oil MAZDA MODEL CX-3 2015 (in English) Service Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 543 of 671
*Some models.6–65
Maintenance and Care
Appearance Care
Aluminium Wheel Maintenance *
A protective coating is provided over the
aluminium wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolour or stain the
aluminium wheels.
NOTE
Do not use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminium
wheels. They may damage the
coating.
Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
(18-inch wheel vehicle) If your aluminium wheels lose
lustre, apply wax which contains no
polishing powder.
Plastic Part Maintenance
When cleaning the plastic lenses of
the lights, do not use petrol, paraffi n,
rectifi ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signifi cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, fl ush with water
immediately.
If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fl uids such as petrol,
oil, engine coolant, or battery fl uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or fl uids using a soft
cloth immediately.
High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 544 of 671
*Some models.6–66
Maintenance and Care
Appearance Care
Interior Care
WARNING
Do not spray water in the cabin:
Splashing water on electrical parts
such as the audio unit and switches
is dangerous as it could cause a
malfunction or a fi re.
Instrument panel Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
instrument panel. They will damage and
discolour the instrument panel. If these
solutions get on the instrument panel, wipe
them off immediately.
CAUTION
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discolouration,
wrinkling, cracks and peeling.
Instrument panel top
When cleaning, it is recommended that
you use a clean towel dampened in a
mild detergent to remove soiling.
If the surface is rubbed harshly, it could
result in the surface being damaged
leaving white scratch marks.
Cleaning the Upholstery and
Interior Trim
Vinyl
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather
*
Remove dust and sand fi rst using a
vacuum cleaner or other means, then wipe
dirt off using a soft cloth with a leather
cleaner or a soft cloth soaked in mild soap.
Wipe off the remaining cleaner or soap
using a cloth soaked in clean water and
wrung out well.
Remove moisture with a dry, soft cloth
and allow the leather to further dry in a
well-ventilated, shaded area. If the leather
gets wet such as from rain, also remove
moisture and dry it as soon as possible.
NOTE
Because genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
To maintain the quality for as long
as possible, periodical maintenance,
about twice a year, is recommended.
Sand and dust on the seat surface
may damage the overcoat of the
genuine leather surfaces and
accelerate wear.
Greasy soiling on genuine leather
may cause molding and stains.
Rubbing hard with a stiff brush or
cloth may cause damage.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 545 of 671
6–67
Maintenance and Care
Appearance Care
NOTE
Do not wipe the leather using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
or petrol. Otherwise, it may cause
discolouration or stains.
If the seats get wet, promptly remove
moisture with a dry cloth. Remaining
moisture on the surface may cause
deterioration such as hardening and
shrinkage.
Exposure to direct sunlight for long
periods may cause deterioration
and shrinkage. When parking the
car under direct sunlight for long
periods, shade the interior using
sunshades.
Do not leave vinyl products on
the seats for long periods as they
may affect the leather quality and
colouring. If the cabin temperature
becomes hot, the vinyl may
deteriorate and adhere to the genuine
leather.
Fabric and Synthetic Leather
Allowing the material to remain dirty
makes it hard to clean later and may cause
stains or discolouration. Clean as soon as
possible.
Fabric
1. Clean the soiled area by lightly dabbing
it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
CAUTION
Use only recommended cleaners
and procedures. Others may affect
appearance and fi re-resistance.
Synthetic leather
1. Remove dust and sand using a vacuum
cleaner.
2. Wipe the soiled area with a soft cloth
soaked in a mild detergent (approx.
5%) diluted in water.
3. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
Panel
When the interior panels need to be
cleaned, use soft material such as a soft
cloth soaked in clean water and wrung
out well and lightly wipe off dirt from
the surface. If a panel requires further
cleaning, use the following procedure.
1. Wipe dirt off using a soft cloth soaked
in mild detergent (about 5% solution).
2. Wipe off any remaining detergent
using a cloth soaked in clean water and
wrung out well.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 546 of 671
*Some models.6–68
Maintenance and Care
Appearance Care
NOTE
Do not wipe leather parts using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
or petrol. Otherwise, it may cause
discolouration or stains.
Scratches or nicks on the panels and
metallic trim resulting from the use
of a hard brush or cloth may not be
repairable.
Be particularly careful when cleaning
high lustre panels and metallic trim
as they can be easily scratched.
Maintenance of the Active Driving
Display*
The combiner and mirror surface have a
special coating. When cleaning, do not use
a hard or rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving display,
wipe it off immediately. Otherwise, the
combiner and mirror could be damaged
and the surface coating could be scratched.
Use a fi ne, soft cloth such as those used
for cleaning eyeglasses.
Cleaning the Lap/Shoulder Belt
Webbing
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Do not bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is no
remaining moisture before retracting them.
WARNING
Have an expert repairer, we
recommend an Authorised Mazda
Repairer replace damaged seat belts
immediately:
Using damaged seat belts is dangerous.
In a collision, damaged belts cannot
provide adequate protection.
Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy fi lm, clean them with
glass cleaner. Follow the directions on the
container.
CAUTION
Do not scrape or scratch the inside of
the window glass. It could damage
the thermal fi laments and the aerial
lines.
When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water, gently
wiping the thermal fi laments and the
aerial lines.
Use of glass cleaning products could
damage the thermal fi laments and the
aerial lines.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 567 of 671
7–21
If Trouble Arises
Flat Tyre
9. Remove the wheel nuts by turning
them anticlockwise; then remove the
wheel and centre cap.
Mounting the Spare Tyre
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
WARNING
Make sure the mounting surfaces of
the wheel, hub and wheel nuts are
clean before changing or replacing
tyres:
When changing or replacing a tyre,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The wheel
nuts could loosen while driving and
cause the tyre to come off, resulting in
an accident.
2. Mount the spare tyre. 3. Install the wheel nuts with the bevelled
edge inward; tighten them by hand.
WARNING
Do not apply oil or grease to wheel
nuts and bolts and do not tighten the
wheel nuts beyond the recommended
tightening torque:
Applying oil or grease to wheel nuts
and bolts is dangerous. The wheel nuts
could loosen while driving and cause
the tyre to come off, resulting in an
accident. In addition, wheel nuts and
bolts could be damaged if tightened
more than necessary.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 583 of 671
7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-28 . If it's low, add the appropriate amount of engine oil
while being careful not to overfi ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Light
The light fl ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can fi nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-29 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 586 of 671
*Some models.7–40
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Automatic
Transaxle Warning
Light
*
The light illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning light illuminates, the transaxle has an electrical
problem. Continuing to drive your Mazda in this condition could cause damage to your
transaxle. Consult an expert repairer, we recommend an Authorised Mazda Repairer as
soon as possible.
4WD Warning
Light*
When the light is turned on
If the 4WD warning light illuminates, contact an expert repairer, we recommend an
Authorised Mazda Repairer.
Illuminates when there is an abnormality with the 4WD system. Illuminates if there is too much difference in tyre radius between the front and rear wheels.
When the light is fl ashing
Park the vehicle in a safe place. After a few moments, if the warning light stops fl ashing,
you can resume driving. If the light does not stop fl ashing, contact an expert repairer, we
recommend an Authorised Mazda Repairer.
Flashes when the differential oil temperature is abnormally high. Flashes when there is a continuous large difference between front and rear wheel rotation,
such as when trying to pull away from an icy surface or when trying to remove the vehicle
from mud, sand or similar conditions.
Air Bag/Seat Belt
Pretensioner System
Warning Light A system malfunction is indicated if the warning light constantly fl ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 632 of 671
9–6
Specifi cations
Specifi cations
Lubricant Quality
Engine oil *1 Europe Except Europe
SKYACTIV-G 2.0 Recommended Oils *2 Oil Quality
Mazda Original Oil Supra 0W-20
API SG/SH/SJ/SL/SM/SN
*4 or
ILSAC GF-II/GF-III/GF-IV/GF-V Mazda Original Oil Ultra 5W-30
Alternative Oil Quality *3
API SL/SM/SN or ACEA
A3/A5 0W-20
5W-30
SKYACTIV-D 1.5 Recommended Oils
*2 Oil Quality
Mazda Original Oil Supra DPF 0W-30
ACEA C3
0W-30 / 5W-30 Mazda Original Oil Ultra DPF 5W-30
Alternative Oil Quality
*3
ACEA C3 0W-30
5W-30
*1 Refer to the recommended SAE viscosity numbers on page 6-23 .
*2 Mazda Original Oils are specially designed/tested for the respective engine. For optimum performance we
recommend to use Mazda Original Oils at all times.
*3 If you are unable to fi nd a Mazda Original Oil, alternative oils meeting the listed specifi cation may also be used.
*4 Use API SM/SN in Kazakhstan.
Do not use oils which do not meet the above specifi cation or requirements. Use of
unsuitable oil may lead to engine damage which is not covered by the Mazda Warranty.
Lubricant Classifi cation
Coolant FL-22 type
Manual transaxle oil API Service GL-4
SAE 75W-80
Automatic transaxle
fl uid Mazda Original Oil ATF-FZ
Transfer case oil Mazda Long Life Hypoid Gear Oil SG1
Rear differential oil Mazda Long Life Hypoid Gear Oil SG1
Brake/Clutch fl uid SAE J1703 or FMVSS116 DOT-3 or DOT-4
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 633 of 671
*Some models.9–7
Specifi cations
Specifi cations
Capacities
(Approximate Quantities)
Item Capacity
Engine oil SKYACTIV-G
2.0 With oil fi lter replacement 4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil fi lter replacement 4.0 L (4.2 US qt, 3.5 Imp qt)
SKYACTIV-D
1.5 With oil fi lter replacement 5.1 L (5.4 US qt, 4.5 Imp qt)
Without oil fi lter replacement 4.7 L (5.0 US qt, 4.1 Imp qt)
Coolant SKYACTIV-G
2.0 Manual transaxle 5.6 L (5.9 US qt, 4.9 Imp qt)
Automatic
transaxle Saudi Arabia 6.1 L (6.4 US qt, 5.4 Imp qt)
Right-hand drive
model 5.9 L (6.2 US qt, 5.2 Imp qt)
Except above 5.8 L (6.1 US qt, 5.1 Imp qt)
SKYACTIV-D
1.5 For engine Manual transaxle 6.6 L (7.0 US qt, 5.8 Imp qt)
Automatic
transaxle 6.8 L (7.2 US qt, 6.0 Imp qt)
For water-cooled charge air cooler 2.1 L (2.2 US qt, 1.8 Imp qt)
Manual transaxle oil 2WD SKYACTIV-G 2.0 1.70 L (1.80 US qt, 1.50 Imp qt)
SKYACTIV-D 1.5 1.65 L (1.74 US qt, 1.45 Imp qt)
4WD 1.70 L (1.80 US qt, 1.50 Imp qt)
Automatic transaxle fl uid 7.8 L (8.2 US qt, 6.9 Imp qt)
Transfer case oil 0.40 L (0.42 US qt, 0.35 Imp qt)
Rear differential oil 0.35 L (0.37 US qt, 0.31 Imp qt)
Fuel tank 2WD 48.0 L (12.7 US gal, 10.6 Imp gal)
4WD 44.0 L (11.6 US gal, 9.68 Imp gal)
Check oil and fl uid levels with dipsticks or reservoir gauges.
Dimensions
Item Vehicle specifi cation
Overall length 4,275 mm (168.3 in)
Overall width 1,765 mm (69.5 in)
Overall height 1,535 mm (60.4 in)
Front tread 1,525 mm (60.0 in)
Rear tread 1,520 mm (59.8 in)
Wheelbase 2,570 mm (101.2 in)
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 649 of 671
10–3
Index
C
Capacities .............................................. 9-7
Carbon Monoxide ............................... 3-27
Cargo Sub-Compartment .................. 5-153
Cell Phones ........................................... 8-4
Child Restraint
Categories of child-restraint
systems .......................................... 2-26
Child-restraint precautions ............ 2-21
Child-restraint system installation ... 2-26
Child-restraint system suitability for
various seat positions table............ 2-31
Installing child-restraint systems... 2-35
Child Safety Locks for Rear Doors ..... 3-19
Clock ................................................... 5-30
Collision warning ................................ 7-54
Coming Home Light System .............. 4-63
Control Status Display ........................ 4-89
Cruise Control ................................... 4-158
Cruise Control Switch ................. 4-158
Cruise Main Indicator Light (Amber)/
Cruise Set Indicator Light
(Green) ........................................ 4-159
Cruise Control Set Vehicle Speed
Display ................................................ 4-31
Cup Holder ........................................ 5-150
D
Defogger
Mirror ............................................ 4-74
Rear window ................................. 4-73
Diesel Particulate Filter ..................... 4-167
Dimensions ........................................... 9-7
Direct Mode
Automatic transaxle ...................... 4-56
Direction Indicators ............................ 4-67
Distance Recognition Support System
(DRSS) .............................................. 4-118
Indication on display ................... 4-119
Door Locks .......................................... 3-10
Drive selection .................................... 4-93 Driving In Flooded Area ..................... 3-52
Driving Tips
Automatic transaxle ...................... 4-57
Driving in fl ooded area.................. 3-52
Floor mat ....................................... 3-48
Hazardous driving ......................... 3-47
Rocking the vehicle ....................... 3-49
Running-in..................................... 3-46
Saving fuel and protection of the
environment................................... 3-46
Turbocharged vehicles (SKYACTIV-D
1.5) ................................................ 3-53
Winter driving ............................... 3-49
Dynamic Stability Control (DSC) ....... 4-84
TCS/DSC Indicator Light ............. 4-84
E
Effectiveness Display .......................... 4-92
Electronic steering lock warning beep ... 7-54
Emergency Starting
Push-Starting ................................. 7-27
Running Out of Fuel (SKYACTIV-D
1.5) ................................................ 7-28
Starting a Flooded Engine
(SKYACTIV-G 2.0) ...................... 7-27
Emergency Stop Signal System .......... 4-79
Emergency Towing
Towing Description ....................... 7-31
Towing/Tiedown Hooks ................ 7-32
Emission Control System (SKYACTIV-D
1.5) ...................................................... 3-26
Emission Control System (SKYACTIV-G
2.0) ...................................................... 3-25
Ending Display .................................... 4-92
Engine
Bonnet release ............................... 6-19
Coolant .......................................... 6-29
Engine Compartment Overview .... 6-21
Exhaust gas.................................... 3-27
Oil .................................................. 6-23
Starting ............................................ 4-5
Essential information ............................ 6-2
$ 9 @ & ; & & % @ & E J U J P O J O E C