
driver is not paying attention to the
road, it activates the collision
warning earlier than normal.
If the forward detection function
performs brake control and the
vehicle is stopped, the system will
continue to hold the brakes for a
brief time unless there is an
operation performed by the driver.
The operation distance and volume
of the collision warning can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
The Turn-Across Tra ffi c operation
conditions*
The Turn-Across
Tra ffi c operates when
all of the following conditions are met.
The vehicle speed is about 4 km/h
to 20 km/h (3 mph to 12 mph).
The left turn signal light is turned on
and the vehicle is turning left.
A lane line between your vehicle and
the vehicle approaching in the
opposite direction is detected.
The system determines that there is a
possibility of collision with an object
ahead.
When the Turn-Across Tra ffi c operates,
the driver is notified of the danger by
the screen display and warning sound.
Furthermore, if the possibility of a
collision increases, brake control is
performed.
Instrument cluster
Driving
Smart Brake Support (SBS)
*Some models.5-201
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Operating Each Switch
AUTO switch
Automatically controlled according to
the set temperature.
Temperature setting switch
How to increase the set temperature
How to decrease the set temperature
NOTE
The set temperature changes in
increments of 0.5 ℃ within a range
of 15 ℃ (60 °F) and 29 ℃ (84 °F).
The set temperature can be quickly
adjusted by pressing and holding the
temperature setting switch.
When the temperature is set to the
lower or upper limit, “Lo” or “Hi” is
displayed.
SYNC (synchronized temperature)
switch
The mode switches between
independent mode and
interconnection mode each time the
switch is pressed.
Equipment to Make Cabin More Comfortable
Fully Automatic Climate Control (Front)
6-8
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Independent mode (indicator light
turned off)
The set temperature can be controlled
independently for the driver's side and
front passenger's side.
Press the driver’s side temperature
setting switch or the front passenger’s
side temperature setting switch to
control the temperature.
Interconnection mode (indicator light
turned on)
The set temperature for the driver's
side and front passenger's side is
controlled simultaneously.
Press the driver's side temperature
setting switch to control the
temperature.
NOTE
The set temperature for the front
passenger's side and the rear (while
the rear climate control system is
ON) changes to that of the driver
when independent mode is switched
to interconnection mode.
When the front passenger’s side
temperature setting switch or the
rear temperature setting switch is
pressed while in interconnection
mode (SYNC switch indicator light
turned on), the mode switches to
independent mode (SYNC switch
indicator light turned off).
A/C switch
The cooling/dehumidifying function
switches between on and off each time
the switch is pressed. The indicator
light turns on while the function is
operating.
NOTE
The air conditioner may not operate
when the ambient temperature falls to
nearly 0 ℃ to protect the system.
Rear window defogger switch
Use to defog the rear window.
Refer to How to Use the Rear Window
Defogger Switch on page 5-79.
Air intake selector switch
The mode is switched between
recirculate mode and fresh air mode
each time the switch is pressed.
Equipment to Make Cabin More Comfortable
Fully Automatic Climate Control (Front)
6-9
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The display indicates whether
recirculate mode (
) or fresh air
mode (
) is selected.
WARNING
Do not recirculate the air in the cabin
during cold or rainy weather.
Recirculating the air in the cabin during
cold and rainy weather is dangerous as
it will cause the windows to fog up.
Your vision will be hampered, which
could lead to a serious accident.
Recirculate mode (
)
Outside air is shut off. Air within the
vehicle is recirculated. Use this
position when going through tunnels,
driving in congested traffic (high engine
exhaust areas) or when quick cooling is
desired.
Fresh air mode (
)
Outside air is allowed to enter the
cabin.
Use this mode for ventilation or
windshield defrosting.
NOTE
The recirculated air position is the
default position whenever the
ignition is switched ON, the climate
control system is on, and the outside
temperature exceeds about 73 °F
(23 ℃).
To exit the default recirculated air
position, press the air intake selector
switch to select the outside air
position.
When the air intake selector switch is
set to the outside air position and
the outside temperature exceeds
about 73 °F (23 ℃), the climate
control system may automatically
select the recirculated air position to
improve the efficiency of the climate
control system.
Mode selector switch
The desired airflow mode can be
selected.
The mode changes each time the
switch is pressed. The selected mode is
indicated on the display.
NOTE
To set the air vent to press the
windshield defroster switch.
Fan control switch
How to increase the airflow amount
Equipment to Make Cabin More Comfortable
Fully Automatic Climate Control (Front)
6-10
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

How to decrease the airflow amount
The airflow amount changes each time
the switch is pressed. The airflow
amount is indicated on the display.
The airflow amount can be adjusted to
7 levels.
Climate control system power switch
(system on/off)
Switches the climate control system on
and off.
The indicator light turns on while the
function is operating.
Windshield defroster switch
Use to defrost the windshield and front
windows.
Automatically switches to fresh air
mode. The indicator light turns on.
WARNING
Do not lower the airflow temperature
when defrosting the windshield.
Otherwise, the outer side of the
windshield will frost causing reduced
visibility which may lead to an
accident.
NOTE
For faster defrosting , do any of the
following operations.
Operate the fan switch and
increase the airflow amount.
Press the temperature setting
switch to increase the airflow
temperature.
Be careful that the windows do not
fog up when doing any of the
following operations.
Switch to recirculate mode.Tu r n o ff t h e a i r co n d i t i o n e r.
Equipment to Make Cabin More Comfortable
Fully Automatic Climate Control (Front)
6-11
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04