light MAZDA MODEL CX-30 2019 Owners Manual (in English)

¾The Forward Sensing Camera (FSC)
includes a function for detecting a
soiled windscreen and informing the
driver, however, depending on the
conditions, it may not detect plastic
shopping bags, ice or snow on the
windscreen. In such cases, the
system cannot accurately determine
a vehicle ahead and may not be able
to operate normally. Always drive
carefully and pay attention to the
road ahead.
NOTE
xIn the following cases, the Forward
Sensing Camera (FSC) cannot detect
target objects correctly, and each
system may be unable to operate
normally.
xThe height of the vehicle ahead is
low.
xYou drive your vehicle at the same
speed as the vehicle ahead.
xHeadlights are not turned on
during the night or when going
through a tunnel.
xIn the following cases, the Forward
Sensing Camera (FSC) may not be
able to detect target objects
correctly.
xUnder bad weather condition,
such as rain, fog and snow.
xThe window washer is being used
or the windscreen wipers are not
used when it's raining.
xIce, fog, snow, frost, rainfall, dirt,
or foreign matter such as a plastic
bag is stuck on the windscreen.
xTrucks with low loading platforms
and vehicles with an extremely low
or high profile.
xWhen driving next to walls with no
patterning (including fences and
longitudinally striped walls).
xThe tail lights of the vehicle ahead
are turned off.
xA vehicle is outside the
illumination range of the
headlights.
xThe vehicle is making a sharp turn,
or ascending or descending a steep
slope.
xEntering or exiting a tunnel.xHeavy luggage is loaded causing
the vehicle to tilt.
xStrong light is shone at the front of
the vehicle (back light or
high-beam light from on-coming
vehicles).
xThere are many light emitters on
the vehicle ahead.
xWhen the vehicle ahead is not
equipped with tail lights or the tail
lights are turned off at nighttime.
xElongated luggage or cargo is
loaded onto installed roof rails and
covers the Forward Sensing
Camera (FSC).
xExhaust gas from the vehicle in
front, sand, snow, and water
vapour rising from manholes and
grating , and water splashed into
the air.
xWhen towing a malfunctioning
vehicle.
xThe vehicle is driven with tyres
having significantly different wear.
xThe vehicle is driven on down
slopes or bumpy roads.
xThere are water puddles on the
road.
xThe surroundings are dark such as
during the night, early evening, or
early morning , or in a tunnel or
indoor parking lot.
xThe illumination brightness of the
headlights is reduced or the
headlight illumination is weakened
due to dirt or a deviated optical
axis.
When Driving
i-ACTIVSENSE
4-218

xThe target object enters the blind
spot of the Forward Sensing
Camera (FSC).
xA person or object bursts onto the
road from the shoulder or cuts
right in front of you.
xYou change lanes and approach a
vehicle ahead.
xWhen driving extremely close to
the target object.
xTyre chains or a temporary spare
tyre is installed.
xThe vehicle ahead has a special
shape. For example, a vehicle
towing a trailer house or a boat, or
a vehicle carrier carrying a vehicle
with its front pointed rearward.
xIf the Forward Sensing Camera (FSC)
cannot operate normally due to rain,
backlight, or fog , the system
functions related to the Forward
Sensing Camera (FSC) are
temporarily stopped and the
following warning lights turn on.
However, this does not indicate a
malfunction.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf the Forward Sensing Camera (FSC)
cannot operate normally due to high
temperatures, the system functions
related to the Forward Sensing
Camera (FSC) are temporarily
stopped and the following warning
lights turn on. However, this does
not indicate a malfunction. Cool
down the area around the Forward
Sensing Camera (FSC) such as by
turning on the air conditioner.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf the Forward Sensing Camera (FSC)
detects that the windscreen is dirty
or foggy, the system functions related
to the Forward Sensing Camera
(FSC) are temporarily stopped and
the following warning lights turn on.
However, this does not indicate a
problem. Remove the dirt from the
windscreen or press the defroster
switch and defog the windscreen.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf there are recognizable cracks or
damage caused by
flying gravel or
debris on the windscreen, always
have the windscreen replaced.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for replacement.
xThe Forward Sensing Camera (FSC)
recognises pedestrians when all of
the following conditions are met:
xThe height of a pedestrian is about
1 to 2 meters.
xAn outline such as the head, both
shoulders, or the legs can be
determined.
xIn the following cases, the Forward
Sensing Camera (FSC) may not be
able to detect target objects
correctly:
When Driving
i-ACTIVSENSE
4-219

Front Camera/Side
Cameras/Rear Camera
*
▼Front Camera/Side Cameras/Rear
Camera
Your vehicle is equipped with a front
camera, side cameras, and a rear
camera. The 360°View Monitor uses
each camera.
Refer to 360°View Monitor on page
4-185.
The front camera, side cameras, and
rear camera shoot images of the area
surrounding the vehicle.
Each camera is installed to the
following positions.
1. Side cameras
2. Front camera
3. Rear camera
Driver Monitoring
Camera
*
▼Driver Monitoring Camera
The driver monitoring camera detects
changes in the driver's facial features
and estimates the amount of
accumulated fatigue and sleepiness of
the driver.
1. Driver monitoring camera
NOTE
xDriver Monitoring (DM) and the
earlier collision warning may not
operate normally under the following
conditions.
xThe driver monitoring camera is
covered with something.
xYou are driving the vehicle while
leaning on the steering wheel.
xYou are wearing glasses or
sunglasses.
xA cap or hat you are wearing
partially blocks the driver
monitoring camera's view of your
eyes, you have long bangs partially
covering your eyes, or a part of
your face is invisible due to a face
mask.
xThe lighting conditions change
significantly (such as backlight,
light from the side, or direct light
from the setting sun, and the
headlights of on-coming vehicles).
When Driving
i-ACTIVSENSE
4-226*Some models.

30 km/h (19 mph) or more and press
the RES switch.
▼To Te m p o ra r i l y C a n c e l
To temporarily cancel the system, use
one of these methods:
xSlightly depress the brake pedal.xPress the CANCEL switch.x(Manual transmission)
Depress the clutch pedal.
If the RES switch is pressed when the
vehicle speed is 30 km/h (19 mph) or
higher, the system reverts to the
previously set speed.
NOTE
xIf any of the following conditions
occur, the cruise control system is
temporarily cancelled.
xEven when the brake pedal is
slightly depressed.
xThe DSC is operating.xThere is a problem in the system.xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xWhen the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
x(Automatic transmission)
The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from D
to M position). Therefore, engine
braking will not be applied even if
the transmission is shifted down to a
lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
▼To D e a c t i va t e
Press the cruise switch again.
When Driving
Cruise Control
4-231

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Please note that the TPMS is not a
substitute for proper tyre
maintenance, and it is the driver's
responsibility to maintain correct tyre
pressure, even if under-inflation has
not reached the level to trigger
illumination of the TPMS low tyre
pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not
operating properly.
The TPMS malfunction indicator is
combined with the low tyre pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then
remain continuously illuminated.
This sequence will continue upon
subsequent vehicle start-ups as long
as the malfunction exists. When the
malfunction indicator is illuminated,
the system may not be able to detect
or signal low tyre pressure as
intended. TPMS malfunctions may
occur for a variety of reasons,
including the installation of
replacement or alternate tyres or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tyres or wheels on your vehicle to
ensure that the replacement or
alternate tyres and wheels allow the
TPMS to continue to function
properly.
¾To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tyre deflation or blow out.▼If there is a problem with the Tyre
Pressure Monitoring System
(TPMS)
If the TPMS warning light flashes, there
may be a problem with the system.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the system inspected.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Flashing) on page
7-57.
In the following cases, the system
cannot recognise the tyre pressures
correctly and the TPMS warning light
may flash.
xThere is equipment or a device
nearby emitting radio signals the
same as a tyre pressure sensor.
xA metallic object such as a
non-genuine electronic device is
installed near the centre of the
instrument panel (obstructs the radio
signals from the tyre pressure sensors
to the receiver).
xA device such as one of the following
is used in the cabin.
xElectronic devices such as a
computer.
xConverter devices such as a
DC-AC converter.
xThere is a large accumulation of
snow or ice around the vehicle tyres.
xThe battery in a tyre pressure sensor
is dead.
xA wheel not equipped with a tyre
pressure sensor is used.
xTyres employing steel in the sidewall
of the tyre are installed.
xTyre chains are used.
▼When a tyre pressure decreases
If the TPMS warning light turns on, a
tyre pressure may be low. Inspect the
When Driving
Tyre Pressure Monitoring System (TPMS)
4-233

tyre pressures and adjust them to the
correct inflation pressure.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Turns on) on page
7-60.
▼Tyres and Wheels
CAUTION
When inspecting/adjusting the tyre
pressures, do not apply excessive force
to the air valve of the tyre pressure
sensor. Otherwise, the tyre pressure
sensor could be damaged.
When changing tyres and wheels
When changing the tyres or wheels
(such as installing winter tyres), it will
be necessary to register the ID signal
code of the tyre pressure sensor to the
TPMS.
Have an expert repairer (we
recommend an Authorised Mazda
Repairer) do the registration or register
the ID signal codes of the tyre pressure
sensors using the following procedure.
NOTE
The tyre pressure sensors on each
wheel have a unique ID signal code.
For the TPMS to operate correctly, the
ID signal codes of the tyre pressure
sensors need to be registered to the
system.
1. Wait more than 19 minutes after
changing a tyre or wheel.
2. After more than 19 minutes have
passed, drive the vehicle at a speed
of about 25 km/h (16 mph) or
faster for 3 minutes or longer. While
driving, the ID signal codes of the
tyre pressure sensors are
automatically registered.
NOTE
If you drive the vehicle within 19
minutes of changing a tyre or wheel,
the TPMS warning light will flash
because the ID signal codes for the
tyre pressure sensors were not
registered. In this case, stop the vehicle
and register the ID signal codes of the
tyre pressure sensors following the
procedure.
When replacing tyres and wheels
CAUTION
¾When replacing the tyres and
wheels, consult an expert repairer
(we recommend an Authorised
Mazda Repairer) Otherwise, the tyre
pressure sensors could be damaged
when replacing them.
¾Do not install non-genuine wheels. If
wheels other than genuine ones are
installed, it may not be possible to
install the tyre pressure sensors.
When replacing a tyre or wheel, always
install the tyre pressure sensor. The
following combinations of tyres,
wheels, or tyres and wheels are
possible.
xThe tyre pressure sensor from the old
wheel is removed and it is installed
to the new wheel.
xOnly a tyre is replaced without
replacing the tyre pressure sensor
and wheel.
xA new tyre pressure sensor is
installed to a new wheel.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-234

Petrol Particulate Filter
(SKYACTIV-X 2.0)
▼Petrol Particulate Filter
The petrol particulate filter collects and
removes most of the particulate matter
(PM) in the exhaust gas of a petrol
engine.
PM collected by the petrol particulate
filter is cleared during normal driving ,
however, PM may not be removed and
the petrol particulate filter warning
indication/warning light may
illuminate under the following
conditions:
xIf the vehicle is driven at 20 km/h
(12 mph) or less continuously.
xIf the vehicle is repeatedly driven for
a short period of time (30 minute or
less) or driven while the engine is
cold.
xIf the vehicle is idled for a long time.
Refer to Petrol Particulate Filter
Warning Indication/Warning Light on
page 7-54.
When Driving
Petrol Particulate Filter
4-236

Diesel Particulate Filter
(SKYACTIV-D 1.8)
▼Diesel Particulate Filter
The diesel particulate filter collects and
removes most of the particulate matter
(PM) in the exhaust gas of a diesel
engine.
PM collected by the diesel particulate
filter is cleared during normal driving ,
however, PM may not be removed and
the diesel particulate filter warning
indication/warning light may
illuminate under the following
conditions:
xIf the vehicle is driven at 15 km/h (9
mph) or less continuously.
xIf the vehicle is repeatedly driven for
a short period of time (10 minute or
less) or driven while the engine is
cold.
xIf the vehicle is idled for a long time.
Refer to Diesel Particulate Filter on
page 7-54.
When Driving
Diesel Particulate Filter
4-237

xWhen the temperature around the lens is high/low.xWhen the camera is wet such as on a rainy day or during periods of high
humidity.
xWhen foreign material such as mud is stuck around the camera.xWhen the camera lens reflects sunlight or headlight beams.xThe surroundings are illuminated by vehicle lights, fluorescent lights, or LED
lights (display may flicker).
xExtremely small dark or white dots appear on the screen (dots may flicker).xImage display may be delayed if the temperature around the camera is low.
▼Viewing the Display
Predicted vehicle path assist lines display type
The projected path guidance mode displays the predicted path of the vehicle after
you turn the steering wheel.
Use this mode for parking your vehicle in a parking space or garage.
a) Projected vehicle path (yellow)
These lines are displayed as a reference for the projected path of the vehicle.
The lines displaying the projected vehicle path change after you turn the steering
wheel.
b) Extended vehicle width lines (blue)
These lines indicate the vehicle's extended width.
These lines are not displayed when the vehicle's wheels are in the straight-ahead
position.
c) Distance guide lines (red)
These lines indicate the approximate distance to a point measured from the
vehicle's rear (from the end of the bumper).
The blue line indicates the point about 50 cm (19 in) from the rear bumper.
The red and yellow lines, which change position after you turn the steering wheel,
indicate the points about 50 cm (19 in) for the red line and 100 cm (39.3 in) for
the yellow lines from the rear bumper (at the centre point of each of the lines).
A degree of error occurs when the wheels are not in the straight-ahead position.
In the above illustration, the right side of the vehicle is in a position closer to the
actual distance displayed by the distance guide lines (red: about 50 cm (19 in)
When Driving
Rear View Monitor
4-241