light MAZDA MODEL CX-30 2019 Owners Manual (in English)

Light Bulbs
▼Light Bulbs
Front
Ty p e A
1. Vanity mirror lights*
2. Front overhead lights/Front map
lights
3. Side direction indicator lights
4. Front direction indicator lights/
Position lights
5. Running lights/Headlights (Low
beam)
6. Headlights (High/Low beam)
7. Running lights
8. Headlights (High beam)
*
9. Headlights (Wide-range low beam)*
Ty p e B
1. Vanity mirror lights*
2. Front overhead lights/Front map
lights
3. Side direction indicator lights
4. Running lights
*
5. Front direction indicator lights/
Position lights
6. Headlights (High/Low beam)
Rear
1. Luggage compartment light
2. High-mount brake light
3. Rear overhead light
4. Tail lights
*
5. Rear direction indicator lights
6. Brake lights/Tail lights
7. Tail lights (Liftgate side)
*
8. Reverse lights
9. Rear fog light*
10.Number plate lights
CAUTION
When removing the lens or lamp unit
using a flathead screwdriver, make sure
that the flathead screwdriver does not
contact the interior terminal. If the
flathead screwdriver contacts the
terminal, a short circuit may occur.
NOTE
xWhen replacing a bulb, contact an
expert repairer (we recommend an
Authorised Mazda Repairer) if
necessary.
xUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
xFor details regarding the installation
positions of the interior lights, refer
to the following:
Maintenance and Care
Owner Maintenance
6-44*Some models.

xVanity mirror lights
Refer to Vanity Mirrors on page
5-32.
xFront overhead lights/front map
lights, rear overhead light, and
luggage compartment light
Refer to Interior Lights on page
5-33.
▼Replacing Exterior Light Bulbs
The exterior lights have either LEDs or
normal bulbs.
Only the bulb for a running lights (type
B) can be replaced.
LED type
xHeadlightsxRunning lights (Type A)xPosition lightsxFront direction indicator lightsxSide direction indicator lightsxHigh-mount brake lightxRear direction indicator lightsxBrake lightsxTail lightsxReverse lightsxRear fog lightsxNumber plate lights
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an expert
repairer (we recommend an
Authorised Mazda Repairer) if the
replacement is necessary.
Bulb type
Running lights (Type B)
1. Make sure the ignition is switched
off, and the headlight switch is off.
2. If you are changing the left bulb,
start the engine, turn the steering
wheel all the way to the right, and
turn off engine. If you are changing
the right bulb, turn the steering
wheel to the left.
3. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
4. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
5. Turn the screw anticlockwise and
remove it, and then partially peel
back the mudguard.
Maintenance and Care
Owner Maintenance
6-45

6. Remove the wiring harness from
the clip.
7. Turn the socket and bulb assembly
anticlockwise and remove it.
8. Disconnect the bulb from the
socket.
9. Install the new bulb in the reverse
order of the removal procedure.
▼Replacing Interior Light Bulbs
LED type
xFront overhead lights/Front map
lights
xRear overhead lightxVanity mirror lights*
xLuggage compartment light
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an expert
repairer (we recommend an
Authorised Mazda Repairer) if the
replacement is necessary.
Fuses
▼Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate
circuit protector. If a fuse has blown,
the inside element will be melted.

If the same fuse blows again, avoid
using that system and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
▼Fuse Replacement
Replacing the fuses on the vehicle's
left side
If the electrical system does not work,
first inspect the fuses on the vehicle's
left side.

1. Make sure the ignition is switched
off, and other switches are off.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the
fuse puller provided on the fuse
Maintenance and Care
Owner Maintenance
6-46*Some models.

block located in the engine
compartment.
4. Inspect the fuse and replace it if it is
blown.
1. Normal
2. Blown

5. Insert a new fuse of the same
amperage rating , and make sure it
fits tightly. If it does not
fit tightly,
have an expert install it. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
If you have no spare fuses, borrow
one of the same rating from a
circuit not essential to vehicle
operation, such as the audio or
accessory socket circuit.
CAUTION
Always replace a fuse with a
genuine Mazda fuse or equivalent
of the same rating. Otherwise, you
may damage the electric system.
6. Reinstall the cover and make sure
that it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the
fuse block under the bonnet.
If a fuse is blown, it must be replaced.
Follow these steps:

1. Make sure the ignition is switched
off, and other switches are
off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of
the same amperage rating.
1. Normal
2. Blown

Maintenance and Care
Owner Maintenance
6-47

No.FUSE RAT-
INGPROTECTED COMPONENT
F715 A
Fuel warmer
*
20 A
Fuel pump*
F8 15 A Engine control system
F9 15 A
Transmission control system
*
F10 15 A Engine control system
F11 7.5 A Air conditioner
F12 15 A Engine control system
F13 15 A
NOx sensor
*
F14 20 A
Front seat warmer*
F15 20 A
Headlight washer*
F16 15 A For protection of various circuits
F17ŠŠ
F18 15 A Accessory sockets
F19 60 A Power steering system
F20 15 A Headlight (LH) 1
F21 15 A Headlight (RH) 1
F22 15 A Keyless system
F23 30 A ABS, Dynamic stability control system
F24 15 A Headlight (LH) 2
F25 15 A Headlight (RH) 2
F26 7.5 A On board diagnostics
F27 25 A For protection of various circuits
F28 25 A For protection of various circuits
F29 15 A Windscreen washer
F30ŠŠ
F31 15 A Horn
F32 15 A Headlights
F33ŠŠ
F34ŠŠ
F35 50A ABS, Dynamic stability control system
F36ŠŠ
F37 40 A Rear window defogger
F38 50 A For protection of various circuits
Maintenance and Care
Owner Maintenance
6-50*Some models.

No.FUSE RAT-
INGPROTECTED COMPONENT
F39ŠŠ
F40 40 A Air conditioner
F41ŠŠ
F42 20 A Windscreen wiper
F43 30 A
Cooling fan
*
F44 30 A Starter
F45 10 A Engine control system
F46 15 A Audio
F47 15 A For protection of various circuits
F48 7.5 A Air bag
F49 15 A Instrument cluster
F50 15 A Room light
F51 25 A Audio
F52 10 A
Sunroof
*
F53 15 A Engine control system
F54 15 A i-ACTIVSENSE
F55 50 A
For protection of various circuits
*
F56 50 AŠ
Maintenance and Care
Owner Maintenance
*Some models.6-51

No.FUSE RAT-
INGPROTECTED COMPONENT
F16 15 A Illumination
F17 10 A Brake lights
F18 10 A Reverse lights
F19 10 A Rear direction indicator lights
F20 10 A Tail lights
F21 10 A Tail lights
F22 7.5 A Electric steering lock
F23ŠŠ
Maintenance and Care
Owner Maintenance
6-53

with plain water is ineffective, use a
mild soap made for use on vehicles.

Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the finish.

After washing the vehicle, dry it with a
clean chamois to prevent water spots
from forming.
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
When using an automatic car wash
xRetract the door mirrors.xThe automatic car wash brushes
could reduce the paint lustre or
hasten paint deterioration.
When using a high water pressure car
wash
High water temperature and high
water pressure car washers are
available depending on the type of car
wash machine. If the car washer nozzle
is put too close to the vehicle, the
force of the spray could damage or
deform the molding,
affect the
sealability of parts, and allow water to
penetrate the interior. Keep a
sufficient
space (30 cm (12 in) or more)
between the nozzle and the vehicle. In
addition, do not spend too much time
spraying the same area of the vehicle,
and be very careful when spraying
between gaps in doors and around
windows.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the
finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle
body, wax the metal trim to maintain
its lustre.

1. Use wax which contains no
abrasives.
Waxes containing abrasive will
remove paint and could damage
bright metal parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colours.
3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle does not need it.
▼Paint Damage Touch-up
Repair damage to the finish caused by
stone chipping, damage during parking
etc., by using Mazda touch-up paint
before rust begins to form. First,
remove the dirt and grease with a
clean soft cloth.

If rust has already begun to form:

1. Remove rust completely with
sandpaper.
2. Wipe with a clean soft cloth.
3. Apply rust preventive primer to the
area.
Maintenance and Care
Appearance Care
6-57

▼Plastic Part Maintenance
xWhen cleaning the plastic lenses of
the lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these
chemical agents can discolour or
damage the surfaces resulting in a
significant loss in functionality. If
plastic parts become inadvertently
exposed to any of these chemical
agents, flush with water immediately.
xIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
petrol, oil, engine coolant, or battery
fluid, it could cause discolouration,
staining, or paint peeling. Wipe off
any such chemical agents or fluids
using a soft cloth immediately.
xHigh water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
xDo not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
xIn addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
xDo not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
xRubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following , wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or
peeling of the coating , and it will make
it hard to wipe off later.
xBeverage or fragrancexGrease or oilxSoiling
▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which
have been pulled out for cleaning,
dry them off thoroughly and make
Maintenance and Care
Appearance Care
6-59

sure there is no remaining moisture
on them.
WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
expert repairer (we recommend an
Authorised Mazda Repairer):
If a seat belt is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.
Use a mild detergent to remove
soiling from a seat belt:
If organic solvents are used for cleaning
the seat belts or they become stained
or bleached, there is the possibility of
them becoming weakened and as a
result, they may not function at their
full capacity which could cause serious
injury or death.
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will
make it difficult to clean them later,
and it may
affect the smooth retracting
of the seat belt.
▼Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
▼Upholstery Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe
off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼Leather Upholstery Maintenance*
1. Remove dust and sand using a
vacuum cleaner.
2. Wipe off the soiled area with a soft
cloth and a suitable, special cleaner
or a soft cloth soaked in a mild
detergent (about 5%) diluted with
water.
3. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
4. Remove moisture with a dry, soft
cloth and allow the leather to
further dry in a well-ventilated,
shaded area. If the leather gets wet
such as from rain, remove the
moisture and dry it as soon as
possible.
NOTE
xBecause genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
xTo maintain the quality for as long as
possible, periodical maintenance,
about twice a year, is recommended.
xIf the leather upholstery comes into
contact with any of the following,
clean it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
xSand or dirtxGrease or oil, such as hand creamxAlcohol, such as in cosmetic or
hair dressing items
xIf the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such
as hardening and shrinkage.
Maintenance and Care
Appearance Care
6-60*Some models.