keyless MAZDA MODEL 2 2017 (in English) User Guide

3–16
Before Driving
Doors and Locks
NOTE
  (With double locking system)  The double locking system can
be activated/deactivated using the
request switch.
 Refer to Double Locking System on
page 3-13 .
  The setting can be changed so that
the doors and the liftgate/boot lid
are locked automatically without
pressing the request switch.
 Refer to Personalisation Features on
page 9-13 .
 (Auto-lock function)  A beep sound is heard when all
doors and the liftgate are closed
while the advanced key is being
carried. All doors and the liftgate/
boot lid are locked automatically
after about three seconds when
the advanced key is out of the
operational range. Also, the hazard
warning lights À ash once. (Even
if the driver is in the operational
range, all doors and the liftgate/boot
lid are locked automatically after
about 30 seconds.) If you are out
of the operational range before the
doors and the liftgate/boot lid are
completely closed or another key
is left in the vehicle, the auto-lock
function will not work. Always make
sure that all doors and the liftgate/
boot lid are closed and locked before
leaving the vehicle. The auto-lock
function does not close the power
windows.
NOTE
  Auto re-lock function  After unlocking with the request
switch, all doors and the liftgate/boot
lid will automatically lock if any
of the following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights
will À ash for con¿ rmation.
 The time required for the doors to
lock automatically can be changed.
 Refer to Personalisation Features on
page 9-13 .
 


 Opening a door or the liftgate/boot
lid.
 


 Switching the ignition to any
position other than off.
Locking, Unlocking with
Transmitter
All doors and the liftgate/boot lid can be
locked/unlocked by operating the keyless
entry system transmitter, refer to Keyless
Entry System (page 3-3 ).

3–23
Before Driving
Doors and Locks
NOTE
(With the advanced keyless function) 

 A locked liftgate/boot lid can also
be opened while the key is being
carried.
  When opening the liftgate/boot lid
with the doors and the liftgate/boot
lid locked, it may require a few
seconds for the liftgate/boot lid latch
to release after the electric liftgate/
boot lid opener is pressed.
  The liftgate/boot lid can be closed
when the doors are locked with the
key left in the vehicle. However,
to prevent locking the key in the
vehicle, the liftgate/boot lid can
be opened by pressing the electric
liftgate/boot lid opener. If the liftgate/
boot lid cannot be opened despite
doing this procedure, ¿ rst push the
liftgate/boot lid completely closed,
then press the electric liftgate/boot
lid opener to fully open the liftgate/
boot lid .
 
 (Hatchback)  When the latch is released by
pressing the electric liftgate opener,
the liftgate raises slightly. If the
liftgate is not operated for a certain
period of time, the liftgate cannot be
raised.
 To open  Press the electric liftgate opener
again.
 To close  To close the liftgate from its slightly
raised position, open it ¿ rst by
pressing the electric liftgate opener,
then close it after waiting at least 1
second.
NOTE
  If the liftgate is not fully closed,
the driver is noti¿ ed by a warning
indicated in the instrument cluster.
 
 If the vehicle battery is dead or there
is a malfunction in the electrical
system and the liftgate/boot lid
cannot be unlocked, the liftgate/boot
lid can be opened by performing the
emergency procedure.
 Refer to When Liftgate/Boot Lid
Cannot be Opened on page 7-55 .
Closing the liftgate/boot lid
(Hatchback)
Lower the liftgate slowly using the liftgate
grip recess, then push the liftgate closed
using both hands.
Do not slam it. Pull up on the liftgate to
make sure it is secure.


Liftgate grip recess

(Saloon)
Use both hands to push the boot lid down
until the lock snaps shut. Do not slam it.
Pull up on the boot lid to make sure it is
secure.

3–45
Before Driving
Security System
Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights À ash for about
30 seconds when the system is triggered
by any one of the following:
 


 Unlocking a door with an inside door-
lock knob.
 


 Forcing open a door, the bonnet or the
liftgate/boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
 


 (With the intrusion sensor) 
 The intrusion sensor detects a movement
in the vehicle.

The system will be triggered again (up to
10 times) if one of the above conditions
remains.
 


 (With the intrusion sensor) 
 Disconnecting the battery terminal (the
hazard warning lights do not À ash).

The system will be triggered about 10
times.
NOTE
  The liftgate/boot lid does not open
while the theft-deterrent system is
operating.
  If the battery goes dead while the
theft-deterrent system is armed,
the siren/horn will activate and the
hazard warning lights will À ash when
the battery is charged or replaced.
How to Arm the System
1. Close the windows securely.
NOTE
(With the intrusion sensor)
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion Sensor
(With Intrusion Sensor) on page 3-46 .
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate/boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will À ash
once.
(With the advanced keyless function)
Press a request switch.

The security indicator light in the
instrument cluster À ashes twice per
second for 20 seconds.



5. After 20 seconds, the system is fully
armed.

3–47
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will À ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


 (With the advanced keyless function) 


 
 Pressing a request switch on the doors.

The hazard warning lights will À ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will À ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
 


 (With the advanced keyless function) 


 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate/boot lid
opener while the key is being carried.


The hazard warning lights will À ash twice.

4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-38 ).
NOTE

(SKYACTIV-G 1.3, SKYACTIV-G
1.5)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.

4–14
When Driving
Start/Stop Engine
Automatic transaxle
1. Engine idling stops when the brake pedal is depressed while the vehicle is driven (except
for driving in the R or M position second gear ¿ xed mode) and the vehicle is stopped.
2. The engine restarts automatically when the brake pedal is released with the selector lever
in the D or M position (not in second gear ¿ xed mode).
3. If the selector lever is in the N or P position, the engine does not restart when the brake
pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear ¿ xed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depressed when shifting the
selector lever while engine idling is stopped.)

Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
 


 (SKYACTIV-G 1.3, SKYACTIV-G 1.5) 
 The engine is warmed up.



 (SKYACTIV-D 1.5) 


 
 The engine is not cold.


 
 The fuel injection amount learning, which is performed periodically and automatically,
is not being performed.
 


 The engine has been started and the vehicle is driven for a certain period.



 The engine is started with the bonnet closed.



 The battery is in good condition.



 All doors, liftgate/boot lid, and bonnet are closed.



 The driver's seat belt is fastened.



 The air conditioner is not operating with the airÀ ow mode dial in the position.



 (Automatic air-conditioning) 


 
 The temperature setting dial for the air-conditioning is set to a position other than
maximum heating/maximum cooling (A/C ON).
 

 
 The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
 


 The i-stop warning light (amber) is not turned on/À ashing.



 The keyless entry & push button start system functions are normal.



 The brake vacuum is suf¿ ciently high.



 The steering wheel is not being operated.

7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


(Flashing)
Tyre Pressure
Monitoring System
Warning Light
* If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light À ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
WARNING
If the tyre pressure monitoring system warning light illuminates or À ashes, or the tyre
pressure warning beep sound is heard, decrease vehicle speed immediately and avoid
sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or À ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a À at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.

Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.


(Red)
(Turns on)
KEY Warning Light If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) À ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .


Security Indicator
Light If the engine does not start with the correct key, and the security indicator light remains
illuminated or À ashing, try the following:
Make sure the key is within the operational range for signal transmission. Switch the
ignition off, and then restart the engine. If the engine does not start after 3 or more tries,
contact an expert repairer, we recommend an Authorised Mazda Repairer.


(Amber)
High Beam Control
System (HBC)
Warning Light
* The light remains turned on if there is a problem with the system. Have your vehicle
inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
If the windscreen area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.

7–51
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
NOTE
  Placing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function
to operate depending on the weight
of the item.
  To allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger
seat. The sensor may not function
properly because the additional
seat cushion could cause sensor
interference.
  When a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Rear seat
*
The warning beep only sounds if a seat
belt is unfastened after being fastened.
Ignition Not Switched Off (STOP)
Warning Beep
If the driver's door is opened with the
ignition switched to ACC, a beep will
be heard continuously in the cabin to
notify the driver that the ignition has not
been switched OFF (STOP). Under this
condition, the keyless entry system will
not operate, the vehicle cannot be locked,
and the battery voltage will be depleted.
Key Removed from Vehicle
Warning Beep
Vehicles with advanced keyless function
If the key is taken out of the vehicle while
the ignition is not switched OFF and
all the doors are closed, the beep which
sounds outside of the vehicle will be heard
6 times, the beep which sounds inside
the vehicle will be heard 6 times, and the
KEY warning light (red) in the instrument
cluster À ashes continuously to notify
the driver that the ignition has not been
switched OFF.
Vehicles without advanced keyless
function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, a beep will be heard
in the cabin 6 times and the KEY warning
light (red) in the instrument cluster turns
on continuously to notify the driver that
the ignition has not been switched OFF.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key
is carried together with a metal object
or it is placed in a poor signal reception
area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with the
door open or ajar, or the ignition is not
switched OFF with a key being carried, a
beep will be heard outside for about
2 seconds to notify the driver that the door
or liftgate/boot lid cannot be locked.

7–52
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Key Left-in-luggage Compartment/
Boot Warning Beep (With the
advanced keyless function)
If the key is left in the luggage
compartment/boot with all the doors
locked and the liftgate/boot lid closed, a
beep will be heard outside for about
10 seconds to notify the driver that the
key is in the luggage compartment/boot.
In this case, take out the key by pressing
the electric liftgate/boot lid opener and
opening the liftgate/boot lid. The key
taken out of the luggage compartment/
boot may not operate because its functions
have been temporarily stopped. To restore
the key's functions, perform the applicable
procedure (page 3-8 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If all the doors and luggage compartment/
boot are locked using another key while
the key is left in the cabin, the beep
which sounds outside of the vehicle will
be heard for about 10 seconds to notify
the driver that the key is in the cabin. In
this case, take out the key by opening the
door. A key taken out of the vehicle using
this method may not operate because its
functions have been temporarily stopped.
To restore the key's functions, perform the
applicable procedure (page 3-8 ).
Electronic Steering Lock Warning
Beep
The warning beep operates if the steering
wheel is not unlocked after the push button
start is pressed. (page 4-4 )
i-stop Warning Beep *
















 If the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver that
engine idling is stopped. It stops when
the driver's door is closed.
 


 The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
 

 
 (European model) 
 The driver's seat belt is unfastened and
the driver's door is opened.
 

 
 (Except European model) 


 
 (Manual transaxle) 
 With the shift lever in a position
other than neutral, the driver's seat
belt is unfastened and the driver's
door is opened.
 

 
 (Automatic transaxle) 
 With the selector lever in the D or
M (not in second gear ¿ xed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.


Vehicle Speed Alarm *
The vehicle speed alarm function is
designed to alarm the driver via a single
beep sound and a warning indication in the
instrument cluster that the previously set
vehicle speed has been exceeded.
You can change the vehicle speed setting
at which the warning is triggered.
120 km/h Warning Beep *
If the vehicle speed exceeds 120 km/h, a
chime sounds for 5 seconds.

8–6
Customer Information
Declaration of Conformity
Declaration of Conformity
Keyless Entry System/Immobilizer System