maintenance reset MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

3–39
Before Driving
Windows
Auto-opening/closing
To fully open the window automatically,
press the switch completely down, then
release. The window will fully open
automatically.
To fully close the window automatically,
pull the switch completely up, then
release. The window will fully close
automatically.
To stop the window partway, pull or press
the switch in the opposite direction and
then release it.
Power window system initialization
procedure
If the battery was disconnected during
vehicle maintenance, or for other reasons
(such as a switch continues to be operated
after the window is fully open/closed),
the window will not fully open and close
automatically.
The power window auto function will only
resume on a power window that has been
reset.
1. Switch the ignition ON.
2. Make sure that the power window lock
switch located on the driver's door is
not depressed.
3. Press the switch and fully open the
window.
4. Pull up the switch to fully close the
window and continue holding the
switch for about 2 seconds after the
window fully closed. Jam-safe window
If a person's hands, head or an object
blocks the window during the auto-closing
operation, the window will stop and open
halfway.
WARNING
Make sure nothing blocks the window
just before it reaches the fully closed
position or while holding up the power
window switch:
Blocking the power window just before
it reaches the fully closed position or
while holding up the power window
switch is dangerous.
In this case, the jam-safe function
cannot prevent the window from
closing all the way. If fi ngers are
caught, serious injuries could occur.
NOTE
  Depending on driving conditions, a
closing power window could stop
and start opening when the window
feels a shock that is similar to
something blocking it.
 In the event the jam-safe function
activates and the power window
cannot be closed automatically, pull
and hold the switch and the window
will close.
  The jam-safe window function does
not operate until the system has been
reset.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–46
When Driving
Instrument Cluster and Display
Wrench Indicator Light *
When the ignition is switched ON, the
warning light is illuminated and then turns
off after a few seconds.
When illuminated
The wrench indicator light is illuminated
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
When fl ashing (SKYACTIV-D 2.2)
The sedimentor separates water from the
fuel.
If water accumulates in this fi lter, the
warning light will fl ash. When it does,
consult an expert repairer, we recommend
an Authorised Mazda Repairer as soon as
possible.
Low Engine Coolant Temperature
Indicator Light (Blue)
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suffi ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Glow Indicator Light
(SKYACTIV-D 2.2)
This light may illuminate when the
ignition is switched ON.
It turns off when the glow plugs are warm.
If the ignition is left switched ON for a
long period of time without the engine
running after the glow plugs are warmed
up, the glow plugs may warm up again
which will illuminate the glow indicator
light.
.B[EB@&'&&"@&EJUJPOJOEC







6–5
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometres (miles), whichever comes fi rst.
Months 12 24 36 48 60 72 84 96 108
×1000 km 20 40 60 80 100 120 140 160 180
×1000 miles 12.5 25 37.5 50 62.5 75 87.5 100
112.5
Body condition (for rust, corrosion and
perforation) Inspect annually.
Cabin air fi lter (if installed) R R R R
Tyres (including spare tyre) (with infl ation
pressure adjustment)
*11*12 I I I I I I I I I
Flat tyre repair kit (if installed)
*13 Inspect annually.
Chart symbols:
I : Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R : Replace
C : Clean
T : Tighten
Remarks:
*1 In the countries below, inspect the spark plugs at every 10,000 km (6,250 miles) or 12 months before replacing
them at the said interval.
Albania, Bosnia and Herzegovina, Bulgaria, Croatia, Latvia, Macedonia, Moldova, Montenegro, Romania,
Serbia, Ukraine
*2 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air fi lter more often
than the recommended intervals.
*3 Implement the fuel injection amount correction.
*4 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 20,000
km (12,500 miles) or 12 months.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in cold temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*5 MZR 1.6, SKYACTIV-G 1.5, SKYACTIV-G 2.0 and SKYACTIV-D 2.2 vehicles can select fl exible setting only
some countries in Europe. Consult an Authorised Mazda Repairer for details. Flexible setting can be set if the
vehicle is operated mainly where none of the following conditions apply.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
Once the fl exible maintenance is selected, the vehicle calculates the remaining oil life based on engine operating
conditions and lets you know when an oil change is due by illuminating the wrench mark in the instrument
cluster.
Replace the engine oil and fi lter when message/wrench mark is ON. And they must be changed at least once a
year or within 20,000 km (12,500 miles) since last engine oil and fi lter change.
The system must be reset whenever replacing the engine oil regardless of the message/wrench mark display.
.B[EB@&'&&"@&EJUJPOJOEC







6–6
Maintenance and Care
Scheduled Maintenance
*6 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil fi lter at
every 10,000 km (6,250 miles) or shorter.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*7 For SKYACTIV-D 2.2, reset the engine oil data after replacing the engine oil.
*8 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*9 Inspect the battery electrolyte level, specifi c gravity and outer appearance.
*10 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, replace the brake fl uid annually.
*11 Tyre rotation is recommended every 10,000 km (6,250 miles).
*12 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*13 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
.B[EB@&'&&"@&EJUJPOJOEC







6–14
Maintenance and Care
Scheduled Maintenance
*4 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil fi lter
more often than the recommended intervals.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*5 For SKYACTIV-D 2.2, reset the engine oil data after replacing the engine oil.
*6 Use FL22 type coolant in vehicles with the inscription “FL22” on the radiator cap itself or the surrounding area.
Use FL22 when replacing the coolant.
*7 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air fi lter more often
than the recommended intervals.
*8 Inspect the battery electrolyte level, specifi c gravity and outer appearance. If the vehicle is operated in extremely
hot and cold areas, inspect the battery electrolyte level, specifi c gravity and appearance every 10,000 km (6,250
miles) or 6 months. The sealed battery only requires an outer appearance inspection.
*9 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is
operated in extremely humid climates, replace the brake fl uid annually.
*10 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*11 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–15
Maintenance and Care
Scheduled Maintenance
Maintenance Monitor *
Maintenance Monitor (Type A/Type B audio)
“Oil Change” with fl exible setting *1 is available. Consult an Authorised Mazda Repairer for
details*2 . Once the system turns on, the wrench indicator light in the instrument cluster will
be illuminated when remaining oil life becomes less than 500 km (300 mile), or remaining
days are less than 15 (Whichever comes fi rst).
Reset method
Press and hold the TRIP button with the ignition switched off, then switch it on. Keep
pressing the TRIP button for more than 5 seconds. The master warning light will fl ash for a
few seconds when the reset is completed.
*1 The engine oil fl exible maintenance setting is available (only some countries in Europe).
Based on the engine operating conditions, the onboard computer in your vehicle
calculates the remaining oil life.
*2 Once the engine oil fl exible maintenance setting is selected, the system must be reset
whenever replacing the engine oil regardless of the wrench indicator light display.
Maintenance Monitor (Type C/Type D audio)
1. Select the icon on the home screen to display the “Applications” screen.
2. Select the “Maintenance” to display the maintenance list screen.
3. Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:
Tab Item Explanation
Maintenance Setting Notifi cation can be switched on/off.
Time (months) Displays the time or distance until maintenance is due.
Select this item to set the maintenance period.
“Scheduled Due!” is displayed in red and the wrench indicator
light in the instrument cluster will be illuminated when the
remaining distance is less than 500 km or 250 mile, or the
remaining number of days is less than 15 (whichever comes
fi rst). Distance (mile or km)
Reset Resets the time and distance to the initial values.
Once the system turns on, it needs to be reset whenever
carrying out maintenance.
.B[EB@&'&&"@&EJUJPOJOEC







6–16
Maintenance and Care
Scheduled Maintenance
Tab Item Explanation
Tyre Rotation Setting Notifi cation can be switched on/off.
Distance (mile or km) Displays the distance until tyre rotation is due.
Select this item to set the tyre rotation distance.
“Tyre Rotation Due!” is displayed in red and the wrench
indicator light in the instrument cluster will be illuminated
when the remaining distance is less than 500 km or 250 mile.
Reset Resets the remaining distance to the initial value.
Once the system turns on, it needs to be reset whenever rotating
the tyres.
Oil Change Setting
*1 Notifi cation can be switched on/off.
Distance (mile or km) Displays the distance until the oil replacement is due.
Select this item to set the oil replacement distance.
“Oil Change Due!” is displayed in red and the wrench indicator
light in the instrument cluster will be illuminated when the
remaining distance is less than 500 km or 250 mile.
Reset Resets the remaining distance to the initial value.
Once the system turns on, it needs to be reset whenever
replacing the engine oil.
*1 The engine oil fl exible maintenance setting is available (only some countries in Europe).
Consult an Authorised Mazda Repairer for details.
Once the engine oil fl exible maintenance setting is selected, you will see the following
items in the display. The vehicle calculates the remaining oil life based on the engine
operating conditions and lets you know when an oil change is due by illuminating the
wrench indicator light in the instrument cluster.
Tab Item Explanation
Oil Change Oil life (%) Displays the engine oil life until the oil replacement is due.
“Oil Change Due!” is displayed in red and the wrench indicator
light in the instrument cluster will be illuminated when
remaining oil life distance is less than 500 km (300 mile), or
remaining days are less than 15 (whichever comes fi rst).
Reset Resets the remaining oil life to 100 %.
The system must be reset whenever replacing the engine oil.
.B[EB@&'&&"@&EJUJPOJOEC







6–27
Maintenance and Care
Owner Maintenance
NOTE
(MZR 1.6, SKYACTIV-G 1.5 and SKYACTIV-G 2.0)
 
 It is normal for all engines to consume engine oil under normal driving conditions.  Engine oil consumption may be as high as 0.8 L/1000 km (1 L/800 miles). This may
be as a result of evaporation, internal ventilation or burning of the lubricating oil in
the working engine. Oil consumption may be higher when the engine is new due to
the running-in process. Oil consumption is also dependant on engine speed and engine
load. Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 2.2)
 
 Whenever the engine oil is replaced, the vehicles engine control unit needs to be
reset as soon as possible. Otherwise the wrench indicator light or engine oil warning
light may turn on. To reset the engine control unit, consult an expert repairer, we
recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit
reset procedure on page 6-28 .
  Inspect the engine oil level periodically. When inspecting the engine oil, if the engine
oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should
be done by an expert repairer, we recommend an Authorised Mazda Repairer. When
replacing the engine oil, inspect the oil level using the oil dipstick and refi ll so that the
engine oil level is within the range between Full to Low as shown in the fi gure.

X Mark Full Low
.B[EB@&'&&"@&EJUJPOJOEC







6–28
Maintenance and Care
Owner Maintenance
Vehicle Engine Control Unit Reset Procedure
NOTE
This procedure is intended for vehicles with SKYACTIV-D 2.2 and vehicles with
SKYACTIV-G 1.5 or SKYACTIV-G 2.0 which the engine oil fl exible maintenance setting
is selected.
After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer
perform the initialization (engine oil data resetting) of the recorded value. If the value
recorded by the computer is not initialized, the wrench indicator light may not turn off or it
may turn on earlier than normal.
NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed, and press and hold the selector for
about 5 seconds until the master warning light
fl ashes. 
Selector
3. After the master warning light fl ashes for several seconds, the initialization is
completed.
.B[EB@&'&&"@&EJUJPOJOEC