engine oil MAZDA MODEL CX-30 2019 Owners Manual (in English)

Rocking the Vehicle
▼Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating , transmission failure, and
tyre damage.
If you must rock the vehicle to free it
from snow, sand or mud, depress the
accelerator slightly and slowly move
the shift lever/selector lever from 1 (D)
to R position.
Winter Driving
▼Winter Driving
Carry emergency gear, including tyre
chains, window scraper,
flares, a small
shovel, jumper leads, and a small bag
of sand or salt.
Ask an expert repairer (we recommend
an Authorised Mazda Repairer) to
check the following:
xHave the proper ratio of antifreeze in
the radiator.
Refer to Engine Coolant on page
6-28.
xInspect the battery and its leads.
Cold reduces battery capacity.
xUse an engine oil appropriate for the
lowest ambient temperatures that
the vehicle will be driven in (page
6-24).
xInspect the ignition system for
damage and loose connections.
xUse washer fluid made with
antifreezeŠbut do not use engine
coolant antifreeze for washer fluid
(page 6-31).
NOTE
xRemove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
xDo not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
xNever use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
Before Driving
Driving Tips
3-56

Driving In Flooded Area
▼Driving In Flooded Area
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
CAUTION
Do not drive the vehicle on flooded
roads as it could cause short circuiting
of electrical/electronic parts, or engine
damage or stalling from water
absorption. If the vehicle has been
immersed in water, consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
Turbocharger Information
(SKYACTIV-D 1.8)
▼Turbocharger Information
(SKYACTIV-D 1.8)
CAUTION
¾After driving at freeway speeds or up
a long hill, trailer towing for a long
time, idle the engine at least 30
seconds before stopping it.
Otherwise, the turbocharger could
be damaged. However, when i-stop
operates, idling is unnecessary.
¾Racing or over-revving the engine,
particularly after it's just been
started, can damage the
turbocharger.
¾To protect the engine from damage,
the engine is designed so that it
cannot be raced just after starting it
in extremely cold weather.
The turbocharger greatly enhances
engine power. Its advanced design
provides improved operation and
requires minimum maintenance.

To get the most from it, observe the
following.
1. Change engine oil and filter
according to Scheduled
Maintenance.
Refer to Europe on page 6-3.
Refer to Except Europe on page
6-6.
2. Use only recommended engine oil
(page 6-24). Extra additives are
NOT recommended.
Before Driving
Driving Tips
3-59

Cylinder Deactivation*
▼Cylinder Deactivation
The cylinder deactivation is a function
designed to reduce fuel consumption
and improve fuel economy by
deactivating 2 out of the 4 cylinders
while driving. The function constantly
determines which is better for driving;
4 cylinders or 2 cylinders, regardless of
the driver's operations, and it performs
the switching automatically.
When the cylinder deactivation
function does not operate
The cylinder deactivation function
does not operate under the following
conditions.
xThe selector lever is in the P, N, or R
position (automatic transmission), or
1st gear (manual transmission).
xThe engine oil temperature or engine
coolant temperature is low.
xAfter disconnecting the battery
terminals for some reason, such as
for battery replacement.
When Driving
Start/Stop Engine
4-20*Some models.

▼Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Warning Refer to
(Red)Brake System Warning Indication/Warning Light
*17-49
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn-
ing
7-50
ABS warning
7-52
Charging System Warning Indication/Warning Light*17-50
Engine Oil Warning Indication/Warning Light*17-50
High Engine Coolant Temperature Warning Indication 7-51
Power Steering Malfunction Indication/Indicator Light*17-51
Master Warning Indication 7-52
(Amber)Brake Control System Warning Indication/Warning Light
*17-52
Brake Override Warning Indication 7-53
Check Engine Indication/Light*17-53
Petrol Particulate Filter Warning Indication/Warning Light*1(SKYAC-
TIV-X 2.0)7-54
Diesel Particulate Filter Warning Indication/Warning Light
*1(SKYAC-
TIV-D 1.8)7-54
When Driving
Instrument Cluster and Display
4-32

Signal Warning Refer to
(Amber)
*i-stop Warning Indication/Warning Light*17-53
*Automatic Transmission Warning Indication/Warning Light*17-55
*AWD Warning Indication/Warning Light*17-56
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning
Light*17-55
*Tyre Pressure Monitoring System (TPMS) Warning Indication/Warn-
ing Light*1
Flashing
7-57
Tu r n s o n
7-60
(Red)KEY Warning Indication/Warning Light
*17-56
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-58
*Adaptive LED Headlights (ALH) Warning Indication/Warning Light*17-58
i-ACTIVSENSE Warning Indication/Warning Light*17-58
Exterior Light Warning Indication/Warning Light*17-58
Low Fuel Warning Indication/Warning Light 7-58
Engine Oil Level Warning Indication/Warning Light*17-59
*120 km/h Warning Light*17-57
Seat Belt Warning Indication/Warning Light (Front seat) 7-59
(Red)Seat Belt Warning Light (Rear seat) 7-59
When Driving
Instrument Cluster and Display
*Some models.4-33

Refer to the Information section in
the Mazda Connect Owner's
Manual.
CAUTION
¾When the maintenance period
arrives, have your vehicle inspected
by an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. If
maintenance is neglected, a
decrease in vehicle performance
may occur which could cause
damage. Have your vehicle
inspected before the maintenance
period arrives.
¾If the vehicle continues to be
driven after the engine oil
replacement period has passed, it
could cause damage to the engine.
Replace the engine oil before the
maintenance period arrives.
¾(SKYACTIV-D 1.8)
Depending on the vehicle use
conditions, engine oil replacement
is required due to engine oil
deterioration from fuel penetrating
the engine oil. If “Excessive Oil
Level. Have the Vehicle Inspected”
is displayed on the
multi-information display in the
instrument cluster, have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(SKYACTIV-D 1.8)
xWhen fuel filter (sedimentor)
draining is required. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
NOTE
xThe wrench indication/indicator
light may display/turn on earlier than
the preset period depending on
vehicle usage conditions.
xWhenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
Refer to the Information section in
the Mazda Connect Owner's
Manual.

▼Glow Indicator Light (SKYACTIV-D
1.8)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when
preheating is finished.

A problem in the system might be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe glow indicator light does not
turn on when the ignition is switched
ON or it remains on.
xThe glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the
engine and a long period of time has
elapsed since preheating
finished, the
preheating may be performed again
and the glow indicator light may turn
on.
When Driving
Instrument Cluster and Display
4-38

▼Indicators
1. Manual shift mode indication
2. Gear position indication
Manual shift mode indication
In manual shift mode, the “M” of the
shift position indication in the
instrument panel illuminates.
Gear position indication
The numeral for the selected gear
illuminates.

NOTE
xIf the gears cannot be shifted down
when driving at higher speeds, the
gear position indication will
flash
twice to signal that the gears cannot
be shifted down (to protect the
transmission).
xIf the automatic transmission fluid
(ATF) temperature becomes too
high, there is the possibility that the
transmission will switch to automatic
shift mode, cancelling manual shift
mode and turning off the gear
position indication illumination. This
is a normal function to protect the
AT. After the ATF temperature has
decreased, the gear position
indication illumination turns back on
and driving in manual shift mode is
restored.
x(SKYACTIV-D 1.8 (European
model))
If the engine oil temperature
becomes too high, there is the
possibility that the transmission will
switch to automatic shift mode,
cancelling manual shift mode and
turning off the gear position
indicator illumination. After the
engine oil temperature has
decreased, the gear position
indicator illumination turns back on
and driving in manual shift mode is
restored.
▼Gear Shift Indicator (GSI)*
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
When Driving
Automatic Transmission
*Some models.4-47

¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.

Do not get out of the vehicle while
the stop hold control is operating.
(Automatic transmission vehicle)
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before getting out of the vehicle,
switch the CTS off, apply the parking
brake, and then shift the selector lever
to the P position.

CAUTION
Turn the system off when the vehicle is
running on a chassis roller.
Heed the following cautions so that
the CTS can operate normally.
¾Turn the system off when the vehicle
is running on a chassis roller.
¾Do not modify the vehicle's
suspensions.
¾Always use wheels of the specified
size for the front and rear wheels.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for tyre replacement.

NOTE
xThe headway control does not detect
the following as physical objects.
xVehicles approaching in the
opposite direction
xPedestriansxStationary objects (stopped
vehicles, obstructions)
xIf a vehicle ahead is travelling at an
extremely low speed, the system may
not detect it correctly.
xIf there is a structure on the road or
an object (such as a monorail) at a
low height off the ground in front of
the vehicle, the system may operate.
Therefore, do not use the CTS.
xDo not use the CTS under conditions
in which close proximity warnings
are frequently activated.
xIf it is necessary to accelerate for a
lane change or the vehicle ahead
brakes suddenly causing you to close
in on the vehicle rapidly, accelerate
using the accelerator pedal or
decelerate using the brake pedal
depending on the conditions.
xWhile the CTS is in use, any intended
engine braking does not occur even
if you shift the shift lever (manual
transmission) or the selector lever
(automatic transmission). If
deceleration is required, lower the
vehicle speed setting or depress the
brake pedal.
xWhile braking by the CTS control is
operating , you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the CTS control is
operating, however, they may not
turn on while the vehicle is on a
down slope at the set vehicle speed
or travelling at a constant speed and
following a vehicle ahead.
xUnder the following conditions, the
CTS may not be able to detect white
(yellow) lines or vehicles ahead
correctly and the CTS may not
operate normally.
xThe forward sensing camera (FSC)
cannot recognise the area in front
of the vehicle due to soiling or fog.
When Driving
i-ACTIVSENSE
4-150

6Maintenance and Care
How to keep your Mazda in top condition.
Essential Information................. 6-2
Introduction.......................... 6-2
Scheduled Maintenance............ 6-3
Scheduled Maintenance......... 6-3
Owner Maintenance............... 6-16
Owner Maintenance
Precautions......................... 6-16
Bonnet................................ 6-17
Engine Compartment
Overview............................ 6-19
Engine Oil........................... 6-24
Engine Coolant.................... 6-28
Brake/Clutch Fluid............... 6-30
Window and Headlight Washer
Fluid................................... 6-31
Body Lubrication.................. 6-31
Wiper Blades....................... 6-32
Battery................................ 6-36
Key Battery Replacement...... 6-39
Tyres................................... 6-41
Light Bulbs...........................6-44
Fuses.................................. 6-46
Appearance Care.................... 6-54
Exterior Care....................... 6-54
Interior Care........................ 6-59
6-1

Scheduled Maintenance
▼Scheduled Maintenance
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system
and to efficient engine operation. Do not tamper with them.
All inspections and adjustments must be made by an expert repairer (we
recommend an Authorised Mazda Repairer).
▼Europe
Vehicles utilizing the vehicle status monitor feature (My Mazda Service):
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
For vehicles in European countries, except SKYACTIV-D 1.8 for Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
20,000 km (12,500 miles) or 12 months, whichever comes first. (after the previous
maintenance)
For SKYACTIV-D 1.8 vehicles in Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
10,000 km (6,250 miles) or 12 months, whichever comes
first. (after the previous
maintenance)
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
SKYACTIV-G 2.0 AND SKYACTIV-X 2.0
Engine oil &
filter
*1*2RRRRRRRRRRRR
Spark plugs
*4
SKYACTIV-G
2.0Replace every 120,000 km (75,000 miles).
SKYACTIV-X
2.0Replace every 64,000 km (40,000 miles).
Air filter
*5RRRR
Fuel lines and hoses IIIIII
Hoses and tubes for emission I I I I
SKYACTIV-D 1.8
Engine oil &
filter
*1*3RRRRRRRRRRRR
Maintenance and Care
Scheduled Maintenance
6-3