roof MAZDA MODEL 2 2017 Owners Manual (in English)

2–24
Essential Safety Equipment
Child Restraint
WARNING
Do not install a front-facing child-restraint system on the front passenger seat unless it
is unavoidable:
In a collision, the force of a deploying air bag could cause serious injury or death to
the child. If installing a front-facing child-restraint system on the front passenger seat
is unavoidable, move the front passenger seat as far back as possible and adjust the
seat bottom (height adjustable seat bottom) to the highest position at which the seat belt
fastening the child-restraint system is securely tightened.
Make sure that the front passenger air bag deactivation switch is in the OFF position.
Refer to Front Passenger Air Bag Deactivation Switch (page 2-47 ).


Do not allow a child or anyone to lean over or against the side window of a vehicle with
side and curtain air bags:
It is dangerous to allow anyone to lean over or against the side window, the area of the
front passenger seat, the front and rear window pillars and the roof edge along both
sides from which the side and curtain air bags deploy, even if a child-restraint system
is used. The impact of inÀ ation from a side or curtain air bag could cause serious
injury or death to an out of position child. Furthermore, leaning over or against the
front door could block the side and curtain air bags and eliminate the advantages of
supplementary protection. With the front air bag and the additional side air bag that
comes out of the front seat, the rear seat is always a better location for children. Take
special care not to allow a child to lean over or against the side window, even if the
child is seated in a child-restraint system.

Never use one seat belt on more than one person at a time:
Using one seat belt for more than one person at a time is dangerous. A seat belt used
in this way cannot spread the impact forces properly and the two passengers could
be crushed together and seriously injured or even killed. Never use one belt for more
than one person at a time and always operate the vehicle with each occupant properly
restrained.

2–41
Essential Safety Equipment
SRS Air Bags
*Some models.
Supplementary Restraint System (SRS) Precautions
The front and side supplementary restraint systems (SRS) include different types of air bags.
Please verify the different types of air bags which are equipped on your vehicle by
locating the “SRS AIRBAG” location indicators. These indicators are visible in the area
where the air bags are installed.
The air bags are installed in the following locations:
 


 The steering wheel hub (driver air bag)



 The front passenger instrument panel (front passenger air bag)



 The outboard sides of the front seatbacks (side air bags) * 



 The front and rear window pillars, and the roof edge along both sides (curtain air bags) *

The air bag supplementary restraint systems are designed to provide supplementary
protection in certain situations so seat belts are always important in the following ways:

Without seat belt usage, the air bags cannot provide adequate protection during an accident.
Seat belt usage is necessary to:
 


 Keep the occupant from being thrown into an inÀ ating air bag.



 Reduce the possibility of injuries during an accident that is not designed for air bag
inÀ ation, such as roll-over or rear impact.




 Reduce the possibility of injuries in frontal, near frontal or side collisions that are not
severe enough to activate the air bags.
 


 Reduce the possibility of being thrown from your vehicle.



 Reduce the possibility of injuries to lower body and legs during an accident because the
air bags provide no protection to these parts of the body.
 


 Hold the driver in a position which allows better control of the vehicle.

A child who is too small to use a seat belt must be properly secured using a child-restraint
system (page 2-21 ).

Carefully consider which child-restraint system is necessary for your child and follow
the installation directions in this Owner's Manual as well as the child-restraint system
manufacturer's instructions.

2–43
Essential Safety Equipment
SRS Air Bags
WARNING
Sit in the centre of the seat and wear seat belts properly:
Sitting too close to the side air bag modules or placing hands on them, or sleeping up
against the door or hanging out the windows is extremely dangerous. The side and
curtain air bags inÀ ate with great force and speed directly expanding along the door on
the side the car is hit. Serious injury could occur if someone is sitting too close to the
door or leaning against a window, or if rear seat occupants grab the sides of the front
seatbacks. Give the side and curtain air bags room to work by sitting in the centre of the
seat while the vehicle is moving with seat belts worn properly.

Do not attach objects on or around the area where driver and front passenger air bags
deploy:
Attaching an object to the driver and front passenger air bag modules or placing
something in front of them is dangerous. In an accident, an object could interfere with
air bag inÀ ation and injure the occupants.

Do not attach objects on or around the area where a side air bag deploys:
Attaching objects to the front seat in such a way as to cover the outboard side of the seat
in any way is dangerous. In an accident the object could interfere with the side air bag,
which inÀ ates from the outboard side of the front seats, impeding the added protection
of the side air bag system or redirecting the air bag in a way that is dangerous.
Furthermore, the bag could be cut open releasing the gas.
Do not hang net bags, map pouches or backpacks with side straps on the front seats.
Never use seat covers on the front seats. Always keep the side air bag modules in your
front seats free to deploy in the event of a side collision.

Do not attach objects on or around the area where a curtain air bag deploys:
Attaching objects to the areas where the curtain air bag activates such as on the
windscreen glass, side door glass, front and rear window pillars and along the roof edge
and assist grips is dangerous. In an accident the object could interfere with the curtain
air bag, which inÀ ates from the front and rear window pillars and along the roof edge,
impeding the added protection of the curtain air bag system or redirecting the air bag in
a way that is dangerous. Furthermore, the bag could be cut open releasing the gas.
Do not place hangers or any other objects on the assist grips. When hanging clothes,
hang them on the coat hook directly. Always keep the curtain air bag modules free to
deploy in the event of a side collision.

Do not touch the components of the supplementary restraint system after the air bags
have inÀ ated:
Touching the components of the supplementary restraint system after the air bags have
inÀ ated is dangerous. Immediately after inÀ ation, they are very hot. You could get
burned.

2–45
Essential Safety Equipment
SRS Air Bags
WARNING
Do not operate a vehicle with damaged air bag/seat belt pretensioner system
components:
Expended or damaged air bag/seat belt pretensioner system components must be
replaced after any collision which caused them to deploy or damage them. Only a
trained expert repairer, we recommend an Authorised Mazda Repairer can fully
evaluate these systems to see that they will work in any subsequent accident. Driving
with an expended or damaged air bag or pretensioner unit will not afford you the
necessary protection in the event of any subsequent accident which could result in
serious injury or death.

Do not remove interior air bag parts:
Removing any components such as the front seats, front instrument panel, the steering
wheel or parts on the front and rear window pillars and along the roof edge, containing
air bag parts or sensors is dangerous. These parts contain essential air bag components.
The air bag could accidentally activate and cause serious injuries. Always have an
Authorised Mazda Repairer remove these parts.

Properly dispose of the air bag system:
Improper disposal of an air bag or a vehicle with live air bags in it can be extremely
dangerous. Unless all safety procedures are followed, injury could result. Have an
expert repairer, we recommend an Authorised Mazda Repairer safely dispose of the air
bag system or scrap an air bag equipped vehicle.

2–54
Essential Safety Equipment
SRS Air Bags
*Some models.
Side Air Bags *
The side air bags are mounted in the outboard sides of the front seatbacks.
When the air bag crash sensors detect a side impact of greater than moderate force, the
system inÀ ates the side air bag only on the side in which the vehicle was hit. The side
air bag inÀ ates quickly to reduce injury to the driver or front passenger's chest caused by
directly hitting interior parts such as a door or window.
For more details about air bag deployment, refer to "SRS Air Bag Deployment Criteria"
(page 2-56 ).



Curtain Air Bags *
The curtain air bags are mounted in the front and rear window pillars, and the roof edge
along both sides.
When the air bag crash sensors detect a side impact of greater than moderate force, the
curtain air bag inÀ ates quickly and helps to reduce injury mainly to the rear outboard
passenger's head caused by directly hitting interior parts such as a door or window.
For more details about air bag deployment, refer to "SRS Air Bag Deployment Criteria"
(page 2-56 ).


Only one side curtain air bag will deploy on the
side of the vehicle that receives the force of an
impact.

4–35
When Driving
Instrument Cluster and Display
*Some models.
Active Driving Display *

Optical receiver Mirror
Combiner

WARNING
Always adjust the display brightness and position with the vehicle stopped:
Adjusting the display brightness and position while driving the vehicle is dangerous as
doing so could distract your attention from the road ahead and lead to an accident.
CAUTION
  Do not try to adjust the angle or open/close the active driving display manually.
Fingerprints on the display will make it dif¿ cult to view and using excessive force
when operating it could cause damage.
  Do not place objects in the vicinity of the active driving display. The active driving
display may not operate or any interference with its operation could cause damage.
  Do not place beverages near the active driving display. If water or other liquids are
splashed on the active driving display, it could cause damage.
  Do not place objects above the active driving display or apply stickers to the dust-
proof sheet/optical receiver as they will cause interference.
  A sensor is integrated to control the display's luminosity. If the optical receiver is
covered, the display's luminosity will lower making the display dif¿ cult to view.

 Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.

4–158
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will not operate if the driver is
deliberately performing driving operations (accelerator pedal and steering wheel).
  The Smart City Brake Support (SCBS) system will operate under the following
conditions.
 


 The engine is running.



 The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



 The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



 The Smart City Brake Support (SCBS) system is not turned off.



 The DSC is not malfunctioning. 

 The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam reÀ ected off the reÀ ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 ReÀ ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signi¿ cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
pro¿ le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor.
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 When driving with tyres having signi¿ cantly different wear.

4–174
When Driving
i-ACTIVSENSE
NOTE
  In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
 


 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 Ice, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on
the windscreen.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
pro¿ le.




 When driving next to walls with no patterning (including fences and longitudinally
striped walls).
 


 The tail lights of the vehicle ahead are turned off.



 A vehicle is outside the illumination range of the headlights.



 The vehicle is making a sharp turn, or ascending or descending a steep slope.



 Entering or exiting a tunnel.



 Heavy luggage is loaded causing the vehicle to tilt.



 Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
 


 There are many light emitters on the vehicle ahead.



 When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off at nighttime.
 


 Elongated luggage or cargo is loaded onto installed roof rails and covers the Forward
Sensing Camera (FSC).
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 The vehicle is driven with tyres having signi¿ cantly different wear.



 The vehicle is driven on down slopes or bumpy roads.



 There are water puddles on the road.



 The surroundings are dark such as during the night, early evening, or early morning,
or in a tunnel or indoor parking lot.
 


 The illumination brightness of the headlights is reduced or the headlight illumination
is weakened due to dirt or a deviated optical axis.
 


 The target object enters the blind spot of the Forward Sensing Camera (FSC).



 A person or object bursts onto the road from the shoulder or cuts right in front of
you.
 


 You change lanes and approach a vehicle ahead.



 When driving extremely close to the target object.



 Tyre chains or a temporary spare tyre is installed.



 The vehicle ahead has a special shape. For example, a vehicle towing a trailer house
or a boat, or a vehicle carrier carrying a vehicle with its front pointed rearward.

4–195
When Driving
Rear View Monitor
*Some models.
Rear View Monitor *
The rear view monitor provides visual images of the rear of the vehicle when reversing.
WARNING
Always drive carefully con¿ rming the safety of the rear and the surrounding conditions
by looking directly with your eyes:
Reversing the vehicle by only looking at the screen is dangerous as it may cause an
accident or a collision with an object. The rear view monitor is only a visual assist
device when reversing the vehicle. The images on the screen may be different from the
actual conditions.
CAUTION
  Do not use the rear view monitor under the following conditions: Using the rear view
monitor under the following conditions is dangerous and could result in injury or
vehicle damage or both.
 


 Icy or snow-covered roads.



 Tyre chains or a temporary spare tyre is installed.



 The liftgate/boot lid is not fully closed.



 The vehicle is on a road incline. 

 When the display is cold, images may course across the monitor or the screen and
may be dimmer than usual, which could cause dif¿ culty in con¿ rming the surrounding
conditions of the vehicle. Always drive carefully con¿ rming the safety of the rear and
the surrounding conditions by looking directly with your eyes.
  Do not apply excessive force to the camera. The camera position and angle may
deviate.
  Do not disassemble, modify, or remove it as it may no longer be waterproof. 
 The camera cover is made of plastic. Do not apply degreasing agents, organic solvents,
wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe
off with a soft cloth immediately.
  Do not rub the camera cover forcefully with an abrasive or hard brush. The camera
cover or lens may be scratched which might affect the images.

6–63
Maintenance and Care
Owner Maintenance
*Some models.
Fuse Panel Description
Fuse block (Engine compartment)



DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 C/U IG1 15 A For protection of various circuits
2 ENGINE IG1 7.5 A Engine control system
3 SUNROOF 10 A —
4 INTERIOR 15 A Overhead light
5

7.5 A Engine control system
6 AUDIO2 15 A Audio system
7 METER1 10 A Instrument cluster
8 SRS1 7.5 A Air bag
9 METER2 7.5 A Instrument cluster
*
10 RADIO 7.5 A Audio system
11 ENGINE3 15 A Engine control system
12 ENGINE1 15 A Engine control system
13 ENGINE2 15 A Engine control system
14 AUDIO1 25 A Audio system
15 A/C MAG 7.5 A Air conditioner
*