light MAZDA MODEL CX-30 2019 Owners Manual (in English)

1. “BRAKE!” message is displayed
NOTE
xThe collision warning sound is
activated intermittently while the SBS
brake or brake assist (SBS brake
assist) is operating.
xThe operation distance and volume
of the collision warning can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Stopping the Smart Brake Support
(SBS) System Operation
The SBS can be changed to inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS is cancelled, the SBS
OFF indicator light turns on.
NOTE
When the ignition is switched OFF
while the SBS is cancelled, the SBS is
automatically enabled the next time
the ignition is switched ON.
Smart Brake Support
[Rear] (SBS-R)
*
▼Smart Brake Support [Rear]
(SBS-R)
The SBS-R is a system which is
designed to reduce damage in the
event of a collision by operating the
brake control (SBS brake) when the
system’s sensors detect an obstruction
at the rear of the vehicle while driving
at a speed of about 2 to 8 km/h (2 to
4 mph) and the system determines that
a collision is unavoidable.
WARNING
Do not rely completely on the SBS-R
system:
¾The
SBS-R system is only designed to
reduce damage in the event of a
collision. Over reliance on the system
leading to the accelerator pedal or
brake pedal being mistakenly
operated could result in an accident.
¾To assure the correct operation of
the
SBS-R, heed the following
cautions.
When Driving
i-ACTIVSENSE
*Some models.4-177

xThe SBS-R system will operate under
the following conditions.
xThe engine is running.xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is between
about 2 to 8 km/h (2 to 4 mph).
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions and the
SBS-R may not operate.
xThe height of the obstruction is
low such as low walls or trucks
with low loading platforms.
xThe height of the obstruction is
high such as trucks with high
loading platforms.
xThe obstruction is small.xThe obstruction is thin such as a
signpost.
xThe surface of the obstruction is
not pointed vertically relative to
the vehicle.
xThe obstruction is soft such as a
hanging curtain or snow stuck to a
vehicle.
xThe obstruction is shaped
irregularly.
xThe obstruction is extremely close.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions correctly
and the
SBS-R may not operate.
xSomething is stuck on the bumper
near a rear ultrasonic sensor.
xThe brake or accelerator pedal is
operated.
xThere is another obstruction near
one obstruction.
xDuring inclement weather such as
rain, fog and snow.
xHigh or low humidity.xHigh or low temperaturesxStrong winds.xThe path of travel is not flat.xHeavy luggage is loaded in the
luggage compartment or on the
rear seat.
xObjects such as a wireless aerial,
fog light, or illuminated number
plate is installed near a rear
ultrasonic sensor.
xThe orientation of a rear ultrasonic
sensor has deviated for reasons
such as a collision.
xThe vehicle is affected by other
sound waves such as the horn,
engine noise, ultrasonic sensor of
another vehicle.
xIn the following cases, a rear
ultrasonic sensor and rear camera
may detect something as a target
obstruction which could cause the
SBS-R system to operate.
xDriving on a steep slope.xWheel blocks.xHanging curtains, gate poles such
as at toll gates and railroad
crossing.
xWhen travelling near objects such
as foliage, barriers, vehicles, walls,
and fences along a road.
xWhen driving off-road in areas
where there is grass and forage.
xWhen passing through low gates,
narrow gates, car washing
machines, and tunnels.
xA trailer is connected.xA bright light source such as
sunlight hits the rear camera.
xThe surroundings are dark.
When Driving
i-ACTIVSENSE
4-179

xAn exterior accessory such as a
bicycle carrier is installed around a
rear ultrasonic sensor.
x(Manual transmission)
If the vehicle is stopped by the SBS-R
operation and the clutch pedal is not
depressed, the engine stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-R brake
is operating.
xIf the vehicle is stopped by the SBS-R
operation and the brake pedal is not
depressed, displaying in meter
“Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the SBS-R
brake is automatically released.
xIf a Mazda genuine trailer hitch is
used, the SBS-R is automatically
turned off.
xTurn off the SBS-R system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear] (SBS-R) System Operation
The SBS-R can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-R is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-R is cancelled, the
SBS-R is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-R is cancelled, the
Smart Brake Support [Rear Crossing]
(SBS-RC) is also cancelled.
When Driving
i-ACTIVSENSE
4-180

¾If cracks or damage caused by flying
gravel or debris is visible around a
rear radar and rear camera, stop
using the SBS-RC system
immediately and have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer). If the vehicle continues to
be driven with cracks or scratch
marks left around an ultrasonic
sensor, the system may operate
unnecessarily and cause an
unexpected accident.
Refer to Stopping the Smart Brake
Support [Rear Crossing] (SBS-RC)
System Operation on page 4-184.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for rear bumper
replacement.
Do not modify the suspension:
If the vehicle height or inclination is
changed, the
SBS-RC system may not
operate correctly because it cannot
detect obstructions correctly.
Do not apply a strong force to a rear
radar and rear camera:
When washing the vehicle, do not
spray highly pressurised water against a
rear radar and rear camera, or rub it
strongly. In addition, do not hit the rear
bumper forcefully when loading and
unloading cargo. Otherwise, the
sensors may not detect obstructions
correctly which could cause the
SBS-RC system to not operate
normally, or it could operate
unnecessarily.
NOTE
xThe SBS-RC system will operate
under the following conditions.
xThe engine is running.
xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is under about
10 km/h (6 mph).
xThe vehicle speed of an
approaching vehicle is about 3
km/h (2 mph) or faster.
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the SBS-RC system.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
xDriving on snow-covered roads for
long periods.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for long periods on
slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
When Driving
i-ACTIVSENSE
4-182

xThe rear side radar sensor
detection area is obstructed by a
nearby wall or parked vehicle.
(Reverse the vehicle to a position
where the radar sensor detection
area is no longer obstructed.)
1. Your vehicle

xA vehicle is approaching directly
from the rear of your vehicle.
1. Your vehicle

xThe vehicle is parked on a slant.
1. Your vehicle

xA vehicle is approaching from the
opposite direction on a steep
gradient.
1. Your vehicle

xDirectly after the SBS-RC system
becomes operable using the
personalisation feature.
xRadio wave interference from a
radar sensor equipped on a nearby
parked vehicle.
xTurn off the SBS-RC system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle. Otherwise,
the radio waves emitted by the radar
will be blocked causing the system to
not operate normally.
xIn the following cases, a rear radar
and rear camera may detect
something as a target obstruction
which could cause the SBS-RC
system to operate.
xHanging curtains, gate poles such
as at toll gates and railroad
crossing.
xWhen travelling near objects such
as foliage, barriers, vehicles, walls,
and fences along a road.
xWhen driving off-road in areas
where there is grass and forage.
xWhen passing through low gates,
narrow gates, car washing
machines, and tunnels.
xA trailer is connected.xA bright light source such as
sunlight hits the rear camera.
xThe surroundings are dark.
When Driving
i-ACTIVSENSE
4-183

x(Manual transmission)
If the vehicle is stopped by the
SBS-RC operation and the clutch
pedal is not depressed, the engine
stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-RC
brake is operating.
xIf the vehicle is stopped by the
SBS-RC operation and the brake
pedal is not depressed, displaying in
meter “Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the
SBS-RC brake is automatically
released.
xIf a Mazda genuine trailer hitch is
used, the SBS-RC is automatically
turned off.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear Crossing]
(SBS-RC) System
Operation
The SBS-RC can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-RC is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-RC is cancelled, the
SBS-RC is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-RC is cancelled, the
Smart Brake Support [Rear] (SBS-R)
is also cancelled.
When Driving
i-ACTIVSENSE
4-184

The Rear Cross Traffic Alert (RCTA)
uses rear side radar sensor to detect
vehicles approaching from the rear
left and right sides of the vehicle,
and it assists the driver in checking
the rear of the vehicle while reversing
by flashing the Blind Spot Monitoring
(BSM) warning lights and activating
the warning sound.
Refer to Rear Cross Traffic Alert
(RCTA) on page 4-126.
360°View Monitor Range
1. Cameras
2. Ultrasonic sensors
3. Front/Rear side radar sensors
WARNING
Always confirm the safety of the area
around the vehicle with the mirrors
and directly with your eyes when
driving:
The 360°View Monitor is an auxiliary
device which assists the driver in
checking the safety of the area around
the vehicle.
The shooting range of the cameras and
detection range of the sensors are
limited. For example, the areas in black
at the front and rear of the vehicle
image and the seams where each of
the camera images merge are blind
spots where an obstruction may not be
visible. In addition, the extended
vehicle width lines and projected
vehicle path lines are only to be used
as references, and the images on the
screen may differ from the actual
conditions.
CAUTION
¾Do not use the 360°View Monitor
under any of the following
conditions.
¾Icy or snow-covered roads.
¾Tyre chains or a temporary spare
tyre is installed.
¾The front or rear doors are not fully
closed.
¾The vehicle is on a road incline.
¾The door mirrors are retracted.
¾Do not hit the front/rear camera,
front bumper, liftgate, and door
mirrors forcefully. The camera
position or installation angle may
shift.
¾The cameras are waterproof. Do not
disassemble, modify, or remove a
camera.
¾The camera cover is made of hard
plastic, therefore do not apply oil
film remover, organic solvents, wax,
or coating agents. If any such agent
gets on the camera cover, wipe it off
using a soft cloth immediately.
¾Do not rub the camera lens
forcefully, or clean it with an abrasive
or hard brush. Otherwise, it could
scratch the camera lens and
negatively affect the images.
When Driving
i-ACTIVSENSE
4-186

xExtremely bright light such as
sunlight or headlights hitting the
camera lens directly.
xThe surroundings are illuminated
by vehicle lights, fluorescent lights,
or LED lights (display may flicker).
xExtremely small dark or white dots
appear on the screen (dots may
flicker).
xBecause the 360°View Monitor
camera uses a special lens, the
distance displayed on the screen
differs from the actual distance.
xObstructions displayed on the screen
may appear differently than in
actuality. (Obstructions may appear
fallen, larger, or longer than they
actually are.)
xDo not apply stickers to a camera or
the area around it. In addition, do
not install accessories or an
illuminated number/character
number plate to the area around a
camera. Otherwise, the camera may
not correctly display the surrounding
conditions.
xFree/open source software
information
This product includes free/open
sources. Information about the
licensing and source code is available
at the following URL.
https://www.denso.com/
global/en/opensource/svss/
mazda/
When Driving
i-ACTIVSENSE
4-188

Forward Sensing Camera
(FSC)
*
▼Forward Sensing Camera (FSC)
Your vehicle is equipped with a
Forward Sensing Camera (FSC). The
Forward Sensing Camera (FSC) is
positioned near the rearview mirror
and used by the following systems.
xHigh Beam Control System (HBC)xAdaptive LED Headlights (ALH)xLane Departure Warning System
(LDWS)
xTraffic Sign Recognition System (TSR)xDistance & Speed Alert (DSA)xDriver Attention Alert (DAA)xMazda Radar Cruise Control
(MRCC)
xMazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)
xLane-keep Assist System (LAS)xCruising & Traffic Support (CTS)xSmart Brake Support (SBS)
1. Forward Sensing Camera (FSC)

The Forward Sensing Camera (FSC)
determines the conditions ahead of
the vehicle while travelling at night and
detects traffic lanes. The distance in
which the Forward Sensing Camera
(FSC) can detect objects varies
depending on the surrounding
conditions.
WARNING
Do not modify the suspension:
If the vehicle height or inclination is
changed, the system will not be able to
correctly detect vehicles ahead. This
will result in the system not operating
normally or mistakenly operating,
which could cause a serious accident.
CAUTION
¾Do not apply accessories, stickers or
film to the windscreen near the
Forward Sensing Camera (FSC).
If the area in front of the Forward
Sensing Camera (FSC) lens is
obstructed, it will cause the system
to not operate correctly.
Consequently, each system may not
operate normally which could lead
to an unexpected accident.
¾Do not disassemble or modify the
Forward Sensing Camera (FSC).
Disassembly or
modification of the
Forward Sensing Camera (FSC) will
cause a malfunction or mistaken
operation. Consequently, each
system may not operate normally
which could lead to an unexpected
accident.
¾Heed the following cautions to
assure the correct operation of the
Forward Sensing Camera (FSC).
¾Be careful not to scratch the
Forward Sensing Camera (FSC)
lens or allow it to get dirty.
¾Do not remove the Forward
Sensing Camera (FSC) cover.
¾Do not place objects on the
instrument panel which reflect
light.
When Driving
i-ACTIVSENSE
4-216*Some models.

¾Always keep the windscreen glass
around the camera clean by
removing dirt or fogging. Use the
windscreen defroster to remove
fogging on the windscreen.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning the
interior side of the windscreen
around the Forward Sensing
Camera (FSC).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) before performing
repairs around the Forward Sensing
Camera (FSC).
¾The Forward Sensing Camera (FSC)
is installed to the windscreen.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for windscreen repair
and replacement.
¾When cleaning the windscreen, do
not allow glass cleaners or similar
cleaning fluids to get on the
Forward Sensing Camera (FSC)
lens. In addition, do not touch the
Forward Sensing Camera (FSC)
lens.
¾When performing repairs around
the rearview mirror, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning of the
camera lens.¾Do not hit or apply strong force to
the Forward Sensing Camera (FSC)
or the area around it. If the
Forward Sensing Camera (FSC) is
severely hit or if there are cracks or
damage caused by flying gravel or
debris in the area around it, stop
using the following systems and
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
¾High Beam Control System
(HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System
(LDWS)
¾Traffic Sign Recognition System
(TSR)
¾Distance & Speed Alert (DSA)
¾Driver Attention Alert (DAA)
¾Mazda Radar Cruise Control
(MRCC)
¾Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function)
¾Lane-keep Assist System (LAS)
¾Cruising & Traffic Support (CTS)
¾Smart Brake Support (SBS)
¾The direction in which the Forward
Sensing Camera (FSC) is pointed
has been finely adjusted. Do not
change the installation position of
the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could
result in damage or malfunction.
¾Always use tyres for all wheels that
are of the specified size, and the
same manufacturer, brand, and tread
pattern. In addition, do not use tyres
with significantly different wear
patterns on the same vehicle as the
system may not operate normally.
When Driving
i-ACTIVSENSE
4-217