light MAZDA MODEL CX-30 2019 Owners Manual (in English)

NOTE
xOnly make calls manually for conditions requiring urgent treatment such as illness
or serious injury.
xWhen making emergency calls manually, stop the vehicle in a safe location before
making the call.
xThe call centre will end an emergency call. The user cannot end the emergency
call.
xIf a call is disconnected or a call cannot be made to the call centre correctly, an
automatic call is made again to the call centre. To cancel the redialing, refer to
Manual emergency call cancellation.
1. Make sure that the ignition is switched ON.
2. Long-press the Emergency call switch on the overhead console and then release
your finger from the switch.
1. Emergency call switch
3. The indicator light (green) on the Emergency call switch flashes slowly (0.5
second intervals) and the call is made to the call centre.
1. Green
4. When the connection is established with the call centre, the indicator light
(green) flashes somewhat quickly (0.3 second intervals) and the beep sounds
simultaneously, and the transmission of the vehicle information begins.
5. When the transmission of the vehicle information is completed or about 20
seconds have elapsed since the transmission began, the beep sounds and the
voice call with the call centre starts.
If Trouble Arises
Mazda
ERA-GLONASS
7-18

6. If the connection fails, the indicator light (red) turns on and the indicator light
(green) flashes quickly (0.15 second intervals), and the beep sounds
simultaneously.
Make a manual emergency call again.
1. Red (Turns on)
2. Green (Flashes)
NOTE
If a call to the call centre does not connect even though the indicator light shows a
call is possible, make a call to the police or other authority by means other than the
Mazda
ERA-GLONASS.
Manual emergency call cancellation
A manual emergency call can be cancelled even after the Emergency call switch has
been pressed by pressing the switch again, as long as the call with the call centre has
not begun. If the call cannot be cancelled and the call with the call centre has
begun, tell the operator that the call is mistaken.
▼Indicator Light/Beep Sound
The indicator light turns on/flashes and beep sounds are activated to notify the
driver of the system operation status or if there is a problem with the system.
StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Diagnosis Turns on Turns onŠŠWhen the ignition is switched
ON, it turns on and then
turns off after a few seconds.
NOTE
A manual emergency call is
not possible during diagnosis.
Normal Turns off Turns offŠŠThe system is operating nor-
mally.
If Trouble Arises
Mazda
ERA-GLONASS
7-19

StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Malfunction Turns off Turns onŠ3 beeps
(Slow intermit-
tent sound)
xA system malfunction is
detected.
xThe remaining power of
the built-in battery is low.
CAUTION
If the indicator light (red) re-
mains on constantly, the sys-
tem will not operate normal-
ly. Have the vehicle inspected
at an expert repairer (we rec-
ommend an Authorised Maz-
da Repairer) as soon as possi-
ble.
Call being
made with call
centreFlashes Turns offSlow
(0.5 second
intervals)The beep does
not sound, but
the ringback
tone can be
heard.An emergency call is being
made by the Mazda
ERA-GLONASS.
Vehicle infor-
mation is be-
ing transmittedFlashes Turns
offSomewhat
quick
(0.3 second
intervals)Continuous in-
termittent
soundVehicle information is being
transmitted to the call centre.
Start of voice
callTu r n s o n Tu r n s o ffŠ1 beep
During a voice call with the
call centre.
During voice
callTu r n s o n Tu r n s
offŠŠ
Connection
failureFlashes Turns onQuick
(0.15 second
intervals)3 beeps
(Fast intermit-
tent sound)When an emergency call fails
to connect.
▼Te s t M o d e
The test mode function makes sure that the Mazda ERA-GLONASS can operate
normally.
Have your vehicle tested at an Authorised Mazda Repairer when performing the test
mode.
Method to start test mode
Switch the ignition ON while the parking brake is applied, and wait 2 minutes with
the vehicle stopped.
If Trouble Arises
Mazda
ERA-GLONASS
7-20

After that, perform the following procedure.
Move the signal lever up to right
turn
Move the signal lever up to right
turnMove the signal lever
down to left turn
Move the signal lever down
to left turn Return the signal lever to offReturn the signal lever to
Return the signal lever to off
Return the signal lever to off Return the signal lever to off Move the signal lever up to right
turnWithin 5 seconds
Within 1 second Within 1 second Within 1 second Within 1 second
Within 1 second
Within 1 second
Within 1 second
Within 1 second Within 5 seconds
Within 5 seconds
Within 1 second Turn on the hazard warning
lights.
Turn off the hazard warning
lights.
Both red and green
Emergency call switch
indicator lights turn on.
Press the Emergency call
switch for one second or
longer and release it.
After the procedure is completed, the test mode is performed in the following order
automatically.
1. Procedure is completed
2. Switch to test mode
If Trouble Arises
Mazda
ERA-GLONASS
7-21

Parking in an Emergency
▼Parking in an Emergency
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.

The hazard warning lights warn other
drivers that your vehicle is a traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the direction indicators will
flash. The hazard warning indicator
lights in the instrument cluster flash
simultaneously.
NOTE
xThe direction indicators do not work
when the hazard warning lights are
on.
xCheck local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
▼Roadside Emergency Triangle
Retaining Strap
Keep the roadside emergency triangle
in the right side trim and secure it with
the strap.
1. Strap
If Trouble Arises
Parking in an Emergency
*Some models.7-23

Ty p e E
1. Jack lever
2. Spare tyre hold-down bolt
3. Screwdriver
*
4. Towing eyelet
5. Jack
6. Spare tyre
7. Wrench
*
8. Wheel brace
▼Jack*
To remove the jack
1. Remove the luggage mat.

2. Remove the jack.

To secure the jack
Perform the removal procedure in
reverse.
Maintenance
xAlways keep the jack clean.xMake sure the moving parts are kept
free from dirt or rust.
xMake sure the screw thread is
adequately lubricated.
▼Spare Tyre*
Your Mazda has a temporary spare
tyre.
The temporary spare tyre is lighter and
smaller than a conventional tyre, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tyres should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare
tyre on the front wheels (driving
wheels):
Driving with the temporary spare tyre
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tyre to the front wheel and install the
temporary spare tyre to the rear.
CAUTION
¾When using the temporary spare
tyre, driving stability may decrease
compared to when using only the
conventional tyre. Drive carefully.
¾To avoid damage to the temporary
spare tyre or to the vehicle, observe
the following precautions:
If Trouble Arises
Flat Tyre
*Some models.7-25

Emergency Flat Tyre
Repair Kit
*
▼Emergency Flat Tyre Repair Kit
The emergency flat tyre repair kit
included with your Mazda is for a
temporary repair of a slightly damaged
flat tyre resulting from running over
nails or similar sharp objects on the
road surface.
Perform the emergency
flat tyre repair
without removing the nail or similar
sharp object which punctured the tyre.
NOTE
Your vehicle is not equipped with a
spare tyre. In the event of a flat tyre,
use the emergency flat tyre repair kit to
repair the tyre temporarily. When
doing the repair, refer to the
instructions included in the emergency
flat tyre repair kit. If an emergency
repair was performed on a flat tyre
using the emergency flat tyre repair kit,
have an , repair or replace the tyre as
soon as possible.
▼About the Emergency Flat Tyre
Repair Kit
The emergency flat tyre repair kit
includes the following items.

1. Tyre sealant
2. Injection hose
3. Compressor
4. Spare valve core
5. Valve core tool
6. Instructions
7. Speed restriction sticker
WARNING
Do not allow children to touch the
tyre sealant:
¾Ingestion of tyre sealant is
dangerous. In the event tyre sealant
is accidentally swallowed, drink large
amounts of water immediately and
seek medical assistance.
If Trouble Arises
Flat Tyre
*Some models.7-27

xIf the tyre does not inflate, repair
of the tyre may not be possible. If
the tyre does not reach the
correct inflation pressure within a
10-minute period, it probably has
received more extensive damage.
When this happens, the
emergency flat tyre repair kit
cannot be used to repair the tyre.
Contact an expert repairer (we
recommend an Authorised
Mazda Repairer).
xIf the tyre has been over-inflated,
loosen the screw cap on the
compressor and bleed some of
the air out.
16.When the tyre has been inflated to
the proper inflation pressure, turn
the compressor switch off and
remove the compressor hose from
the tyre valve.
17.Install the tyre valve cap.
18.Put the emergency flat tyre repair
kit in the luggage compartment and
continue driving.
CAUTION
¾Drive carefully to an expert
repairer (we recommend an
Authorised Mazda Repairer) and
keep the vehicle speed below 80
km/h (50 mph).
¾If the vehicle is driven 80 km/h
(50 mph) or higher, the vehicle
might begin to vibrate.
NOTE
If the tyre is not properly inflated,
the tyre pressure monitoring system
warning light will illuminate (page
7-60).
19.After driving the vehicle for 10
minutes or 5 km (3 miles), check
the tyre pressure with the tyre
pressure gauge equipped with the
compressor. If the tyre pressure has
fallen below the correct tyre
pressure, inflate the tyre to the
correct pressure again following the
steps from number 14.
CAUTION
¾If the tyre
inflation pressure falls
below 130 kPa (1.3 kgf/cm2 or
bar, 18.9 psi), repair cannot be
done with the repair kit. Park the
vehicle on a level surface off the
right-of-way and contact an
expert repairer (we recommend
an Authorised Mazda Repairer).
¾If the tyre inflation pressure
continues to remain low after
repeating steps 13 to 20, park the
vehicle on a level surface
off the
right-of-way and contact an
expert repairer (we recommend
an Authorised Mazda Repairer).
NOTE
When checking the tyre inflation
pressure with the tyre pressure
gauge on the compressor unit,
make sure the compressor switch is
turned off.
20.The emergency flat tyre repair is
completed if the tyre air pressure
does not decrease. Drive the
vehicle carefully to the nearest
expert repairer (we recommend an
Authorised Mazda Repairer)
promptly and have the tyre
replaced. Mazda recommends that
the tyre be replaced with a new
one. If the tyre is to be repaired and
reused, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
Peel off the speed restriction sticker
after replacing the tyre.
If Trouble Arises
Flat Tyre
7-32

Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
1. Move the booster vehicle so that its battery is as close as possible to your
vehicle's battery.
2. Make sure that the power such as for the headlights and air conditioner is turned
off.
3. Remove the battery cover.
4. Turn off the booster vehicle's engine and connect the jumper leads in the
following order.
Make sure that the jumper leads are securely connected so that they do not
disconnect due to engine vibrations.
1st lead
Positive (+) terminal on the discharged battery
Positive (+) terminal on booster vehicle's battery
2nd lead
Negative (-) terminal on booster vehicle's battery
If Trouble Arises
Battery Runs Out
7-40

If a Warning Light Turns
On or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/flashes,
take appropriate action for each light.
There is no problem if the light turns
off, however if the light does not turn
off or turns
on/flashes again, consult
an expert repairer (we recommend an
Authorised Mazda Repairer).
The details for some warnings can be
viewed on the centre display or
multi-information display in the
instrument cluster.
Centre display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to
view the warning details.
NOTE
You can also display the currently
occurring warning by sliding the
commander knob to the left while on
the home screen of the centre display.
Multi-information display
1. Press the INFO switch on the
steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-23.
▼Brake System Warning Indication/
Warning Light (Red)
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the ignition is
switched on, and turns off a few
seconds later or when the engine is
started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
Refer to Inspecting Brake/Clutch Fluid
Level on page 6-30.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
expert repairer (we recommend an
Authorised Mazda Repairer) to have
the brakes inspected as soon as
possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
CAUTION
¾In addition, the
effectiveness of the
braking may diminish so you may
need to depress the brake pedal
more strongly than normal to stop
the vehicle.
¾(With M Hybrid)
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-49