key MAZDA MODEL CX-30 2019 (in English) Service Manual

(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
3. Make sure that the push button
start indication light (green) flashes.
4. Align the centre area of the emblem
on the transmitter with the centre
area of the push button start while
the push button start indicator light
(green) flashes.

1. Indicator light
2. Push button start
3. Transmitter
4. Emblem

5. Make sure that the push button
start indicator light (green) turns
on.
6. Press the push button start to start
the engine.
NOTE
xThe engine cannot be started
unless the clutch pedal is fully
depressed (manual transmission)
or the brake pedal is fully
depressed (automatic
transmission).
xIf there is a malfunction with the
push button start function, the
push button start indicator light
(amber) flashes. In this case, the
engine may start, however, have
the vehicle checked at an expert
repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
xIf the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle
checked at an expert repairer (we
recommend an Authorised
Mazda Repairer).
xTo switch the ignition position
without starting the engine,
perform the following operations
after the push button start
indicator light (green) turns on.
1. Release the clutch pedal
(manual transmission) or
brake pedal (automatic
transmission).
2. Press the push button start to
switch the ignition position.
The ignition switches in the
order of ACC, ON, and off
each time the push button
start is pressed. To switch the
ignition position again,
perform the operation from
the beginning.
▼Emergency Operation for Starting
the Engine
If the KEY warning indication (red) is
displayed, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
When Driving
Start/Stop Engine
4-9

possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine
starts. Other procedures necessary for
starting the engine such as having the
key in the cabin, and depressing the
clutch pedal (manual transmission) or
the brake pedal (automatic
transmission) are required.Turning the Engine Off
▼Turning the Engine
Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking ,
which could cause an accident and
serious injury.
1. Stop the vehicle completely.
2.(Manual transmission)
Shift into neutral and set the
parking brake.
(Automatic transmission)
Shift the selector lever to the P
position and set the parking brake.
3. Press the push button start to turn
off the engine. The ignition position
is off.
CAUTION
¾When leaving the vehicle, make sure
the push button start is off.
¾(SKYACTIV-D 1.8)
If the engine is started and stopped
repeatedly before it warms up, the
engine may speed up while the
vehicle is stopped to clean the
engine internally. Do not stop the
engine until the engine returns to
running at its normal speed.
When Driving
Start/Stop Engine
4-10

NOTE
xThe cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or
off, to cool the engine
compartment quickly.
xIf the system detects that the
remaining battery power of the key is
low when the ignition is switched
from ON to ACC or OFF, the
following is indicated.
Replace with a new battery before
the key becomes unusable.
Refer to Key Battery Replacement on
page 6-39.
A message is indicated in the display
of the instrument cluster.
Refer to KEY Warning Indication/
Warning Light (Red) on page 7-56.
x(Automatic transmission)
If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
▼Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number
of times while the engine is running or
the vehicle is being driven will turn the
engine
off immediately. The ignition
switches to ACC.
i-stop*
▼i-stop
The i-stop function automatically stops
the engine when the vehicle is stopped
at a
traffic light or stuck in
traffic, and
then restarts the engine automatically
to resume driving. The system provides
improved fuel economy, reduced
exhaust gas emissions, and eliminates
idling noise while the engine is
stopped.
Engine idle stopping and restarting
NOTE
xAfter parking the vehicle, make sure
that the ignition is switched OFF.
There is the possibility of the vehicle
moving if the vehicle is parked while
i-stop is operating.
xThe i-stop indicator light (green)
turns on under the following
conditions:
xWhen engine idling is stopped.
xThe i-stop indicator light (green)
turns off when the engine is
restarted.
When Driving
Start/Stop Engine
*Some models.4-11

xThe i-stop warning light (amber) is
not turned on/flashing.
xThe keyless entry & push button start
system functions are normal.
x(With M Hybrid)
xThe temperature and charge
condition of the M Hybrid battery
is good.
xThe Integrated Starter-Generator
(ISG) is in good condition.
x(Without M Hybrid)
xThe brake vacuum is
sufficiently
high.
xThe battery is in good condition.x(Manual transmission)
While vehicle is stopped
xThe vehicle speed is 3 km/h (1.8
mph) or less.
xThe shift lever is in the neutral
position.
xThe clutch pedal is not depressed.
While driving (With M Hybrid)
xThe vehicle speed is 17 km/h (11
mph) or less.
xThe gear shift indicator (GSI)
displays N.
xThe brake pedal is depressed.xThe shift lever is in the neutral
position.
xThe clutch pedal is not depressed.xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is not driven on a
slope.
x(Automatic transmission)
While vehicle is stopped
xThe selector lever is in the D or M
position (not in second gear fixed
mode).
xThe automatic transmission
fluid
has warmed up sufficiently.
xThe automatic transmission
fluid
temperature is not abnormally
high.
xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is stopped by
depressing the brake pedal.
xThe vehicle is not on a steep slope.xThe vehicle is not stopped
suddenly.
While driving (With M Hybrid)
xThe selector lever is in the D
position (not in second gear fixed
mode).
xThe vehicle is driven at a vehicle
speed of about 20 km/h (12 mph)
or faster after engine idling stops
while the vehicle is stopped.
xThe vehicle is driven at a vehicle
speed of about 30 km/h (19 mph)
or faster after engine idling stops
while driving.
xThe vehicle is not driven in sport
mode.
xThe automatic transmission fluid
has warmed up sufficiently.
xThe automatic transmission fluid
temperature is not abnormally
high.
xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
When Driving
Start/Stop Engine
4-14

Signal Warning Refer to
(Amber)
*i-stop Warning Indication/Warning Light*17-53
*Automatic Transmission Warning Indication/Warning Light*17-55
*AWD Warning Indication/Warning Light*17-56
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning
Light*17-55
*Tyre Pressure Monitoring System (TPMS) Warning Indication/Warn-
ing Light*1
Flashing
7-57
Tu r n s o n
7-60
(Red)KEY Warning Indication/Warning Light
*17-56
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-58
*Adaptive LED Headlights (ALH) Warning Indication/Warning Light*17-58
i-ACTIVSENSE Warning Indication/Warning Light*17-58
Exterior Light Warning Indication/Warning Light*17-58
Low Fuel Warning Indication/Warning Light 7-58
Engine Oil Level Warning Indication/Warning Light*17-59
*120 km/h Warning Light*17-57
Seat Belt Warning Indication/Warning Light (Front seat) 7-59
(Red)Seat Belt Warning Light (Rear seat) 7-59
When Driving
Instrument Cluster and Display
*Some models.4-33

Signal Warning Refer to
*Low Washer Fluid Level Warning Indication/Warning Light7-60
Door-Ajar Warning Indication 7-60
Liftgate-Ajar Warning Indication 7-60
Door-Ajar Warning Light 7-60
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few
seconds later or when the engine is started. If the light does not turn on or remains turned on, have
the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).
▼Indication/Indicator Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Indicator Refer to
(Green)Seat Belt Indicator Light (Rear seat) 2-24
*Front Passenger Air Bag Deactivation Indicator Light2-51
Security Indicator LightImmobilizer
System
3-48
Theft-Deterrent
System
3-50
Malfunction
7-56
(Green)KEY Indicator Light 4-5
(Green)
*i-stop Indicator Light4-18
When Driving
Instrument Cluster and Display
4-34*Some models.

6Maintenance and Care
How to keep your Mazda in top condition.
Essential Information................. 6-2
Introduction.......................... 6-2
Scheduled Maintenance............ 6-3
Scheduled Maintenance......... 6-3
Owner Maintenance............... 6-16
Owner Maintenance
Precautions......................... 6-16
Bonnet................................ 6-17
Engine Compartment
Overview............................ 6-19
Engine Oil........................... 6-24
Engine Coolant.................... 6-28
Brake/Clutch Fluid............... 6-30
Window and Headlight Washer
Fluid................................... 6-31
Body Lubrication.................. 6-31
Wiper Blades....................... 6-32
Battery................................ 6-36
Key Battery Replacement...... 6-39
Tyres................................... 6-41
Light Bulbs...........................6-44
Fuses.................................. 6-46
Appearance Care.................... 6-54
Exterior Care....................... 6-54
Interior Care........................ 6-59
6-1

Key Battery Replacement
▼Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not
flash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
¾Make sure the battery is installed
correctly. Battery leakage could occur
if it is not installed correctly.
¾When replacing the battery, be
careful not to touch any of the
internal circuitry and electrical
terminals, bend the electrical
terminals, or get dirt in the
transmitter as the transmitter could
be damaged.
¾There is the danger of explosion if
the battery is not correctly replaced.
¾Dispose of used batteries according
to the following instructions.
¾Insulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
¾Never disassemble.
¾Never throw the battery into fire or
water.
¾Never deform or crush.
¾Replace only with the same type
battery (CR2032 or equivalent).
The following conditions indicate that
the battery power is low:
xA message, “Low Key Fob Battery.
Replace Battery” is displayed on the
multi-information display when the
ignition is switched OFF.
xThe system does not operate and the
operation indicator light on the
transmitter does not flash when the
buttons are pressed.
xThe system's operational range is
reduced.
Incorrect battery replacement
operation may damage the key.
Replacing the battery at an expert
repairer (we recommend an
Authorised Mazda Repairer) is
recommended. If replacing the battery
by yourself, follow the instruction.
Replacing the key battery
1. Remove the lower cover while
pressing the knob in the direction
of the arrow.
2. Press in the tab to unlock the upper
cover.
Maintenance and Care
Owner Maintenance
6-39

No.FUSE RAT-
INGPROTECTED COMPONENT
F715 A
Fuel warmer
*
20 A
Fuel pump*
F8 15 A Engine control system
F9 15 A
Transmission control system
*
F10 15 A Engine control system
F11 7.5 A Air conditioner
F12 15 A Engine control system
F13 15 A
NOx sensor
*
F14 20 A
Front seat warmer*
F15 20 A
Headlight washer*
F16 15 A For protection of various circuits
F17ŠŠ
F18 15 A Accessory sockets
F19 60 A Power steering system
F20 15 A Headlight (LH) 1
F21 15 A Headlight (RH) 1
F22 15 A Keyless system
F23 30 A ABS, Dynamic stability control system
F24 15 A Headlight (LH) 2
F25 15 A Headlight (RH) 2
F26 7.5 A On board diagnostics
F27 25 A For protection of various circuits
F28 25 A For protection of various circuits
F29 15 A Windscreen washer
F30ŠŠ
F31 15 A Horn
F32 15 A Headlights
F33ŠŠ
F34ŠŠ
F35 50A ABS, Dynamic stability control system
F36ŠŠ
F37 40 A Rear window defogger
F38 50 A For protection of various circuits
Maintenance and Care
Owner Maintenance
6-50*Some models.

▼KEY Warning Indication/Warning
Light (Red)
“Keyless Entry System Malfunc. Have
the Vehicle Inspected” is displayed
This message is displayed if the
advanced keyless entry & push button
start system has a problem.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the message is indicated, or the push
button start indicator light (amber)
flashes, the engine may not start. If the
engine cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-9.
“Key Not Detected” is displayed
xIf the presence of the key cannot be
detected (dead battery, battery
malfunction, no key), it is displayed
when the driver attempts to start the
engine (push button start operation,
brake pedal depression).
xDisplayed when it is determined that
a key that was in the vehicle has
been removed from the vehicle. (Key
taken out warning. Other than
IG-OFF).
▼Security Indicator Light
If the security indicator light flashes
continuously while you are driving, do
not shut
off the engine. Go to an
expert repairer (we recommend an
Authorised Mazda Repairer) and have
it checked. If the engine is shut off
while the indicator light is
flashing , you
will not be able to restart it.
Make sure the key is within the
operational range for signal
transmission. Switch the ignition off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
Because the electronic codes are reset
when the immobilizer system is
repaired, the keys are needed. Make
sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
▼AWD Warning Indication/
Warning Light*
“AWD Malfunction. Front Wheel
Drive Only. Have the Vehicle
Inspected” is displayed/When the
light is turned on
The indication is displayed/the light
turns on under the following
conditions. The system may have a
malfunction. Have the vehicle checked
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.