engine coolant MAZDA MODEL CX-3 2019 (in English) Owner's Manual

NOTE
Changing the coolant should be done by
an Authorized Mazda Dealer.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year―at the beginning of the
winter season―and before traveling where
temperatures may drop below freezing.

Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.

The coolant should be at full in the
radiator and between the F and L marks on
the coolant reservoir when the engine is
cool.

Cooling system cap Coolant reservoir
Cooling fan
If it is at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
Securely tighten the coolant reservoir tank
cap after adding coolant.
CAUTION
 Radiator coolant will damage paint.
Rinse it off quickly if spilled.
 If the “FL22” mark is shown on or near
the cooling system cap, use of FL-22 is
recommended when replacing engine
coolant. Using engine coolant other than
FL-22 may cause serious damage to the
engine and cooling system.

If the coolant reserv oir is empty or new
coolant is required frequently, consult an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
6-26
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

▼Aluminum Wheel Maintenance*
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolor or stain the
aluminum wheels.
NOTE
•Do not use a wire brush or any abrasive
cleaner, polishing compound, or solvent
on aluminum wheels. They may damage
the coating.
•Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be sure to
clean the wheels after driving on dusty
or salted roads to help prevent
corrosion.
•Avoid washing your vehicle in an
automatic car wash th
at uses high-speed
or hard brushes.
•(18-inch wheel vehicle)
If your aluminum wheels lose luster,
apply wax which contains no polishing
powder.
▼ Plastic Part Maintenance
•When cleaning the plastic lenses of the
lights, do not use gasoline, kerosene,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolor or damage the
surfaces resulting in a
significant loss in
functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
•If plastic parts s uch as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
gasoline, oil, engine coolant, or battery
fluid, it could cause discoloration,
staining, or paint peeling. Wipe off any
such chemical agents or fluids using a
soft cloth immediately.
•High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
•Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
•In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result in
deformation of plastic parts or paint
damage.
Maintenance and Care
Appearance Care
*Some models.6-59
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Overheating
If the high engine coolant temperature
warning light turns on, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WA R N I N G
Pull over to a safe location, then switch
the ignition off and make sure the fan is
not running before attempting to work
near the cooling fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if the
engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and radiator
are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot out
under pressure and cause serious injury.
Open the hood ONLY after steam is no
longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the high engine coolant temperature
warning light turns on:

1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic transaxle in park (P), a manual
transaxle in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine
compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.

If neither coolant nor steam is
escaping:
Open the hood and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
6. Make sure the cooling fan is operating, then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If Trouble Arises
Overheating
7-22
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

If it is low, look for coolant leaks from
the radiator and hoses.

If you find a leak or other damage, or if
coolant is still leaking:
Stop the engine and call an Authorized
Mazda Dealer.
Cooling system cap Coolant reservoir
Cooling fan
If you find no problems, the engine is
cool, and no leaks are obvious:
Carefully add coolant as required (page
6-25).
CAUTION
If the engine continues to overheat or
frequently overheats, have the cooling
system inspected. The engine could be
seriously damaged unless repairs are
made. Consult an Authorized Mazda
Dealer.
If Trouble Arises
Overheating
7-23
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

SignalWarning
Charging System Warn-
ing Light If the warning light illuminates
while driving, it indicates a malfunction of the alter-
nator or of the charging system.
Drive to the side of the road and park off the right-of-way. Co nsult an Authorized
Mazda Dealer.CAUTION
Do not continue driving when the charging system warning light is illuminated be‐
cause the engine could stop unexpectedly.
Engine Oil Warning Light This warning light indicates
low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in extensive
engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way o n level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the oil pan.
3. Inspect the engine oil level (page 6-25). If it's low, add th e appropriate amount of
engine oil while being careful not to overfill.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.

If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an Authorized Mazda
Dealer.
(Red)
High Engine Coolant
Temperature Warning Light The light flashes when the engine coolant temperature is extrem
ely high, and illumi-
nates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine l oad until you can find a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place immedi-
ately and stop the engine.
Refer to Overheating on page 7-22.
CAUTION
Do not drive the vehicle with the high engi ne coolant temperature warning light illumi‐
nated. Otherwise, it could resu lt in damage to the engine.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-29
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Message Indicated on Display*
If a message is displayed in the center display (Type B audio), take appropriate action (in a
calm manner) according to the displayed message.

(Display example)
▼ Stop Vehicle in Safe Place Immediately
If the following messages are displayed in the center display (
Type B audio), a vehicle
system may be malfunctioning. St op the vehicle in a safe place and contact an Authorized
Mazda Dealer.
Display Indicated Condition
Displays if the engine coolant temperature has increased excess ively.
Displays if the charging system has a malfunction.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-41
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Specifications
▼Engine
Item
Specification
Type DOHC-16V in-line, 4-cylinder
Bore × Stroke 83.5 × 91.2 mm (3.29 × 3.59 in)
Displacement 1,997.6 ml (1,997.6 cc)
Compression ratio 13.0
▼Electrical System
Item
Specification
Battery Canada
12V-65Ah/20HR
Except Canada 12V-60Ah/20HR or 12V-65Ah/20HR
Spark-plug number Mazda Genuine spark
plug
*1PE5R-18-110 or PE5S-18-110
*1 The spark plugs provide the SKY
ACTIV-G its optimum performance. Consult an Authorized Mazda Dealer
for details.
CAUTION
When cleaning the iridium plugs, do not use a wire brush. The fine particulate coating on the
iridium alloy and platinum tips could be damaged.
▼ Lubricant Quality
Lubricant
Specification
Engine oil Refer to Recommended Oil on page 6-22.
Coolant FL-22 type
Manual transaxle oil API Service
GL-4
SAE 75W-80
Automatic transaxle fluid Mazda Genuine ATF-FZ
Transfer case oil Mazda Long Life Hypoid Gear Oil SG1
Rear differential oil Mazda Long Life Hypoid Gear Oil SG1
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
NOTE
Refer to Introduction on (page 6-2) for owner's responsibility in protecting your investment.
Specifications
Specifications
9-4
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

▼Capacities
(Approximate Quantities)
Item
Capacity
Engine oil With oil filter replacement
4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil filter replacement 4.0 L (4.2 US qt, 3.5 Imp qt)
Coolant Manual transaxle
5.6 L (5.9 US qt, 4.9 Imp qt)
Automatic transaxle U.S.A. and Canada
5.9 L (6.2 US qt, 5.2 Imp qt)
Mexico 6.1 L (6.4 US qt, 5.4 Imp qt)
Manual transaxle fluid 1.70 L (1.80 US qt, 1.50 Imp qt)
Automatic transaxle fluid 7.8 L (8.2 US qt, 6.9 Imp qt)
Transfer case oil 0.40 L (0.42 US qt, 0.35 Imp qt)
Rear differential oil 0.35 L (0.37 US qt, 0.31 Imp qt)
Fuel tank 2WD
48.0 L (12.7 US gal, 10.6 Imp gal)
AWD 45.0 L (11.9 US gal, 9.90 Imp gal)
Check oil and fluid levels with dipsticks or reservoir gauges.
▼Dimensions
U.S.A. and Canada
Item
Vehicle specification
Overall length 4,275 mm (168.3 in)
Overall width 1,765 mm (69.5 in)
Overall height 1,550 mm (61.0 in)
Front tread 1,525 mm (60.0 in)
Rear tread 1,520 mm (59.8 in)
Wheelbase 2,570 mm (101.2 in)

Mexico
ItemVehicle specification
Overall length 4,275 mm (168.3 in)
Overall width 1,765 mm (69.5 in)
Overall height 1,545 mm (60.8 in)
Front tread 1,525 mm (60.0 in)
Rear tread 1,520 mm (59.8 in)
Wheelbase 2,570 mm (101.2 in)
Specifications
Specifications
9-5
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Index
Driving on uneven road...............3-49
Floor mat..................................... 3-44
Hazardous driving....................... 3-44
Overloading................................. 3-48
Rocking the vehicle..................... 3-45
Saving fuel and protection of the
environment................................. 3-43
Winter driving............................. 3-45
Dynamic Stability Control (DSC)..... 4-70 TCS/DSC Indicator Light............4-70
E
Electric Parking Brake (EPB)........... 4-57
Electric Parking Brake (EPB) Warning
Beep...................................................7-45
Emergency Starting
Push-Starting............................... 7-21
Starting a Flooded Engine........... 7-21
Emergency Towing Tiedown Hooks....... .................... 7-25
Towing Description..................... 7-24
Emission Control System..................3-25
Ending Screen Display......................4-72
Engine Coolant.........................................6-25
Engine Compartment
Overview..................................... 6-21
Exhaust gas.................................. 3-26
Hood release............................ .... 6-19
Oil................................................ 6-22
Essential information.......................... 6-2
Event Data Recorder......................... 8-21
Excessive Speed Warning................. 7-47
Exhaust Gas...................................... 3-26
Exterior Care..................................... 6-54 Aluminum Wheel Maintenance... 6-59
Bright-Metal Maintenance...........6-58
Maintaining the Finish................ 6-55
Plastic Part Maintenance............. 6-59
F
Flasher
Hazard warning........................... 4-55
Headlights.................................... 4-43
Flat Tire............................................... 7-3
Mounting the Spare Tire............. 7-13
Removing a Flat Tire.................... 7-9
Floor Mat.......................................... 3-44
Fluid
Brake/Clutch................................ 6-27
Washer......................................... 6-27
Fluids Classification................................. 9-4
Fog Lights......................................... 4-48
Foot Brake.........................................4-56
Forward Sensing Camera (FSC)..... 4-130
Front Seat............................................ 2-5
Fuel
Filler lid and cap......................... 3-27
Gauge........................................... 4-16
Requirements............................... 3-24
Tank capacity.................................9-5
Fuel Consumption Display............... 4-71
Fuel Economy Monitor..................... 4-71
Ending screen display................. 4-72
Fuel consumption display............4-71
Fuses.................................................. 6-48 Panel description......................... 6-50
Replacement................................ 6-48
G
Gauges............................................... 4-11
Glove Compartment........................ 5-132
H
Hazardous Driving............................ 3-44
Hazard Warning Flasher....................4-55
HeadlightsComing home light......................4-46
10-4
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Index
Control......................................... 4-43
Flashing....................................... 4-46
High-low beam............................ 4-46
Leaving home light..................... 4-47
Leveling....................................... 4-47
Head Restraint................................... 2-12
High Beam Control System
(HBC)................................................ 4-81
Hill Launch Assist (HLA)................ 4-65
Hood Release.................................... 6-19
Horn...................................................4-55
I
If a Warning Light Turns On or
Flashes............................................... 7-27
If the Active Driving Display does not
operate............................................... 7-49
Ignition Switch............................................ 4-4
Ignition not switched off (STOP)
warning beep..................................... 7-44
Illuminated Entry System............... 5-127
Immobilizer System.......................... 3-39
Indicator Lights................................. 4-26 Low engine coolant
temperature.................................. 4-29
Wrench......................................... 4-29
Inspecting Brak e/Clutch Fluid
Level.................................................. 6-27
Inspecting Coolant Leve l.................. 6-25
Inspecting Engine Oil Level............. 6-25
Inspecting Washer Fluid Level......... 6-27
Instrument Cluster...... ....................... 4-11
Interior Care...................................... 6-60 Active driving display
maintenance................................. 6-62
Cleaning the floor mats............... 6-63
Cleaning the window interiors.....6-62
Instrument panel top
maintenance................................. 6-62
Leather upholstery
maintenance................................. 6-61
Panel maintenance....................... 6-62
Plastic part maintenance.............. 6-62
Seat belt maintenance..................6-60
Upholstery and synthetic leather
maintenance................................. 6-61
Vinyl upholstery maintenance..... 6-61
Interior Lights................................. 5-126 Luggage Compartment Light.....5-126
Map Lights................................ 5-126
Overhead Lights........................ 5-126
i-ACTIVSENSE................................ 4-77
Active Safety Technology........... 4-77
Adaptive Front Lighting System
(AFS)........................................... 4-80
Advanced Smart City Brake Support
(Advanced SCBS)..................... 4-119
Blind Spot Monitoring (BSM).....4-90
Camera and sensors..................... 4-78
Distance Recognition Support System
(DRSS).......................................4-102
Forward Sensing Camera
(FSC)......................................... 4-130
High Beam Control System
(HBC).......................................... 4-81
Lane Departure Warning System
(LDWS)....................................... 4-84
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)..................4-107
Pre-Crash Safety Technology...... 4-78
Radar Sensors (Rear).................4-138
Radar sensor (front)...................4-135
Rear Cross Traffic Alert
(RCTA)...................................... 4-104
Smart Brake Support (SBS)...... 4-127
Smart City Brake Support
(SCBS)....................................... 4-123
Traffic Sign Recognition System
(TSR)........................................... 4-96
10-5
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14