engine MAZDA MODEL 3 HATCHBACK 2005 (in English) Manual PDF

Black plate (251,1)
CAUTION
lUse the cold scale only as a
reference.
lIf outside temperature is lower than
about 20°C (70°F), start the engine
and inspect the fluid level after the
engine reaches operating
temperature.
lIf the vehicle has been driven for an
extended period at high speeds or in
city traffic in hot weather, inspect the
level only after stopping the engine
and allowing the fluid to cool for 30
minutes.
Fully insert the dipstick. When adding
fluid, inspect with the dipstick to make
sure it doesn't pass full.
NOTE
Inspect the fluid on both sides of the
dipstick in a well lit area for an accurate
reading.
Washer Fluid
qInspecting Washer Fluid Level
WARNING
Substitute Washer Fluid:
Using radiator antifreeze as washer
fluid is dangerous. If sprayed on the
windshield, it will dirty the windshield,
affect your visibility, and could result
in an accident. Use only windshield
washer fluid or plain water in the
reservoir.
Using Washer Fluid Without Anti-
freeze Protection in Cold Weather:
Operating your vehicle in
temperatures below 4 degrees C (40
degrees F) using washer fluid without
anti-freeze protection is dangerous as
it could cause impaired windshield
vision and result in an accident. In
cold weather, always use washer fluid
with anti-freeze protection.
NOTE
State or local regulations may restrict
the use of volatile organic compounds
(VOCs), which are commonly used as
anti-freeze agents in washer fluid. A
washer fluid with limited VOC content
should be used only if it provides
adequate freeze resistance for all
regions and climates in which the
vehicle will be operated.
Maintenance and Care
Owner Maintenance
8-21
Mazda3_8T97-EC-04J_Edition1 Page251
Saturday, September 25 2004 2:16 PM
Form No.8T97-EC-04J

Black plate (252,1)
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
To inspect the washer fluid level in the
front reservoir, pull off the cap. Then,
holding your thumb over the hole in the
center of the cap, lift it straight up. The
fluid level can be seen from the fluid
column in the pipe. Add fluid if necessary.
Use plain water if washer fluid is
unavailable. But use only washer fluid in
cold weather to prevent it from freezing.
NOTE
Front and rear washer fluid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
8-22
Maintenance and Care
Owner Maintenance
Mazda3_8T97-EC-04J_Edition1 Page252
Saturday, September 25 2004 2:16 PM
Form No.8T97-EC-04J

Black plate (253,1)
Air Filter
CAUTION
Don't drive without an air filter. This
could result in excessive engine wear.
This air filter may be cleaned with
compressed air and reused, or replaced,
depending on its condition. Unless it is
very dirty, simply shake it to remove
foreign particles. Each time you inspect it,
wipe inside the air cleaner housing with a
damp cloth.
qReplacing the Air Filter
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than the recommended intervals.
CAUTION
Use a Mazda genuine air filter. Use of
other filters could damage the airflow
sensor.1. Make sure the ignition switch is turned
off.
2. Remove the battery cover and battery
duct.
Battery duct
Battery cover
3. Unfasten the clamps.
4. Lift off the air filter cover and remove
the filter.
Air filter cover
Air filter
Maintenance and Care
Owner Maintenance
8-23
Mazda3_8T97-EC-04J_Edition1 Page253
Saturday, September 25 2004 2:16 PM
Form No.8T97-EC-04J

Black plate (276,1)
3. Turn the knobs counterclockwise and
lower the fuse block.
4. Locate the position of the suspected
fuse by using the chart inside the fuse
block cover.
5. Pull the fuse straight out with the fuse
puller provided on the inside of the
engine compartment fuse block cover.
6. Inspect it and replace if it's blown.
NormalBlown
7. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
8-46
Maintenance and Care
Owner Maintenance
Mazda3_8T97-EC-04J_Edition1 Page276
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (278,1)
qFuse Panel Description
Fuse block (Engine compartment)
12 3 45 6
789 10
11 12
13 14
15 16
17 18
1920 2122 23
24 25 26
27 2829
3031 3233 3435 36
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
1 FAN 40A Cooling fan
2 P/ST 80A EHPAS
3 BTN 40AFor protection of various
circuits
4 HEAD 40A Headlights
5 PTC 80A―
6 GLOW 60A―
7 ABS 1 30A ABS
í
8 ABS 2 20A ABSí
9ENGINE30AFor protection of various
circuits
10―― ―
11IG KEY
130A Ignition switch
12 STARTER20A Starter clutch
13IG KEY
230A Ignition switch
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
14―― ―
15 HEATER40A Blower motor
16―― ―
17DEFOG 40A Rear window defroster
18―― ―
19ABS IG 10A ABSí
20FOG 15A Fog lightsí
21HORN 15A Horn
22―― ―
23 H/CLEAN20A―
24 F/PUMP15A Fuel pump
25P/ST IG 10A Power steering
26A/C
MAG10A Air conditioner
27ALT 10A―
28―― ―
8-48
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8T97-EC-04J_Edition1 Page278
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (281,1)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
59―― ―
60HEAD
LOW R15AHeadlight low beams (RH),
Headlight levelingí
61HEAD
LOW L15A Headlight low beams (LH)
62―― ―
63―― ―
64―― ―
65SAS 10A Supplemental restraint system
66METER 10AInstrument cluster,
Immobilizer system, Shift
lock system
67 IGNITION20A ABSí, EHPASí
68WIPER 20A Windshield wiper
69 ENGINE20AFor protection of various
circuits
70IG SIG 10A Auto wiperí
71SAS 2 7.5A Supplemental restraint system
72―― ―
73―― ―
74SEAT
WARM20A―
75D/
LOCK
125A Power door lock
76A/C 10AAir conditioner, Heater
control unit
77P/
WIND
L30A Power window (LH)í
78P/
WIND
R30A Power window (RH)í
79BACK 10A Reverse lights
80SUN
ROOF7.5A Moonroofí
81TAIL L 7.5ATaillights (LH), Parking lights
(LH)
82 ILLUMI7.5A Illumination
83―― ―
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
84―― ―
85―― ―
86―― ―
Maintenance and Care
Owner Maintenance
8-51íSome models. Mazda3_8T97-EC-04J_Edition1 Page281
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (298,1)
Outside the United States
Government regulations in the United States require that automobiles meet specific
emission regulations and safety standards. Therefore, vehicles built for use in the United
States may differ from those sold in other countries.
The differences may make it difficult or even impossible for your vehicle to receive
satisfactory servicing in other countries. We strongly recommend that you NOT take your
Mazda outside the United States. However, in the event that you are moving to Canada
permanently, Mazda vehicles built for use in the United States could be eligible for
exportation to Canada with specific vehicle modifications to comply with the Canadian
Motor Vehicle Safety requirements (CMVSS).
NOTE
The above is applicable for a permanent import/export situation and not related to
travelers on vacation.
You may have the following problems if you do take your vehicle outside of the United
States:
lRecommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will
affect vehicle performance and damage the emission controls and engine.
lProper repair facilities, tools, testing equipment, and replacement parts may not be
available.
Please refer to your Manufacturer's Warranty Booklet for more information.
9-10
Customer Information and Reporting Safety Defects
Warranty
Mazda3_8T97-EC-04J_Edition1 Page298
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (299,1)
Outside Canada
Government regulations in Canada require that automobiles meet specific emission
regulations and safety regulations. Therefore, vehicles built for use in Canada may differ
from those sold in other countries.
The differences may make it difficult or even impossible for your vehicle to receive
satisfactory servicing in other countries. We strongly recommend that you NOT take your
Mazda outside Canada. However, in the event that you are moving to the United States
permanently, Mazda vehicles built for use in Canada could be eligible for exportation to the
United States with specific vehicle modifications to comply with the United States Federal
Motor Vehicle Safety Standards (FMVSS).
NOTE
The above is applicable for a permanent import/export situation and not related to
travelers on vacation.
You may have the following problems if you do take your vehicle outside of Canada:
lRecommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will
affect vehicle performance and damage the emission controls and engine.
lProper repair facilities, tools, testing equipment, and replacement parts may not be
available.
Please refer to your Manufacturer's Warranty Booklet for more information.
Customer Information and Reporting Safety Defects
Warranty
9-11
Mazda3_8T97-EC-04J_Edition1 Page299
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (301,1)
Add-On Non-Genuine Parts and Accessories
Non-genuine parts and accessories for Mazda vehicles can be found in stores.
These may fit your vehicle, but they are not approved by Mazda for use with Mazda
vehicles. When you install non-genuine parts or accessories, they could affect your
vehicle's performance or safety system; the Mazda warranty doesn't cover this. Before you
install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
WARNING
Installation of Non-Genuine Parts or Accessories:
Installation of non-genuine parts or accessories is dangerous. Improperly designed
parts or accessories could seriously affect your vehicle's performance or safety system.
This could cause you to have an accident or increase your chances of injuries in an
accident. Always consult an Authorized Mazda Dealer before you install non-genuine
parts or accessories.
Add-On Electrical and Electronic Equipment:
Incorrectly choosing or installing improper add-on equipment or choosing an
improper installer is dangerous. Essential systems could be damaged, causing engine
stalling, air-bag (SRS) activation, ABS inactivation, or a fire in the vehicle.
Be very careful in choosing and installing add-on electrical equipment, such as mobile
telephones, two-way radios, stereo systems, and car alarm systems.
Mazda assumes no responsibility for death, injury, or expenses that may result from the
installation of add-on non-genuine parts or accessories.
Customer Information and Reporting Safety Defects
Warranty
9-13
Mazda3_8T97-EC-04J_Edition1 Page301
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J

Black plate (311,1)
qEngine Number
Forward
Identification Numbers
10-3
Mazda3_8T97-EC-04J_Edition1 Page311
Saturday, September 25 2004 2:17 PM
Form No.8T97-EC-04J