shift MAZDA MODEL 6 2003 (in English) User Guide

5-12
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

To shift from P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Move the shift lever.

Manual Shift Mode
This mode gives you the feel of driving a
manual transaxle vehicle by tapping the
shift lever forward and back while in this
mode.
To change to manual shift mode, shift the
lever from D to M.To return to automatic shift mode, shift
the lever from M to D.

Indicators
Shift position indicator
In manual shift mode, the "M" of the shift
position indicator in the instrument panel
illuminates.
Gear position indicator
In manual shift mode, the numeral for the
selected gear illuminates below the shift
position indicator.
NOTE
•
When the ignition switch is in the
LOCK position, the transaxle
cannot be shifted from P.
•
To be sure the vehicle is in park,
the ignition key cannot be
removed unless the shift lever is in
P.
NOTE
•
If you change to manual shift mode
when the vehicle is stopped, the
gear will shift to M1.
•
If you tap the shift lever back when
the vehicle is stopped and the gear
is at M1, the gear will shift to M2.
M2 is helpful for starting on
slippery surfaces.
Shift position
indicator
Gear position
indicator
shuseizumi_J56J_8R29_EA_02I.book Page 12 Wednesday, October 16, 2002 9:51 AM

5-13
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Shifting
Shifting up
(M1→M2→M3→M4→M5*)
To shift up to a higher gear, tap the shift
lever back ( ) once.
*3.0-liter engine model
Shifting down
(M5*→M4→M3→M2→M1)
To shift down to a lower gear, tap the shift
lever forward ( ) once.
*3.0-liter engine model
NOTE
If the gears cannot be shifted down
when driving at higher speeds, the gear
position indicator will flash twice to
signal that the gears cannot be shifted
down (page 5-14).
NOTE
•
When driving slowly, the gears may
not shift up depending on vehicle
speed (page 5-14).
•
In manual shift mode, gears do not
shift up automatically. Don’t run the
engine with the tachometer needle
in the RED ZONE. If the
tachometer needle enters the RED
ZONE, you may feel engine-
braking because the fuel delivery
will be stopped to protect the
engine. However, this does not
indicate an abnormality.
•
Gears may not be shifted from M1
to M2 right after shifting the lever
from D to M. Wait a few seconds
and then shift up to M2.
•
When depressing the accelerator
fully, the transaxle will shift to a
lower gear, depending on vehicle
speed.
shuseizumi_J56J_8R29_EA_02I.book Page 13 Wednesday, October 16, 2002 9:51 AM

5-14
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Shifting Specification
2.3-liter engine model
Shifting up
If the vehicle speed is lower than the
speed specified for each gear, the gear
cannot be shifted up to a higher gear.
At kickdown, shifting up to each gear is
only possible at the following speeds or
higher:
Shifting down
If the vehicle speed is higher than the
speed specified for each gear, the gear
cannot be shifted down to a lower gear.
During deceleration, the gears shift down
automatically when speed is reduced to
the following:
If the vehicle is kicked down at the
following speeds or lower, the gears shift
down automatically:Sudden Engine-Braking:Shifting down while driving on wet,
snowy, or frozen roads, or while
driving at high speeds causes sudden
engine braking, which is dangerous.
The sudden change in tire speed
could cause the tires to skid. This
could lead to loss of vehicle control
and an accident. Do not use sudden
engine braking on slippery road
surfaces or at high speeds.
NOTE
•
When driving at high speeds, the
gear may not shift down depending
on vehicle speed (page 5-14).
•
During deceleration, the gear may
automatically shift down depending
on vehicle speed (page 5-14).
•
When depressing the accelerator
fully, the transaxle will shift to a
lower gear, depending on vehicle
speed.
WARNING
Gear Vehicle speed
M1
→M2You can shift up to M2
whether the vehicle is
stopped or moving.
M2
→M3 20 km/h (12 mph)
M3
→M4 35 km/h (22 mph)
Gear Vehicle speed
M2
→M3 61 km/h (37 mph)
M3
→M4 154 km/h (95 mph)
Gear Vehicle speed
M4
→M3 157 km/h (98 mph)
M3
→M2 111 km/h (64 mph)
M2
→M1 45 km/h (28 mph)
Gear Vehicle speed
M4
→M3 31 km/h (19 mph)
M3 or M2
→M1 8 km/h (5 mph)
Gear Vehicle speed
M4
→M3 149 km/h (92 mph)
M3
→M2 56 km/h (34 mph)
shuseizumi_J56J_8R29_EA_02I.book Page 14 Wednesday, October 16, 2002 9:51 AM

5-15
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I
3.0-liter engine model
Shifting up
If the vehicle speed is lower than the
speed specified for each gear, the gear
cannot be shifted up to a higher gear.
At kickdown, shifting up to each gear is
only possible at the following speeds or
higher:
Shifting down
If the vehicle speed is higher than the
speed specified for each gear, the gear
cannot be shifted down to a lower gear.During deceleration, the gears shift down
automatically when speed is reduced to
the following:
If the vehicle is kicked down at the
following speeds or lower, the gears shift
down automatically:

Recommendations for Shifting
Upshifting
2.3-liter engine
For normal acceleration and cruising, we
recommend these shift points.
3.0-liter engine
For normal acceleration and cruising, we
recommend these shift points.
Gear Vehicle speed
M1
→M2You can shift up to M2
whether the vehicle is
stopped or moving.
M2
→M3 10 km/h (6 mph)
M3
→M4Between 25 and 63
km/h (15 and 39 mph),
depending on how
much the accelerator
pedal is depressed.
M4
→M5Between 44 and 86
km/h (27 and 53 mph),
depending on how
much the accelerator
pedal is depressed.
Gear Vehicle speed
M2
→M3 45 km/h (27 mph)
M3
→M4 69 km/h (42 mph)
M4
→M5 177 km/h (109 mph)
Gear Vehicle speed
M5
→M4 194 km/h (120 mph)
M4
→M3 133 km/h (82 mph)
M3
→M2 87 km/h (53 mph)
M2
→M1 46 km/h (28 mph)
Gear Vehicle speed
M5
→M4Between 44 and 86
km/h (27 and 53 mph),
depending on how
much the accelerator
pedal is released.
M4
→M3Between 25 and 63
km/h (15 and 39 mph),
depending on how
much the accelerator
pedal is released.
M3 or M2
→M1 10 km/h (6 mph)
Gear Vehicle speed
M5
→M4 177 km/h (109 mph)
M5
→M3 69 km/h (42 mph)
M4
→M3 69 km/h (42 mph)
M4
→M2 45 km/h (27 mph)
M3
→M2 45 km/h (27 mph)
M1 to M2 24 km/h (15 mph)
M2 to M3 40 km/h (25 mph)
M3 to M4 65 km/h (40 mph)
M1 to M2 24 km/h (15 mph)
M2 to M3 40 km/h (25 mph)
M3 to M4 65 km/h (40 mph)
M4 to M5 73 km/h (45 mph)
shuseizumi_J56J_8R29_EA_02I.book Page 15 Wednesday, October 16, 2002 9:51 AM

5-16
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I
Downshifting
When you must slow down in heavy
traffic or on a steep upgrade
, downshift
before the engine starts to overwork. This
gives better acceleration when you need
more speed.
On a steep downgrade
, downshifting
helps maintain safe speed and prolongs
brake life.

Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release all brakes while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight
and grade steepness. Descend slowly,
using the brakes only occasionally to
prevent them from overheating.Power steering is only operable when the
engine is running. If the engine is off or if
the power steering system is inoperable,
you can still steer, but it requires more
physical effort.
If the steering feels rigid during normal
driving, consult an Authorized Mazda
Dealer.
Power Steering
Never hold the steering wheel to the
extreme left or right for more than 5
seconds with the engine running.
This could damage the power steering
system.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 16 Wednesday, October 16, 2002 9:51 AM

5-28
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I
Seat Belt Warning Light 5-32
Door-Ajar Warning Light 5-33
Low Washer Fluid Level Warning Light 5-33
Automatic Transaxle Warning Light 5-33
Security Indicator Light 5-33
Headlight High-Beam Indicator Light 5-34
Shift Position Indicator Light 5-34
TCS Indicator Light 5-35
TCS OFF Indicator Light 5-35
Cruise Main Indicator Light 5-36
Cruise Set Indicator Light 5-36
Light-On Indicator Light 5-36 Signal Warning/Indicator Lights Page
shuseizumi_J56J_8R29_EA_02I.book Page 28 Wednesday, October 16, 2002 9:51 AM

5-34
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I

Headlight High-Beam Indicator
Light
This light indicates one of two things:
•
The high-beam headlights are on.
•
The turn signal lever is in the flash-to-
pass position.

Shift Position Indicator Light
This indicates the selected shift position
when the ignition switch is in the ON
position.
In manual mode, the "M" of the shift
position indicator illuminates and the
numeral for the selected gear illuminates
in the gear position indicator.
Gear position indicator
shuseizumi_J56J_8R29_EA_02I.book Page 34 Wednesday, October 16, 2002 9:51 AM

6-25
Interior Comfort
Au d i o S y s t e m
Form No. 8R29-EA-02I
Audio sound adjustment
1. Press the audio control dial to select
bass, mid-range, treble, fade, balance
or automatic level controls. The
selected function will be indicated.
*1Depending on the model, this
function, may not be available.
*2Depending on the mode selected, the
indication changes.
2. Turn the audio control dial to adjust the
selected functions as follows:
Indication Turn Left Turn Right
Decrease
bassIncrease
bass
Decrease
mid-
rangeIncrease
mid-range
Decrease
trebleIncrease
treble
Shift the
sound
to the
frontShift the
sound
to the rear
Shift the
sound
to the leftShift the
sound
to the right
Select
modeSelect
mode
*
*
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade, balance and
automatic level control, press the audio
control dial for 2 seconds. The unit
will beep and "CLEAR" will be
displayed.
shuseizumi_J56J_8R29_EA_02I.book Page 25 Wednesday, October 16, 2002 9:51 AM

8-18
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I

Inspecting Automatic transaxle
Fluid Level
The automatic transaxle fluid level should
be inspected regularly. Measure it as
described below.
The volume of fluid changes with the
temperature. Fluid must be checked at idle
without driving at normal operating
temperature.
1. Park on a level surface and set the
parking brake firmly.
2. Idle the engine about two minutes.
Push down on the brake pedal.
3. Move the shift lever through all ranges
and set it at P.4. With the engine still idling, pull out the
dipstick, wipe it clean, and put it back.
5. Pull it out again.
The proper fluid level is marked on the
dipstick as follows.
Fluid hot scale A
When the vehicle has been driven and the
fluid is at normal operating temperature,
about 65°
C (150°
F), the level must be
between Full and Low.
Fluid cold scale B
When the engine has not been running
and the outside temperature is about 20°
C
(70°
F), the level must be between Full and
Low.
Automatic transaxle Fluid
(ATF)
•
Low fluid level causes transaxle
slippage. Overfilling can cause
foaming, loss of fluid, and transaxle
malfunction.
•
Use specified fluid (page 10-3). A
nonspecified fluid could result in
transaxle malfunction and failure.
CAUTION
Sudden Vehicle Movement:Shifting the shift lever without first
depressing the brake pedal is
dangerous. The vehicle could move
suddenly and cause an accident.
Make sure the brake pedal is applied
before shifting the shift lever.
WARNING
Full
A
LowFull
B
Low
Full
A
Low
Full
B
Low 2.3-liter engine
3.0-liter engine
shuseizumi_J56J_8R29_EA_02I.book Page 18 Wednesday, October 16, 2002 9:51 AM

11-2
Form No. 8R29-EA-02I
Index
A
Accessory Socket ............................. 6-54
Add-On Non-Genuine Parts and
Accessories
...................................... 9-11
Air Bag Systems
.............................. 2-33
Air Filter
.......................................... 8-20
Ambient Temperature Display
........ 6-48
Antenna
............................................ 6-16
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-40
Ashtray
............................................. 6-50
Audio
Audio control switch
................ 6-40
Audio System
................................... 6-16
Audio set
................................... 6-23
Operating tips for audio
system
....................................... 6-16
Safety certification
.................... 6-42
Automatic Transaxle
Driving tips
............................... 5-16
Fluid
.......................................... 8-18
Indicators
.................................. 5-12
Manual shift mode
.................... 5-12
Recommendations for
shifting
...................................... 5-15
Shifting
..................................... 5-13
Shifting specification
................ 5-14
Shift-lock system
...................... 5-12
Transaxle ranges
....................... 5-11
B
Battery
Emergency starting
................... 7-14
Maintenance
............................. 8-24
Specifications
........................... 10-3
B
Beeps
Ignition key reminder
................ 5-36
Lights-on reminder
................... 5-36
Before Starting the Engine
................. 4-5
After getting in
............................ 4-5
Before getting in
......................... 4-5
Body Lubrication
............................. 8-20
Bottle Holder
.................................... 6-51
Brake/Clutch
Fluid
.......................................... 8-15
Brakes
Anti-lock brake system (ABS)
.... 5-7
Foot brake
...................................5-4
Pad wear indicator
...................... 5-8
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In
............................................. 4-6
Bulb Replacement
............................ 8-29
C
Capacities ......................................... 10-4
Carbon Monoxide
.............................. 4-4
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-12
Center Box
....................................... 6-52
Center Console
................................. 6-53
Child Restraint
Child restraint precautions
........ 2-21
Installing child-restraint
systems
...................................... 2-24
LATCH child-restraint
systems
...................................... 2-29
Child Safety Locks for Rear Door
..... 3-9
Cigarette Lighter
.............................. 6-49
Climate Control System
..................... 6-2
Gas specifications
..................... 10-4
Clock
................................................ 6-47
shuseizumi_J56J_8R29_EA_02I.book Page 2 Wednesday, October 16, 2002 9:51 AM