cooling MAZDA MODEL CX-3 2015 Owners Manual (in English)

3–27
Before Driving
Fuel and Emission
Engine Exhaust (Carbon monoxide)
WARNING
Do not drive your vehicle if you smell exhaust gas inside the vehicle:
Engine exhaust gas is dangerous. This gas contains carbon monoxide (CO), which is
colourless, odourless, and poisonous. When inhaled, it can cause loss of consciousness
and death. If you smell exhaust gas inside the vehicle, keep all windows fully open and
contact an expert repairer, we recommend an Authorised Mazda Repairer immediately.
Do not run the engine when inside an enclosed area:
Running the engine inside an enclosed area, such as a garage, is dangerous. Exhaust
gas, which contains poisonous carbon monoxide, could easily enter the cabin. Loss of
consciousness or even death could occur.
Open the windows or adjust the heating or cooling system to draw fresh air when idling
the engine:
Exhaust gas is dangerous. When the vehicle is stopped with the windows closed and
the engine running for a long time even in an open area, exhaust gas, which contains
poisonous carbon monoxide, could enter the cabin. Loss of consciousness or even death
could occur.
Clear snow from underneath and around your vehicle, particularly the tail pipe, before
starting the engine:
Running the engine when a vehicle is stopped in deep snow is dangerous. The exhaust
pipe could be blocked by the snow, allowing exhaust gas to enter the cabin. Because
exhaust gas contains poisonous carbon monoxide, it could cause loss of consciousness
or even death to occupants in the cabin.
$9@&;&&%@&EJUJPOJOEC







4–12
When Driving
Start/Stop Engine
NOTE
  The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
  When the push button start is pressed
from ON to ACC or OFF, the KEY
indicator light (green) may fl ash for
approximately 30 seconds indicating
that the remaining battery power of
the key is low.
 Replace with a new battery before
the key becomes unusable.
 Refer to Key Battery Replacement on
page 6-39 .
 (Automatic transaxle) If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
$9@&;&&%@&EJUJPOJOEC







4–14
When Driving
Start/Stop Engine
Automatic transaxle
1. Engine idling stops when the brake pedal is depressed while the vehicle is driven (except
for driving in the R or M position second gear fi xed mode) and the vehicle is stopped.
2. The engine restarts automatically when the brake pedal is released with the selector lever
in the D or M position (not in second gear fi xed mode).
3. If the selector lever is in the N or P position, the engine does not restart when the brake
pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear fi xed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depressed when shifting the
selector lever while engine idling is stopped.)
Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
 


(SKYACTIV-G 2.0)
 The engine is warmed up.



(SKYACTIV-D 1.5)



 
 The engine is not cold.


 
 The fuel injection amount learning, which is performed periodically and automatically,
is not being performed.
 


 The engine has been started and the vehicle is driven for a certain period.



 The engine is started with the bonnet closed.



 The battery is in good condition.



 All doors, liftgate, and bonnet are closed.



 The driver's seat belt is fastened.



 The air conditioner is not operating with the airfl ow mode dial in the position (A/C
ON).
 


(Automatic air-conditioning)



 
 The temperature setting dial for the air conditioning is set to a position other than
maximum cooling (A/C ON).
 

 
 The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
 


 The i-stop warning light (amber) is not turned on/fl ashing.



 The keyless entry & push button start system functions are normal.



 The brake vacuum is suffi ciently high.



 The steering wheel is not being operated.
$9@&;&&%@&EJUJPOJOEC







4–15
When Driving
Start/Stop Engine
 


(Manual transaxle)



 
 The vehicle speed is 3 km/h (1.8 mph) or less.


 
 The shift lever is in the neutral position.


 
 The clutch pedal is not depressed.




(Automatic transaxle)



 
 The vehicle is stopped.


 
 The selector lever is in the D or M position (not in second gear fi xed mode).


 
 The automatic transaxle fl uid has warmed up suffi ciently.


 
 The automatic transaxle fl uid temperature is not abnormally high.


 
 The steering wheel is almost in the straight-ahead position (idling may not stop even
with the steering wheel in the straight-ahead position if force is applied to the steering
wheel. Release the force applied to the steering wheel to stop engine idling).
 

 
 The vehicle is stopped by depressing the brake pedal.


 
 Emergency braking is not applied.
When the system is not operable
Engine idling does not stop in the following conditions:
 


 The vehicle is stopped but the engine is kept idling.



 The air-conditioner is operating with the airfl ow mode dial in the position (A/C ON).



(Automatic air-conditioning)



 
 The temperature setting dial for the air conditioning is set to the maximum cooling (A/C
ON) position.
 

 
 There is a large difference between the cabin temperature and the set temperature of the
air-conditioner.
 


 The ambient temperature is extremely high or low.



 The atmospheric pressure is low (when driving at high altitudes).



(Automatic transaxle)



 
 The vehicle is stopped on a steep incline.


 
 The steering wheel is not in the straight-ahead position while the vehicle is stopped.




(SKYACTIV-D 1.5)
 The particulate matter (PM) is being removed by the diesel particulate fi lter (DPF).
$9@&;&&%@&EJUJPOJOEC







4–16
When Driving
Start/Stop Engine
NOTE
Under the following conditions, a period of time is required to stop engine idling
 
 The battery power is depleted for some reasons such as the vehicle has not been driven
for a long period.
  The ambient temperature is high or low. 
 After the battery terminals are disconnected for some reasons such as for battery
replacement.
 (SKYACTIV-D 1.5) After PM removal is performed by the diesel particulate fi lter (DPF).
Engine does not restart
If the following operations are performed while the idling is stopped, the engine will not
restart for safety reasons. In such cases, start the engine using the normal method.
 
 The bonnet is opened. 
(European model) The driver's seat belt is unfastened and the driver's door is opened. 
(Except European model)




(Manual transaxle)
 With the shift lever in a position other than neutral, the driver's seat belt is
unfastened and the driver's door is opened.
 


(Automatic transaxle)
 With the selector lever in the D or M (not in second gear fi xed mode), the driver's
seat belt is unfastened and the driver's door is opened.
Engine-stop period is short or time until next engine idle stop is long
 
 The ambient temperature is high or low. 
 The battery power is depleted. 
 Power consumption by the vehicle's electrical parts is high.
Engine restarts automatically while engine idling is stopped
Under the following conditions, the engine restarts automatically.
 
 The i-stop OFF switch is pressed until the beep sounds.

 The air-conditioner is operated with the airfl ow mode dial in the position (A/C
ON).
 (Automatic air-conditioning)




 The temperature setting dial of the air-conditioner is set to maximum cooling (A/C
ON).
 


 The cabin temperature is largely different from the set temperature of the air-
conditioner.
$9@&;&&%@&EJUJPOJOEC







5–2
Interior Features
Air-Conditioning System
Operating Tips
 












 Operate the air-conditioning system with
the engine running.
 


 To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time with the
ignition switched ON when the engine is
not running.
 


(With i-stop)
 The airfl ow amount may decrease
slightly while the i-stop function is
operating.
 


 Clear all obstructions such as leaves,
snow and ice from the bonnet and the
air inlet in the cowl grille to improve the
system effi ciency.




 Use the air-conditioning system to defog
the windows and dehumidify the air.
 


 The recirculate mode should be used
when driving through tunnels or while in
a traffi c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
 


 Use the outside air position for
ventilation or windscreen defrosting.
 


 If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the air-conditioning system.
 


 Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
 


 Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
effi cient.

 The refrigerant specifi cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before refi lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
  For details, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Label
$9@&;&&%@&EJUJPOJOEC







5–7
Interior Features
Air-Conditioning System
Recirculated air position ()
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
Heating
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
NOTE
  If the windscreen fogs up easily, set
the mode selector dial to the
position.  If cooler air is desired at face level,
set the mode selector dial to the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffi c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
fl ashing (page 4-36 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air
conditioning off (page 7-29 ).
$9@&;&&%@&EJUJPOJOEC







5–8
Interior Features
Air-Conditioning System
NOTE
  When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then set the fan control dial
to position 4.
  If warmer air is desired at fl oor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Ventilation
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
Windscreen Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. (Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position. 4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
WARNING
Do not defog the windscreen using the
position with the temperature
control set to the cold position:
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set the
temperature control to the hot or warm
position when using the
position.
NOTE
  For maximum defrosting, turn on the
air conditioner, set the temperature
control dial to the extreme hot
position, and the fan control dial to
position 4.
  If warm air is desired at the fl oor, set
the mode selector dial to the
position. (Type A)
 In the position, the outside air
position is automatically selected.
The air intake selector cannot be
changed to the recirculated air
position.
$9@&;&&%@&EJUJPOJOEC







5–11
Interior Features
Air-Conditioning System
Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and anticlockwise for
cold.
Fan control dial
The fan has seven speeds.
AUTO position
The amount of airfl ow will be
automatically controlled in accordance
with the set temperature.
Except AUTO position
The airfl ow amount can be adjusted to the
desired level by turning the dial.
0 position
To turn off the system, set the dial to 0
position.
Mode selector dial
Turn the mode selector dial to select
airfl ow mode (page 5-4 ).
AUTO position
The airfl ow mode automatically adjusts to
the selected temperature.
Except AUTO position
The desired airfl ow position can be
selected by turning the dial.
NOTE
  With the airfl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and
air at a comparably lower
temperature will fl ow through the
central, left and right vents.
  When the fan control dial is ON, and
the mode selector dial is in the
position, the air conditioner is
automatically turned on and the
outside air position is automatically
selected to defrost the windscreen.
A/C switch
The air conditioning (cooling/
dehumidifying functions) can be turned on
or off by pressing the switch while the fan
control dial is at a position other than 0.
The indicator light turns on while the air
conditioning is operating.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traffi c (high engine exhaust
areas) or when quick cooling is desired.
$9@&;&&%@&EJUJPOJOEC







6–4
Maintenance and Care
Scheduled Maintenance
Europe
Maintenance Interval Number of months or kilometres (miles), whichever comes fi rst.
Months 12 24 36 48 60 72 84 96 108
×1000 km 20 40 60 80 100 120 140 160 180
×1000 miles 12.5 25 37.5 50 62.5 75 87.5 100
112.5
SKYACTIV-G 2.0
Spark plugs *1 Replace every 120,000 km (75,000 miles).
Air fi lter
*2 R R R
Evaporative system (if installed) I I I
SKYACTIV-D 1.5
Fuel fi lter D D R D D R D D R
Fuel injection system
*3 I I I
Air fi lter
*2 C C R C C R C C R
SKYACTIV-G 2.0 AND SKYACTIV-D 1.5
Drive belts
*4 I I I
Engine oil & fi lter Flexible
*5 Replace when indicator is ON. (Max interval:12
months/20,000 km (12,500 miles))
Other than
fl exible
*6*7 R R R R R R R R R
Cooling system I I I I
Engine coolant
*8 Replace at fi rst 200,000 km (125,000 miles) or 10 years; after
that, every 100,000 km (62,500 miles) or 5 years.
Fuel lines and hoses I I I I
Battery
*9 I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I
Brake fl uid
*10 R R R R
Parking brake I I I I I I I I I
Disc brakes I I I I I I I I I
Steering operation and linkages I I I I
Manual transaxle oil Replace every 180,000 km (112,500 miles).
Rear differential oil
*11*12
Transfer oil *12
Front and rear suspension, ball joints and wheel
bearing axial play I I I I
Driveshaft dust boots I I I I
Exhaust system and heat shields Inspect every 80,000 km (50,000 miles) or 5 years.
Bolts and nuts on chassis and body T T T T
Body condition (for rust, corrosion and
perforation) Inspect annually.
$9@&;&&%@&EJUJPOJOEC