ignition MAZDA MODEL 626 2002 Owner's Guide

5-28
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G
If the check engine light flashes
continuously, decrease your speed and
consult an Authorized Mazda Dealer as
soon as possible.





Door-Ajar Warning Light
This warning light comes on when any
door or trunk isn ’t securely closed.





ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’ re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.





Air Bag System Warning Light
If the air bagseat belt pretensioner system
is OK, the warning light comes on when
the ignition switch is turned to the ON
position or after the engine is cranked.
After about 6 seconds it goes out.
A system malfunction is indicated when
the warning light constantly flashes, stays
on or doesn ’t come on at all. If any of
these occur, consult an Authorized Mazda
Dealer as soon as possible. The system
may not work in an accident.
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
Self-Servicing the Air Bag Systems:Self-servicing or tampering with the
systems is dangerous. An air bag
could accidentally activate or become
disabled. This could cause serious
injuries. Never tamper with the
systems and always have an
Authorized Mazda Dealer perform all
servicing and repairs.
WARNING
J94S.book Page 28 Saturday, June 23, 2001 1:04 PM

5-29
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G





Immobilizer System Warning/
Security Indicator Light
Immobilizer system warning light
When the key is in the ignition switch,
this light serves as the immobilizer system
warning light.
If the immobilizer system is working
properly, the light will come on when the
ignition switch is turned to the ON or
START position. The light will go out
when confirmation by the immobilizer
system is completed.
If the light flashes rapidly, fails to come
on, or comes on and stays on, it indicates
a system malfunction. If any of these
occur, contact an Authorized Mazda
Dealer as soon as possible.
Security indicator light
When there is no key in the ignition
switch, and the theft-deterrent system has
been armed, the light will flash once every
3 seconds. This indicates that the system
is working properly.





Headlight High-Beam Indicator
Light
This light indicates one of two things:
• The high-beam headlights are on.
• The turn signal lever is in the flash-to-
pass position.





Rear Window Defroster
Indicator Light
This light comes on when the rear
window defroster is on.
J94S.book Page 29 Saturday, June 23, 2001 1:04 PM

5-30
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G





O/D OFF Indicator Light
This light comes on when the overdrive
has been turned off.





Cruise Set Indicator Light
This light comes on when a cruising speed
is set.





TCS OFF Indicator Light
This light comes on when the ignition
switch is turned to the ON position.
It goes off when the engine is started. It
also comes on when you switch off the
traction control system or when the
system has a malfunction.
If the overdrive-off indicator light
flashes, the transaxle has an electrical
problem. Continuing to drive your
Mazda in this condition could cause
damage to your transaxle. Consult an
Authorized Mazda Dealer as soon as
possible.
CAUTION
NOTE
After starting the engine on very cold
days, the TCS OFF indicator will
remain on and TCS will not operate
until the engine is warm.
J94S.book Page 30 Saturday, June 23, 2001 1:04 PM

5-31
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G





Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened.





Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.
Beeps
J94S.book Page 31 Saturday, June 23, 2001 1:04 PM

5-32
Driving Your Mazda
Form No. 8Q50-EA-01G
Switches and Controls





Headlights
To turn on the lights, turn the knob on the
end of the control lever.





Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.





Headlight High-Low Beam
Push the lever forward for high beams.
Pull it back for low.





Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off OnTaillights
Parking lights
License lights
Side-marker lights Off On On
NOTE
•
If the light switch is left on, the
lights will automatically switch off
30 seconds after turning the ignition
switch to the LOCK position or
removing the key.
The lights will automatically switch
back on when the ignition switch is
turned to the ACC or ON position.
• To prevent discharging the battery,
don ’t leave the lights on while the
engine is off.
Low beams High beams
J94S.book Page 32 Saturday, June 23, 2001 1:04 PM

5-33
Driving Your Mazda
Switches and Controls
Form No. 8Q50-EA-01G





Turn Signal
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change —until the
indicator flashes— and hold it there. It
will return to the off position when
released. In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
Turn and Lane-Change
Signals
NOTE
If an indicator light stays on without
flashing or if it flashes abnormally, the
turn signal bulb may be burned out.
Right turn
Right lane change
OFF
Left lane
change Left turn
Daytime Running Lights
NOTE
The running lights go off when the
parking brake is applied.
J94S.book Page 33 Saturday, June 23, 2001 1:04 PM

5-34
Driving Your Mazda
Switches and Controls
Form No. 8Q50-EA-01G
The ignition switch must be in the ON
position.





Windshield Wipers
Turn the wipers on by pulling the lever
down.
INT — Intermittent
1 — Normal
2 — Fast
Variable-speed intermittent wipers
Set the lever to INT and choose the
interval timing by rotating the ring.
Windshield Wipers and
Wa s h e r
Frozen Washer Fluid:Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don ’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected by a circuit breaker. This
mechanism will automatically stop
operation of the blades, but only for
about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don ’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
OFF
INT 1
2
OFF INT
J94S.book Page 34 Saturday, June 23, 2001 1:04 PM

5-35
Driving Your Mazda
Switches and Controls
Form No. 8Q50-EA-01G
One-touch wipers
For a single wiping cycle, push the lever
up to MIST.





Windshield Washer
Pull the lever toward you and hold it to
spray washer fluid. In the OFF or INT
position, the wipers will be activated until
the lever is released.
If the washer doesn ’t work, inspect the
fluid level (page 8-20). If it ’s OK, consult
an Authorized Mazda Dealer. The rear defroster clears frost, fog, and
thin ice from the rear window.
The ignition switch must be in the ON
position.
Push the switch to turn on the rear
window defroster; the indicator light will
come on.
Push the switch again to turn it off.
Rear Window Defroster
Don
’t use sharp instruments or
window cleaners with abrasives to
clean the inside of the rear window
surface. They may damage the
defroster grid inside the window.
NOTE
This defroster is not designed for
melting snow. If there is an
accumulation of snow on the rear
window, brush it off before using the
defroster.
CAUTION
J94S.book Page 35 Saturday, June 23, 2001 1:04 PM

6-7
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
Mode selector switch
Press the mode selector switch to select
airflow mode (page 6-4).
Air conditioner switch
Press the switch to turn the air conditioner
on. An indicator light on the switch will
illuminate when the fan switch is on.
Press the switch once again to turn the air
conditioner off.Air intake selector switch
This switch controls the source of air
entering the vehicle.
The switch should be kept in the outside
air position under normal conditions.
Press the switch to alternate between the
two positions. The indicator light
illuminates when the recirculated air
position is selected.
Outside air position
This position is automatically selected
when the ignition switch is turned to the
ON position.
Use it for normal ventilation and heating.
The indicator light is out when the outside
air position is selected.
Recirculated air position
This position recirculates air within the
vehicle. Don
’t use the recirculated air
position for long periods when the vehicle
is stopped.
The indicator light is on when the
recirculated air position is selected.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 ° C (32 °F).
J94S.book Page 7 Saturday, June 23, 2001 1:04 PM

6-20
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume knob to turn the
audio system on.
Press the power/volume knob again to
turn the audio system off. Volume adjustmentTo adjust the volume, turn the power/
volume knob.
Turn the power/volume knob to the right
to increase volume, to the left to decrease
it.
Display
Audio control knob
Power/Volume knob
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period when the
engine is not running.
J94S.book Page 20 Saturday, June 23, 2001 1:04 PM