instrument panel MAZDA MODEL 3 4-DOOR 2004 Owners Manual

3-25
Knowing Your Mazda
Security System
Form No. 8S18-EA-03I

Operation
Arming
The system is armed when the ignition
switch is turned from the ON to the ACC
position.
The security indicator light in the
instrument panel flashes every 2 seconds
until the system is disarmed.
Disarming
The system is disarmed when the ignition
switch is turned to the ON position with
the correct ignition key.
The security indicator light illuminates for
about 3 seconds and goes out.
If the engine doesn
’t start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
NOTE
• (U.S.A.)

This device complies with part 15
of the FCC Rules. Operation is
subject to the following two
conditions: (1) This device may not
cause harmful interference, and (2)
this device must accept any
interference received, including
interference that may cause
undesired operation.
• (CANADA)

This device complies with RSS-210
of Industry CANADA. Operation is
subject to the following two
conditions: (1) this device may not
cause interference, and (2) this
device must accept any interference,
including interference that may
cause undesired operation of the
device.
J48C_8S18-EA-03I_Edition3.book Page 25 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-13
Driving Your Mazda
Starting and Driving
Form No. 8S18-EA-03I

Manual Shift Mode
This mode gives you the feel of driving a
manual transaxle vehicle by operating the
shift lever and allows you to control
engine rpm and torque to the front wheels
much like a manual transaxle when more
control is desired.
To change to manual shift mode, shift the
lever from D to M.
To return to automatic shift mode, shift
the lever from M to D. IndicatorsShift position indicator
In manual shift mode, the "M" of the shift
position indicator in the instrument panel
illuminates.
Gear position indicator
The numeral for the selected gear
illuminates.
NOTE
•
If you change to manual shift mode
when the vehicle is stopped, the
gear will shift to M1.
• If you shift up once when the
vehicle is stopped and the gear is at
M1, the gear will shift to M2. M2 is
helpful for starting on slippery
surfaces.
NOTE
If the gears cannot be shifted down
when driving at higher speeds, the gear
position indicator will flash twice to
signal that the gears cannot be shifted
down.
Shift position
indicator
Gear position indicator
J48C_8S18-EA-03I_Edition3.book Page 13 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-22
Driving Your Mazda
Starting and Driving
Form No. 8S18-EA-03I
The tire pressure monitoring system
(TPMS) monitors the pressure for each
tire.
If tire pressure is too low or too high in
one or more tires, the system will inform
the driver via the warning light in the
instrument panel and by the warning beep
sound.
The tire pressure sensors installed on each
wheel send tire pressure data by radio
signal to the receiver unit in the vehicle.
TPMS does not alleviate your need to
check the pressure and condition of all
four tires before you drive each day.
Tire Pressure Monitoring
System*
Tire pressure sensors
•When the tire pressure monitoring
system warning light is lit, one or
more of your tires is significantly
under-inflated. You should stop and
check your tires as soon as possible,
and inflate them to the proper
pressure as indicated on the
vehicle
’s tire information placard.
Driving on a significantly under-
inflated tire causes the tire to
overheat and can lead to tire failure.
Under-inflation also reduces fuel
efficiency and tire tread life, and
may affect the vehicle ’s handling
and stopping ability. Each tire,
including the spare, should be
checked monthly when cold and set
to the recommended inflation
pressure as specified in the vehicle
placard and owner ’s manual.
• To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tire deflation or blow out.
NOTE
This device complies with part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
CAUTION
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 22 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI