oil temperature MAZDA MODEL 6 2017 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL 6, Model: MAZDA MODEL 6 2017Pages: 578, PDF Size: 54.72 MB
Page 120 of 578
3–46
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at more than
56 km/h (35 mph), and do not allow
anyone to stand behind a wheel when
pushing the vehicle:When the vehicle is stuck, spinning the
wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tire
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tire
chains, window scraper, flares, a small
shovel, jumper cables, and a small bag of
sand or salt.
Ask an Authorized Mazda Dealer to check
the following:
Have the proper ratio of antifreeze in the
radiator.
Refer to Engine Coolant on page
6-29.
Inspect the battery and its cables. Cold
reduces battery capacity.
Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-26).
Inspect the ignition system for damage
and loose connections.
Use washer fluid made with antifreeze—
but do not use engine coolant antifreeze
for washer fluid (page 6-31).
NOTE
Remove snow before driving. Snow left
on the windshield is dangerous as it
could obstruct vision.
Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windshield.
Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
Drive slowly. Braking performance
can be adversely affected if snow or
ice adheres to the brake components. If
this situation occurs, drive the vehicle
slowly, releasing the accelerator pedal
and lightly applying the brakes several
times until the brake performance
returns to normal.
Mazda6_8FH2-EA-16F_Edition2.indb 462016/07/07 13:44:31
Page 157 of 578
4–33
When Driving
Instrument Cluster and Display
*Some models.
Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a system
malfunction.
Signal WarningPage
Brake System Warning Light*1*27-22
ABS Warning Light*1
Electronic
Brake Force Distribution
System Warning 7-22,
ABS warning 7-25
Charging System Warning Light*17-22
Engine Oil Warning Light*17-22
(Red)
*High Engine Coolant Temperature Warning Indication/
Warning Light*17-22
Power Steering Malfunction Indication/Malfunction
Indicator Light*17-22
Master Warning Indication/Warning Light*17-25
Electric Parking Brake Warning Light 7-25
Check Engine Light*17-25
Automatic Transaxle Warning Indication/Warning Light*17-25
Air Bag/Front Seat Belt Pretensioner System Warning
Light*17-25
Tire Pressure Monitoring System Warning Light*1
Flashing
7-25,
Illuminate 7-29
(Amber)
*KEY Warning Indication 7-25
Mazda6_8FH2-EA-16F_Edition2.indb 332016/07/07 13:44:44
Page 162 of 578
4–38
When Driving
Instrument Cluster and Display
*Some models.
SignalIndicator Page
*Blind Spot Monitoring (BSM) OFF Indicator Light*14-99
(Green)*i-ELOOP Indication Light 4-82
(White)
*Cruise Main Indication4-156
(Green)
*Cruise Set Indication4-156
*1 The light turns on when the ignition is switched on for an operation che\
ck, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains tur\
ned on, have the vehicle inspected at an
Authorized Mazda Dealer.
Wrench Indicator Light*
When the ignition is switched ON, the
wrench indicator light turns on and then
turns off after a few seconds.
The wrench indicator light turns on under
the following conditions:
When the preset maintenance period has
arrived.
When its time to replace the engine oil.
Refer to Maintenance Monitor on page
6-18.
Low Engine Coolant Temperature
Indicator Light (Blue)*
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
Mazda6_8FH2-EA-16F_Edition2.indb 382016/07/07 13:44:50
Page 311 of 578
5–17
Interior Features
Audio System
CDs bearing the logo shown in the
illustration can be played. No other discs
can be played.
Use discs that have been legitimately
produced. If illegally-copied discs such
as pirated discs are used, the system may
not operate properly.
Be sure never to touch the signal surface
when handling the CDs. Pick up a CD
by grasping the outer edge or the edge of
the hole and the outer edge.
Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label). The disc may not
eject resulting in a malfunction.
Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should become
soiled, gently wipe it with a soft cloth
from the center of the CD to the edge.
Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
The CD player ejects the CD if the CD
is inserted upside down. Also dirty and/
or defective CDs may be ejected.
Do not insert cleaning discs in the CD
player.
Do not insert any disc with a peel-off
seal affixed to it.
This unit may not be able to play certain
CD-R/CD-RWs made using a computer
or music CD recorder due to disc
characteristics, scratches, smudges, dirt,
etc., or due to dust or condensation on
the lens inside the unit.
Storing CDs in the vehicle exposed to
direct sunlight or high temperature may
damage the CD-R/CD-RWs, and make
them unplayable.
CD-R/CD-RW exceeding 700 MB
cannot be played.
This unit may not be able to play certain
discs made using a computer due to the
application (writing software) setting
used. (For details, consult the store
where the application was purchased.)
It is possible that certain text data, such
as titles, recorded on a CD-R/CD-RW
may not be displayed when musical data
(CD-DA) is playing.
The period from when a CD-RW is
inserted to when it begins playing is
longer than a normal CD or CD-R.
Completely read the instruction manual
and cautions for CD-R/CD-RWs.
Do not use discs with cellophane tape
adhering, partially peeled off labels,
or adhesive material exuding from the
edges of the CD label. Also, do not use
discs with a commercially-available
CD-R label affixed. The disc may not
eject resulting in a malfunction.
Mazda6_8FH2-EA-16F_Edition2.indb 172016/07/07 13:45:31
Page 390 of 578
6–4
Maintenance and Care
Scheduled Maintenance
Scheduled Maintenance (U.S.A., Canada, and Puerto Rico)
Follow Schedule 1 if the vehicle is operated mainly where none of the fo\
llowing conditions
(severe driving conditions) apply.
Repeated short-distance driving Driving in dusty conditions Driving with extended use of brakes Driving in areas where salt or other corrosive materials are used Driving on rough or muddy roads Extended periods of idling or low-speed operation Driving for long periods in cold temperatures or extremely humid climate\
s Driving in extremely hot conditions Driving in mountainous conditions continually
If any do apply, follow Schedule 2. (Puerto Rico and Canada residents follow Schedule 2.)
Engine oil flexible maintenance is available for U.S.A. and Puerto Rico residents whose
vehicle is operated mainly where none of the following conditions apply.
Extended periods of idling or low-speed operation such as police car, taxi or driving
school car
Driving in dusty conditions
If any do apply, follow Schedule 2 with engine oil fixed maintenance.
The onboard computer in your vehicle calculates the remaining oil life b\
ased on engine
operating conditions when selecting flexible maintenance. Mazda Genuine 0W-20 Oil and
Castrol
® 0W-20 Oil are required to achieve optimum calculation performance.
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
Mazda6_8FH2-EA-16F_Edition2.indb 42016/07/07 13:46:06
Page 415 of 578
6–29
Maintenance and Care
Owner Maintenance
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5 minutes
for the oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
MAX
OK
MIN
5. Pull it out again and examine the level.
The level is normal if it is between the
MIN and MAX marks.
If it is near or below MIN, add enough
oil to bring the level to MAX.
CAUTION
Do not overfill the engine oil. This may
cause engine damage.
6. Make sure the O-ring on the dipstick is
positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.
Engine Coolant
Inspecting Coolant Level
WARNING
Do not use a match or live flame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before attempting
to work near the cooling fan: Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and
radiator are hot: When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Mazda6_8FH2-EA-16F_Edition2.indb 292016/07/07 13:46:10
Page 455 of 578
6–69
Maintenance and Care
Appearance Care
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than
mild detergent. Before using any
detergent, verify the ingredients.
Otherwise, the product could discolor
or stain the aluminum wheels.
NOTE
Do not use a wire brush or any abrasive
cleaner, polishing compound, or solvent
on aluminum wheels. They may damage
the coating.
Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be sure
to clean the wheels after driving on
dusty or salted roads to help prevent
corrosion.
Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
Plastic Part Maintenance
When cleaning the plastic lenses of the
lights, do not use gasoline, kerosene,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolor or damage the
surfaces resulting in a significant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
gasoline, oil, engine coolant, or battery
fluid, it could cause discoloration,
staining, or paint peeling. Wipe off any
such chemical agents or fluids using a
soft cloth immediately.
High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
Mazda6_8FH2-EA-16F_Edition2.indb 692016/07/07 13:46:23
Page 457 of 578
6–71
Maintenance and Care
Appearance Care
*Some models.
Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
Upholstery Maintenance
1. Clean the soiled area by lightly dabbing
it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
Leather Upholstery Maintenance*
1. Remove dust and sand using a vacuum
cleaner.
2. Wipe off the soiled area with a soft
cloth and a suitable, special cleaner or
a soft cloth soaked in a mild detergent
(about 5%) diluted with water.
3. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
4. Remove moisture with a dry, soft cloth
and allow the leather to further dry in
a well-ventilated, shaded area. If the
leather gets wet such as from rain,
remove the moisture and dry it as soon
as possible.
NOTE
Because genuine leather is a natural
material, its surface is not uniform and
it may have natural scars, scratches,
and wrinkles.
To maintain the quality for as long as
possible, periodical maintenance, about
twice a year, is recommended.
If the leather upholstery comes into
contact with any of the following, clean
it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
Sand or dirt Grease or oil, such as hand cream Alcohol, such as in cosmetic or hair
dressing items
If the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such as
hardening and shrinkage.
Exposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car under
direct sunlight for long periods, shade
the interior using sunshades.
Do not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality
and coloring. If the cabin temperature
becomes hot, the vinyl may deteriorate
and adhere to the genuine leather.
Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discoloration, stains,
cracks or peeling of the coating.
Mazda6_8FH2-EA-16F_Edition2.indb 712016/07/07 13:46:23
Page 572 of 578
10–4
Index
Ending Screen Display ........................4-85
Engine Coolant .......................................... 6-29
Engine compartment overview ..... 6-25
Exhaust gas .................................... 3-27
Hood release .................................. 6-23
Oil .................................................. 6-26
Starting ............................................ 4-5
Engine Coolant Temperature
Gauge .........................................4-16, 4-24
Essential Information ............................ 6-2
Event Data Recorder ........................... 8-21
Exterior Care ....................................... 6-64
Aluminum wheel maintenance ...... 6-69
Bright-metal maintenance ............. 6-68
Maintaining the finish ................... 6-66
Plastic part maintenance ................ 6-69
F
Flasher
Hazard warning ............................. 4-65
Headlights ..................................... 4-53
Flat Tire ................................................. 7-3
Mounting the spare tire ................. 7-10
Removing a flat tire ......................... 7-7
Floor Mat ............................................ 3-45
Fluid Brake/Clutch ................................. 6-31
Washer ........................................... 6-31
Fluids Classification ................................... 9-4
Fog Lights ........................................... 4-58
Foot Brake ........................................... 4-70
Forward Sensing Camera (FSC) ....... 4-146
Fuel Filler lid and cap ............................ 3-28
Gauge ................................... 4-16, 4-24
Requirements ................................. 3-25
Tank capacity .................................. 9-5
Fuel Consumption Display ................. 4-84Fuel Economy Monitor .......................
4-83
Control Status Display .................. 4-85
Control status display .................... 4-85
Ending Screen Display ..................4-85
Ending screen display ................... 4-85
Fuel Consumption Display ............ 4-84
Fuel consumption display ............. 4-84
Fuses ................................................... 6-57
Panel description ........................... 6-59
Replacement .................................. 6-57
G
Gauges ................................................. 4-12
Glove Compartment ............................ 5-92
H
Hazard Warning Flasher ......................4-65
Hazardous Driving .............................. 3-45
Head Restraint ..................................... 2-13
Headlights Coming home light ........................ 4-57
Control ........................................... 4-53
Flashing ......................................... 4-56
Headlight flashing ......................... 4-56
High-low beam .............................. 4-56
Leaving home light ....................... 4-57
Leveling ......................................... 4-58
High Beam Control System (HBC) .... 4-91
High Beam Control System (HBC)
indicator light (green) .................... 4-93
Hill Launch Assist (HLA) ................... 4-74
HomeLink Wireless Control System ...4-66
Hood Release ...................................... 6-23
Horn .................................................... 4-65
Mazda6_8FH2-EA-16F_Edition2.indb 42016/07/07 13:46:50
Page 573 of 578
10–5
Index
I
i-ACTIVSENSE ..................................4-88
Active safety technology ............... 4-88
Adaptive Front Lighting System
(AFS) ............................................. 4-90
Blind Spot Monitoring (BSM) ...... 4-94
Camera and sensors ....................... 4-89
Distance Recognition Support System
(DRSS) ........................................ 4-107
Forward Sensing Camera (FSC) ...4-146
High Beam Control System
(HBC) ............................................ 4-91
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS) ....................................... 4-125
Mazda Radar Cruise Control
(MRCC) ....................................... 4-115
Pre-crash safety technology .......... 4-88
Radar sensor (front) .....................4-150
Radar sensors (rear) .....................4-153
Rear Cross Traffic Alert (RCTA) ...4-111
Smart Brake Support (SBS) ........ 4-143
Smart City Brake Support
(SCBS) ........................................ 4-138
Traffic Sign Recognition System
(TSR) ........................................... 4-100
i-ELOOP ............................................. 4-80
Control status display .................... 4-82
Display .......................................... 4-80
i-ELOOP Warning Beep ................ 7-38
i-ELOOP indicator light ................ 4-82
i-ELOOP warning beep ....................... 7-38
If a Warning Light Turns On or
Flashes................................................. 7-22
If the Active Driving Display does not
operate ................................................. 7-41
Ignition Switch .............................................. 4-4
Ignition Not Switched Off (STOP)
Warning Beep ...................................... 7-37
Illuminated Entry System ...................5-87
Immobilizer System ............................ 3-40Indication/Indicator Lights ..................
4-36
Indicator Lights Low engine coolant temperature ... 4-38
Wrench .......................................... 4-38
Inside Trunk Release Lever ................3-23
Inspecting Brake/Clutch Fluid Level ...6-31
Inspecting Coolant Level ....................6-29
Inspecting Engine Oil Level ............... 6-29
Inspecting Washer Fluid Level ............6-31
Instrument Cluster ............................... 4-12
Interior Care ........................................ 6-70
Active driving display
maintenance ................................... 6-72
Cleaning the floor mats ................. 6-73
Cleaning the window interiors ...... 6-72
Instrument panel top (Soft pad)
maintenance ................................... 6-72
Leather upholstery maintenance ... 6-71
Panel maintenance ......................... 6-72
Plastic part maintenance ................ 6-71
Seat belt maintenance .................... 6-70
Upholstery maintenance ................ 6-71
Vinyl upholstery maintenance .......6-71
Interior Lights ..................................... 5-85
Courtesy lights .............................. 5-85
Map lights ...................................... 5-85
Overhead lights ............................. 5-85
J
Jack ....................................................... 7-4
Jump-Starting ...................................... 7-13
Mazda6_8FH2-EA-16F_Edition2.indb 52016/07/07 13:46:50