ignition MAZDA MODEL 626 2001 Owner's Manual

Form No. 8P95-EA-00G
Driving Your Mazda5-2

042-1CE
Ignition Switch PositionsWithout immobilizer
system
J94A4001A
 ON
This is the normal running position
after the engine is started. The warning
lights (except brakes) should be
inspected before the engine is started
(page 5-35).
With immobilizer
system
J94S5001
 START
The engine is started in this position. It
will crank until you release the key;
then it returns to the ON position. The
brake warning light can be checked
after the engine is started (page 5-35). 
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
 LOCK
The steering wheel locks to protect
against theft. Only in this position can
the key be removed.

Form No. 8P95-EA-00G
Driving Your Mazda
5-3
042-2DE
LOCK(0)ON(II)
ACC(I)
Push the key
J94A4003 Manual transaxle
When turning the ignition switch to
the LOCK position, push the key in at
the ACC position.

042-3FE
J94S.J94A4004
LOCK(0) ON(II)
ACC(I)
Shift lever
engaged in P
(park)
 Automatic transaxle
When turning the ignition switch to
the LOCK position, keep the shift
lever at P.

042-4AE
NOTEIf turning the key is difficult, jiggle
the steering wheel from side to
side.

042-5BE
WARNING
!
Removing the Key:It’s dangerous to remove the key
from the ignition switch while the
vehicle is moving. Removing the
key allows the steering wheel to
lock. You will lose steering control
and a serious accident could
occur. Remove the key only when
the vehicle is parked.

Form No. 8P95-EA-00G
Driving Your Mazda5-4

Q042-6EE
WARNING
!
Not Setting the Parking Brake:Leaving the driver ’s seat without
setting the parking brake is
dangerous. Unexpected vehicle
movement could occur if the
parking brake is not set. This
could cause an accident. Before
leaving the driver ’s seat, always
set the parking brake and make
sure the shift lever is at P with an
automatic transaxle or in 1 or R
with a manual transaxle.
042-7A1E
NOTEIf the ignition switch is in the
LOCK or ACC position, a beep
will sound when any door is
opened.

Q043-8AE
Starting the Engine1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.

Form No. 8P95-EA-00G
Driving Your Mazda
5-5

043-9B1E
4. (Manual transaxle)
Depress the clutch pedal all the
way and shift into neutral.
Keep the pedal depressed while
cranking the engine.
(Automatic transaxle)
Place the shift lever in P. If you
must restart the engine while the
vehicle is moving, shift the lever to
N.

043-10BE
NOTEThe starter will not operate...
• If the shift lever is not in P or N
(automatic), or
• If the clutch pedal is not
pushed down all the way
(manual).

043-4HE
5. Turn the ignition switch to the
START position and hold (up to 10
seconds at a time) until the engine
starts.

043-5AE
CAUTION
!
Don’t try the starter for more than
10 seconds at a time. If the engine
stalls or fails to start, wait 10
seconds before trying again.
Otherwise, you may damage the
starter and drain the battery.

Form No. 8P95-EA-00G
Driving Your Mazda5-66. After starting the engine, let it idlefor about 10 seconds.NOTEIn extremely cold weather, below
–18 °C (0° F), or after the vehicle
has stood idle several days, let the
engine warm up without operating
the accelerator.
043-2EE
NOTEWhether cold or warm, the engine
should be started without use of
the accelerator.If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and hold it there. 2. Turn the ignition switch to the
START position and hold it
there—for up to 10 seconds. If the
engine starts, release the key and
accelerator immediately because
the engine will suddenly rev up.
3. If the engine fails to start, crank it without using the accelerator—for
up to 10 seconds.

Form No. 8P95-EA-00G
Driving Your Mazda
5-9
045-1AE
Automatic TransaxleAutomatic Transaxle Controls
Various Lockouts:
Indicates that you must depress the brake pedal
and, hold in the lock-release button to shift
(The ignition switch must be in the ACC or ON position.)The shift lever can be shifted freely into any position
indicated by the arrow. Lock-release button
To prevent unsafe shifting
Shift pattern indicator
Shows shift lever position
Shift lever
Overdrive button
For selecting either a three-speed or four-speed transaxle
Overdrive (O/D) OFF
indicator
This indicator comes on
when the overdrive has
been turned off.
J94A4007
J94A4006_a
Indicates that you must hold in the lock-release button to shift.
J94S.J94A4006_a+7

Form No. 8P95-EA-00G
Driving Your Mazda
5-15

045-11JE
 Shift-Lock System
For your safety, the automatic
transaxle has a shift-lock, which
prevents shifting out of P unless the
brake pedal is depressed.
To shift from P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Push and hold the lock-release button.
4. Move the shift lever.
NOTE• When the ignition switch is in
the LOCK position, the
transaxle cannot be shifted
from P.
• To be sure the vehicle is in
park, the ignition key cannot
be removed unless the shift is
in P.

Form No. 8P95-EA-00G
Driving Your Mazda
5-17

114 –2B1E
J94A4010
Traction Control Indicators
 Traction control system (TCS)
warning light
This warning light stays on for a few
seconds when the ignition switch is
turned to the ON position. It flashes when the system regulates
engine torque. If the light stays on,
take your vehicle to an Authorized
Mazda Dealer. The traction control
system may have a malfunction.
NOTE•
In addition to the TCS warning
light flashing, a slight lugging
sound will come from the
engine. This indicates that the
traction control system is
operating properly.
• On slippery surfaces, such as
fresh snow, it will be
impossible to achieve high rpm
when the traction control
system is on.

Form No. 8P95-EA-00G
Driving Your Mazda5-18
J94A4011
TCS OFF Indicator Light
This light comes on when the ignition
switch is turned to the ON position. It
goes off when the engine is started. It also comes on when you switch off
the traction control system or when the
system has a malfunction.
NOTEAfter starting the engine on very
cold days, the TCS OFF indicator
will remain on and the system will
not operate until the engine is
warm.


114-3AE
J94A4012 TCS OFF Switch
Push this switch once to turn off the
TCS. Push it again to turn the TCS
back on.

Form No. 8P95-EA-00G
Driving Your Mazda
5-19
NOTE•If the TCS is off when the
engine is turned off, it
automatically activates when
the ignition switch is turned on.
• Leaving the TCS on will
provide the best traction.
047-1A1E
Brake SystemFoot Brake
Your Mazda has power-assisted brakes
that adjust automatically through
normal use.
Should power assist fail, you can stop
by applying greater force than normal
to the brake pedal. But the distance
required to stop will be greater than
usual.
WARNING
!
Driving with the Engine Off:Continuing to drive when the
engine is stalled or turned off is
dangerous. Braking will require
more effort, and the brake’ s
power assist could be depleted if
you pump the brake. This will
cause longer stopping distances
or even an accident. Don’ t
continue driving when the engine
is stalled or turned off, find a safe
place to stop.