jump start MAZDA MODEL 3 4-DOOR 2013 Owners Manual

Black plate (171,1)
If the ABS warning light stays on while
you're driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function normally
as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
NOTE
lWhen the engine is jump-started to charge
the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs,
it is the result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
l(With DSC vehicles)
The brake assist system does not operate
while the ABS warning light is illuminated.
qElectronic Brake Force
Distribution System Warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may illuminate the brake
system warning light and the ABS
warning light on simultaneously. The
problem is likely to be the electronic
brake force distribution system.
WARNING
Do not drive with both the ABS warning
light and brake warning light
illuminated. Have the vehicle towed to
an Authorized Mazda Dealer to have
the brakes inspected as soon as
possible:
Driving when the brake system
warning light and ABS warning light
are illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly
in an emergency stop than under
normal circumstances.
qBrake Assist
During emergency braking situations
when it is necessary to depress the brake
pedal with greater force, the brake assist
system provides braking assistance, thus
enhancing braking performance.
When the brake pedal is depressed hard or
depressed more quickly, the brakes apply
more firmly.
Driving Your Mazda
Starting and Driving
5-9
Mazda3_8CV6-EA-12H_Edition3 Page171
Thursday, February 28 2013 11:27 AM
Form No.8CV6-EA-12H

Black plate (212,1)
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:Driving with the brake system
warning light illuminated is
dangerous. It indicates that your
brakes may not work at all or that
they could completely fail at any
time. If this light remains
illuminated, after checking that the
parking brake is fully released, have
the brakes inspected immediately.
qMalfunction Warning Light
When the ignition is switched ON, the
malfunction warning light illuminates and
then turns off after a few seconds.
The light illuminates continuously if any
one of the following occurs. Consult an
Authorized Mazda Dealer:
lThe brake switch has a malfunction.l(SKYACTIV-G 2.0)
There is a problem with the battery
system.
WARNING
Do not drive the vehicle with the
malfunction warning light illuminated.
Driving with the malfunction
warning light illuminated is
dangerous because the brake lights
and engine control system may not
operate normally due to a brake
switch malfunction which could lead
to an accident. Have your vehicle
inspected by an Authorized Mazda
Dealer.
qABS Warning Light
The warning light stays on for a few
seconds when the ignition is switched
ON.
If the ABS warning light stays on while
you're driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function normally
as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
NOTE
lWhen the engine is jump-started to charge
the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs,
it is the result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
l(With DSC vehicles)
The brake assist system does not operate
while the ABS warning light is illuminated.
5-50
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Mazda3_8CV6-EA-12H_Edition3 Page212
Thursday, February 28 2013 11:28 AM
Form No.8CV6-EA-12H

Black plate (437,1)
7In Case of an Emergency
Helpful information on what to do in an emergency.
Parking in an Emergency ............................................................. 7-2Parking in an Emergency .......................................................... 7-2
Flat Tire ......................................................................................... 7-3 Spare Tire and Tool Storage ...................................................... 7-3
Changing a Flat Tire ................................................................. 7-9
Overheating ................................................................................. 7-16 Overheating ............................................................................. 7-16
Emergency Starting .................................................................... 7-18 Starting a Flooded Engine ....................................................... 7-18
Jump-Starting .......................................................................... 7-19
Push-Starting ........................................................................... 7-24
Emergency Towing ..................................................................... 7-25 Towing Description ................................................................. 7-25
Tiedown Hook ........................................................................ 7-26
Recreational Towing ............................................................... 7-28
7-1
Mazda3_8CV6-EA-12H_Edition3 Page437
Thursday, February 28 2013 11:30 AM
Form No.8CV6-EA-12H

Black plate (455,1)
Jump-Starting
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you
feel unsure about jump-starting, we strongly recommend that you have a competent service
technician do the work.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.
Always wear eye protection when working near the battery:
Working without eye protection is dangerous. Battery fluid contains SULFURIC ACID
which could cause blindness if splashed into your eyes. Also, hydrogen gas produced
during normal battery operation, could ignite and cause the battery to explode.
Wear eye protection and protective gloves to prevent contact with battery
fluid: Spilled battery fluid is dangerous.
Battery fluid contains SULFURIC ACID which could cause serious injuries if it gets in
eyes, skin or clothing. If this happens, immediately flush your eyes with water for 15
minutes or wash your skin thoroughly and get medical attention.
Always keep batteries out of the reach of children:
Allowing children to play near batteries is dangerous. Battery fluid could cause
serious injuries if it gets in the eyes or on the skin.
Do not allow the positive () terminal to contact any other metal object that
could cause sparks: Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. When working near a
battery, do not allow metal tools to contact the positive (
) or negative ()
terminal of the battery.
In Case of an Emergency
Emergency Starting
7-19
Mazda3_8CV6-EA-12H_Edition3 Page455
Thursday, February 28 2013 11:30 AM
Form No.8CV6-EA-12H

Black plate (456,1)
Keep all flames, including cigarettes, and sparks away from open battery cells:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries.
Do not jump-start a frozen battery or one with a low fluid level: Jump-starting a frozen battery or one with a low fluid level is dangerous. It may
rupture or explode, causing serious injury.
Connect the negative cable to a good ground point away from the battery: Connecting the end of the second jumper cable to the negative (
) terminal of the
discharged battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Route the jumper cables away from parts that will be moving: Connecting a jumper cable near or to moving parts (cooling fans, belts) is dangerous.
The cable could get caught when the engine starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
SKYACTIV-G 2.0
Connect cables in numerical order and disconnect in reverse order.
Booster battery
Discharged battery
Jumper cables
7-20
In Case of an Emergency
Emergency Starting
Mazda3_8CV6-EA-12H_Edition3 Page456
Thursday, February 28 2013 11:30 AM
Form No.8CV6-EA-12H

Black plate (457,1)
MZR 2.0, MZR 2.3 DISI Turbo and MZR 2.5
Connect cables in numerical order and disconnect in reverse order.
Booster battery
Discharged battery
Jumper cables
In Case of an Emergency
Emergency Starting
7-21
Mazda3_8CV6-EA-12H_Edition3 Page457
Thursday, February 28 2013 11:30 AM
Form No.8CV6-EA-12H

Black plate (459,1)
4. Connect the jumper cables in the exactsequence as in the illustration.
lConnect one end of a cable to the
positive terminal on the discharged
battery (1).
lAttach the other end to the positive
terminal on the booster battery (2).
lConnect one end of the other cable
to the negative terminal of the
booster battery (3).
lConnect the other end to the ground
point indicated in the illustration
away from the discharged battery
(4).
5. Start the engine of the booster vehicle and run it a few minutes. Then start the
engine of the other vehicle.
6. When finished, carefully disconnect the cables in the reverse order described in
the illustration.
7. Install the battery cover.
CAUTION
Ø Do not use a tool which applies
excessive force such as a
screwdriver or pliers.
If excessive force is applied to the
clips, they could be damaged.
To prevent damaging the battery
cover, install the battery cover
using the following procedure. 1 Being careful not to contact the
cowl grille, insert the tabs on the
one end of the battery cover into
the holes of the battery tray and
engage the tabs.
Cowl grille Tab
Hole
SKYACTIV-G 2.0
Cowl grille Tabs
Holes
MZR 2.0, MZR 2.3 DISI Turbo
and MZR 2.5
2 Attach the clips on both sides ofthe battery cover.
Clips
In Case of an Emergency
Emergency Starting
7-23
Mazda3_8CV6-EA-12H_Edition3 Page459
Thursday, February 28 2013 11:30 AM
Form No.8CV6-EA-12H

Black plate (606,1)
D
Dynamic Stability Control (DSC) ..... 5-28DSC OFF indicator light ............ 5-29
DSC OFF switch ........................ 5-29
TCS/DSC indicator light ............ 5-29
E
Emergency Starting ........................... 7-18Flooded engine ........................... 7-18
Jump-starting .............................. 7-19
Push-starting .............................. 7-24
Emergency Towing ........................... 7-25
Emission Control System .................... 4-4
Engine Coolant ....................................... 8-25
Exhaust gas .................................. 4-5
Hood release .............................. 3-50
Oil .............................................. 8-21
Overheating ................................ 7-16
Starting ......................................... 5-3
Engine Compartment Overview ........ 8-19
Engine Coolant Overheating ................................ 7-16
Event Data Recorder ......................... 9-20
Exhaust Gas ........................................ 4-5
Exterior Care ..................................... 8-67
F
Flasher Hazard warning .......................... 5-77
Headlights .................................. 5-64
Flat Tire ............................................... 7-3 Changing ...................................... 7-9
Spare tire and tool storage ............ 7-3
Fluids Classification .............................. 10-5
Owner maintenance ................... 8-16
F
Fog Lights ......................................... 5-70
Foot Brake .......................................... 5-5
Front Seats
(Electrically Operated Seats) ............... 2-4
Front Seats
(Manually Operated Seats) ................. 2-2
FuelFiller lid and cap ........................ 3-49
Gauge ......................................... 5-44
Requirements ............................... 4-2
Tank capacity ............................. 10-6
Fuses ................................................. 8-58 Panel description ........................ 8-61
Replacement ............................... 8-58
G
Gauges .............................................. 5-42
Glove Compartment ........................ 6-192
H
Hazard Warning Flasher .................... 5-77
Hazardous Driving .............................. 4-8
HeadlightsControl ....................................... 5-64
Flashing ...................................... 5-67
High-low beam .......................... 5-67
Leveling ..................................... 5-67
On reminder ............................... 5-67
Hood Release .................................... 3-50
Horn .................................................. 5-76
I
Ignition Keys ........................................... 3-25
Switch .......................................... 5-2
11-4
Index
Mazda3_8CV6-EA-12H_Edition3 Page606
Thursday, February 28 2013 11:31 AM
Form No.8CV6-EA-12H

Black plate (607,1)
I
Illuminated Entry System ............... 6-176
Immobilizer System
(with Advanced Key) ........................ 3-54
Immobilizer System
(without Advanced Key) ................... 3-58
Indicator Lights ................................. 5-47AFS OFF .................................... 5-60
BSM OFF ................................... 5-61
Cruise ......................................... 5-60
DSC OFF .................................... 5-60
Headlight high-beam .................. 5-59
KEY ............................................ 5-57
Low engine coolant
temperature ................................ 5-59
Power steering malfunction ........ 5-61
Security ...................................... 5-58
Shift position .............................. 5-59
TCS/DSC ................................... 5-59
Turn signal/hazard warning ........ 5-62
Information Display ........................ 6-178 Audio display ........................... 6-179
Climate control display ............ 6-179
Clock ........................................ 6-179
Information display functions ... 6-178
Outside temperature display ..... 6-179
Inside Trunk Release Lever ............... 3-44
Instrument Cluster ............................. 5-42
Interior Care ...................................... 8-71
Interior Lights ................................. 6-176
J
Jump-Starting .................................... 7-19
K
Keyless Entry System ....................... 3-26
Keys .................................................. 3-25
L
Label Information ............................. 10-2
Lane-Change Signals ........................ 5-69
Liftgate .............................................. 3-38 Luggage compartment ............... 3-41
Light Bulbs Replacement ............................... 8-46
Specifications ........................... 10-11
Lighting Control ............................... 5-64
Lubricant Quality .............................. 10-5
Luggage Compartment Light .......... 6-177
M
Maintenance Introduction .................................. 8-2
Owner maintenance
precautions ................................. 8-17
Owner maintenance schedule ..... 8-16
Scheduled ..................................... 8-4
Manual Transaxle Operation ............. 5-10 Recommendations for shifting .... 5-11
Map Lights ...................................... 6-177
Meters and Gauges ........................... 5-42
Mirror Defroster ................................ 5-76
Mirrors Outside mirrors .......................... 3-65
Rearview mirror ......................... 3-66
Money-Saving Suggestions ................ 4-7
Moonroof .......................................... 3-52
Index
11-5
Mazda3_8CV6-EA-12H_Edition3 Page607
Thursday, February 28 2013 11:31 AM
Form No.8CV6-EA-12H