service reset MAZDA MIATA 1991 Factory Service Manual

ADJUSTMENTS
AIRFLOW MODE DOOR
Set airflow mode control lever to vent position. Disconnect control cable at airflow mode door lever. Extend
airflow mode door lever until it stops, and hold it there. See Fig. 1
. Attach control cable to door lever and clip.
Ensure control lever moves freely between defrost and vent positions.
AIR-MIX (TEMPERATURE BLEND) DOOR
Set temperature control lever to maximum hot position. Disconnect control cable at air-mix door lever. See Fig.
1 . Extend air-mix door lever until it stops, and hold it there. Attach control cable to door lever and clip. Ensure
control lever moves freely between hot and cold positions.
RECIRCULATED/FRESH AIR DOOR
Set recirculated/fresh air control lever to fresh position. Disconnect control cable at recirculated/fresh air door
lever. Retract recirculated/fresh air door lever until it stops, and hold it there. Attach control cable to door lever
and clip. Ensure control lever moves freely between recirculated air and fresh air positions.
TESTING
BLOWER MOTOR CIRCUIT
1. Check 30-amp HEATER circuit breaker in passenger compartment fuse panel. If Red button has not
popped out, go to next step. If Red button has popped out, repair short circuit and press Red button to
reset circuit breaker.
2. Turn ignition on. Turn blower switch to 4th position (high). Check voltage at Blue wire terminal of 2-
wire blower motor connector on bottom of blower case. If no voltage is present, repair wiring between
circuit breaker and blower motor.
3. If battery voltage is present, turn off blower switch and A/C switch (if equipped). Check voltage at
Blue/Red wire terminal of blower resistor 1-wire connector. If no voltage is present, replace blower
motor. If battery voltage is present, check voltage at Blue/White wire terminal of blower resistor
connector.
4. If no volta
ge is present, replace blower resistor. If battery voltage is present, check voltage at Blue/Red WARNING:To avoid injury from accidental air bag deployment, read and carefully
follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR
BAG SYSTEM procedures in AIR BAG article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
NOTE: Blower resistor uses a 1-wire connector and a 4-wire connector. The wire
in the 1-wire connector is Blue/Red, and one of the wires in the 4-wire
connector is Blue/Red. Check voltage at appropriate wire.

1991 Mazda MX-5 Miata
HEATER SYSTEM 1990-92 Heater Systems
Microsoft
Sunday, July 05, 2009 2:12:14 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.

Blower motor relay supplies power to blower motor. Blower resistor determines blower speed. With blower
switch in highest position, blower motor is grounded through blower switch. With blower switch in all other
positions, blower motor is grounded through blower resistor and blower switch.
Circuit through compressor clutch is completed when A/C relay is energized and pressure switch is closed. A/C
relay is energized when Engine Control Unit (ECU) unit grounds the solenoid circuit of the relay. The ECU
energizes A/C relay if evaporator thermoswitch is closed and A/C and blower switches are on. The ECU also
controls A/C relay operation according to engine load.
ADJUSTMENTS
AIRFLOW MODE DOOR
Set airflow mode control lever to vent position. Disconnect control cable at airflow mode door lever. Extend
airflow mode door lever until it stops, and hold it there. See Fig. 1
. Attach control cable to door lever and clip.
Ensure control lever moves freely between defrost and vent positions.
AIR-MIX (TEMPERATURE BLEND) DOOR
Set temperature control lever to maximum hot position. Disconnect control cable at air-mix door lever. See Fig.
1 . Extend air-mix door lever until it stops, and hold it there. Attach control cable to door lever and clip. Ensure
control lever moves freely between hot and cold positions.
RECIRCULATED/FRESH AIR DOOR
Set recirculated/fresh air control lever to fresh position. Disconnect control cable at recirculated/fresh air door
lever. Retract recirculated/fresh air door lever until it stops, and hold it there. Attach control cable to door lever
and clip. Ensure control lever moves freely between recirculated air and fresh air positions.
TESTING
AIR BAG WARNING
BLOWER MOTOR CIRCUIT
1. Check 30-amp HEATER circuit breaker in passenger compartment fuse panel. If Red button has not
popped out, go to next step. If Red button has popped out, repair short circuit and press Red button to
reset circuit breaker.
2. Turn ignition on. Turn blower switch to 4th position (high). Check voltage at Blue wire terminal of 2-
wire blower motor connector on bottom of blower case. If no voltage is present, repair wiring between
circuit breaker and blower motor. WARNING:To avoid injury from accidental air bag deployment, read and carefully
follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR
BAG SYSTEM procedures in AIR BAG article in the
ACCESSORIES/SAFETY EQUIPMENT Section.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.