oil change MAZDA MODEL 3 4-DOOR 2004 Owners Manual

6-16
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
•When driving over uneven surfaces, the
sound may jump.
• The CD player/changer has been
designed to play CDs bearing the
identification logo as shown. No other
discs can be played.
• Be sure never to touch the signal
surface when handling the CDs. Pick
up a CD by grasping the outer edge or
the edge of the hole and the outer edge.
• Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label). •
Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should
become soiled, gently wipe it with a
soft cloth from the center of the CD to
the edge.
• Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
• CDs, like traditional audio records, are
made of plastic. To avoid warping,
keep the CDs in their cases and do not
store them where they will be exposed
to direct sunlight.
• The CD player/changer ejects the CD if
the CD is inserted upside down. Also
dirty and/or defective CDs may be
ejected.
• 8 cm (3 in) CDs and CD accessories
(e.g. 8 cm disc adapter) cannot be used
in the CD player/changer.
• Do not insert cleaning discs in the CD
player/changer.
• Do not insert any disc with a peel-off
or seal on it.
J48C_8S18-EA-03I_Edition3.book Page 16 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-8
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I
I: Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R : Replace
C : Clean
*1:Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often than recommended intervals.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*3:If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air filter more often than the recommended intervals.
*4:If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, change the brake fluid annually.
Maintenance
Interval
(Number of months or
kilometers
(miles), whichever comes first)Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
×1000 miles6.25 12.518.752531.2537.543.755056.2562.568.757581.2587.593.75100
Engine valve clearance Audible inspect every 120,000km (75,000miles), if noisy, adjust
Drive belts
*1IIIIIIIIIIIIIIII
Engine oil*2RRRRRRRRRRRRRRRR
Engine oil filter*2RRRRRRRRRRRRRRRR
Cooling system IIIIIIII
Engine coolant Replace every 2 years
Air filter
*3CCRCCRCC
Spark plugs Replace every 120,000km (75,000miles)
Fuel filter RRRR
Fuel lines and hoses IIIIIIII
Evaporative system
(if installed) IIIIIIII
Battery electrolyte level and
specific gravity IIIIIIII
Brake lines, hoses and
connections IIIIIIII
Brake fluid
*4IIIRIIIRIIIRIIIR
Parking brake IIIIIIIIIIIIIIII
Power brake unit
(Brake booster) and hoses IIIIIIII
Disc brakes IIIIIIIIIIIIIIII
J48C_8S18-EA-03I_Edition3.book Page 8 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-11
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Improper or incomplete service may result in problems. This section gives instructions
only for items that are easy to perform.
As explained in the Introduction (page 8-2), several procedures can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you’re unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
Owner Maintenance Precautions
Maintenance Procedures:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedures. If you lack
sufficient knowledge and experience or the proper tools and equipment to do the
work, have it done by a qualified technician.
Running the Engine:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Therefore, if you must run the engine while working under the hood, make certain
that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and
all neckties, scarves, and similar loose clothing before getting near the engine or
cooling fan which may turn on unexpectedly.
Electrical Fan and Engine Inspection:
Inspecting the engine with the ignition switch in the ON position is dangerous. The
cooling fan could come on unexpectedly even when the engine isn’ t running. You
could be seriously injured by the fan. Turn the ignition switch off and remove the key
from the ignition switch when you inspect the engine.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 11 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-14
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly
—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Changing engine oil
1. Warm up the engine for a few minutes and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil into a suitable container.
3. Replace the drain plug washer after the oil has thoroughly drained.
4. Reinstall the plug tightly.
5. Fill the engine with new oil to the MAX mark on the dipstick.
6. Securely reinstall the oil-filler cap.
7. Start the engine and inspect around the drain plug for leaks.
8. Turn it off and wait 5 minutes for the oil to return to the oil pan.
Check the oil level and fill to the MAX
mark if necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Remove any oil splatter from the
exhaust manifold, the exhaust pipe and
the shield. Oil left on these areas will
smoke when the engine is running.
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don ’t check or
change the engine oil when the
engine is hot.
WARNING
CAUTION
WARNING
Front Loosen
Drain plugTighten
J48C_8S18-EA-03I_Edition3.book Page 14 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-19
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Inspecting Power Steering Fluid
Level
Inspect the fluid level in the reservoir at
each engine oil change with the engine off
and cold. Add fluid if necessary; it does
not require periodic changing.
The level must be kept between MIN and
MAX.
Visually examine the lines and hoses for
leaks and damage.
If new fluid is required frequently, consult
an Authorized Mazda Dealer.
•
Brake and clutch fluid will damage
painted surfaces. If brake or clutch
fluid does get on a painted surface,
wipe it off immediately.
• Using nonspecified brake and clutch
fluids (page 10-4) will damage the
systems. Mixing different fluids
will also damage them.
If the brake/clutch system
frequently requires new fluid,
consult an Authorized Mazda
Dealer.
CAUTIONPower Steering Fluid
To avoid damage to the power steering
pump, don
’t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 19 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-22
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
To inspect the washer fluid level in the
front reservoir, pull off the cap. Then,
holding your thumb over the hole in the
center of the cap, lift it straight up. The
fluid level can be seen from the fluid
column in the pipe. Add fluid if necessary.
Use plain water if washer fluid is
unavailable. But use only washer fluid in
cold weather to prevent it from freezing.All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood
’s secondary latch
keeps the hood from opening when the
primary latch is released.
NOTE
Front and rear washer fluid is supplied
from the same reservoir.
Body Lubrication
J48C_8S18-EA-03I_Edition3.book Page 22 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

11-6
Index
Form No. 8S18-EA-03I
T
Tire Pressure Monitoring System .... 5-22
System error activation
............. 5-24
Tire pressure monitoring system
warning light
............................. 5-23
Tires and wheels
....................... 5-24
Tires Flat Tire
...................................... 7-3
Inflation pressure
...................... 8-31
Replacement
............................. 8-33
Rotation
.................................... 8-32
Snow tires
................................. 4-10
Spare tire and tool storage
.......... 7-3
Specifications
........................... 10-8
Tire chains
................................ 4-11
Uniform tire quality grading system
(UTQGS)
.................................. 9-16
Tool
.................................................... 7-3
Towing Description
............................... 7-20
Emergency towing
.................... 7-20
Recreational towing
.................. 7-23
Towing caravan and trailers
(Europe)
.................................... 4-13
Trailer towing
........................... 4-13
Trailer Towing
................................. 4-13
Trip Meter
........................................ 5-27
Trunk Lid
......................................... 3-13
Trunk Light
...................................... 3-15
Turn and Lane-Change Signals
....... 5-47
V
Vanity Mirrors ................................. 6-35
Vehicle Information Labels
............. 10-2
W
Warning Lights ................................ 5-31
ABS
........................................... 5-35
Air bag system
.......................... 5-36
Automatic transaxle
.................. 5-38
Brake system
............................. 5-33
Charging system
....................... 5-34
Check engine
............................. 5-35
Door-ajar
................................... 5-38
Engine oil pressure
.................... 5-34
Front seat belt pretensioner
system
....................................... 5-36
Low fuel
.................................... 5-36
Low washer fluid level
............. 5-38
seat belt
..................................... 5-37
Tire pressure monitoring
system
....................................... 5-38
Warranty
............................................. 9-9
Washer Fluid
.................................... 8-21
Weights
............................................ 10-6
Wheel Replacement
......................... 8-34
Windows Power windows
......................... 3-16
Windshield Washer
.......................... 5-51
Windshield Wipers
........................... 5-49
Blades replacement
................... 8-24
Winter Driving
................................... 4-9
J48C_8S18-EA-03I_Edition3.book Page 6 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI