brake light MAZDA MODEL CX-5 2015 (in English) User Guide

Black plate (135,1)
2. Verify that the push button startindicator light (green) flashes.
NOTE
The push button start indicator light (green)
will flash even if the push button start is
pressed before depressing the brake pedal
(automatic transaxle) or the clutch pedal
(manual transaxle). If the clutch pedal is
depressed (manual transaxle) or the brake
pedal is depressed (automatic transaxle) under
this condition, the engine can be started by
resuming the procedure following this.
3. Touch the push button start using the backside of the key (as shown) while
the push button start indicator light
(green) flashes.
Key
Indicator light
Push button start
4. After the push button start indicatorlight (green) changes to full
illumination, press the push button start
with your finger. NOTE
lThe engine cannot be started unless the
clutch pedal is fully depressed (manual
transaxle) or the brake pedal is fully
depressed (automatic transaxle).
lIf there is a malfunction with the push
button start function, the push button start
indicator light (amber) flashes. In this case,
the engine may start, however, have the
vehicle checked at an Authorized Mazda
Dealer as soon as possible.
lIf the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If it
does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
lIf you just want to change the ignition
position (with a dead key battery), after the
push button start indicator light (green)
changes to illumination, release the brake
pedal (automatic transaxle) or the clutch
pedal (manual transaxle), and press the
push button start. The ignition switches in
the order of ACC, ON, and OFF each time
it is pressed. Once the ignition switches off,
the ignition position can no longer be
switched. Therefore, if the engine starts,
perform the operation from the beginning
again.
When Driving
Start/Stop Engine
4-7
CX-5_8DR2-EA-14A_Edition1 Page135
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (136,1)
qEmergency Operation for
Starting the Engine
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this could
indicate that the engine may not start
using the usual starting method (for
vehicles with a type A meter, messages
are displayed in the instrument cluster).
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can be
force-started. Press and hold the push
button start until the engine starts. Other
procedures necessary for starting the
engine such as having the key in the
cabin, and depressing the clutch pedal
(manual transaxle) or the brake pedal
(automatic transaxle) are required.
Turning the Engine Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle
is moving for any reason other than
in an emergency is dangerous.
Stopping the engine while the vehicle
is moving will result in reduced
braking ability due to the loss of
power braking, which could cause an
accident and serious injury.
1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral.
(Automatic transaxle)
Shift the shift lever to the P position.
3. Press the push button start to turn off the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure
the push button start is pressed to
off.
4-8
When Driving
Start/Stop Engine
CX-5_8DR2-EA-14A_Edition1 Page136
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (152,1)
Indication and method for taking action list
SignalWarning/Indicator Lights Page
Master Warning Light 4-28
Brake System Warning Light4-28
ABS Warning Light4-29
Charging System Warning Indication4-30
Engine Oil Warning Indication4-30
Check Engine Light4-31
High Engine Coolant Temperature Warning Light (Red) 4-31
AWD Warning Indication4-32
BSM OFF Indicator Light4-43
Automatic Transaxle Warning Indication4-32
Power Steering Malfunction Indication4-33
Air Bag/Front Seat Belt Pretensioner System Warning Light4-33
Low Fuel Warning Light4-34
Check Fuel Cap Warning Indication4-34
Seat Belt Warning Light4-34
4-24
When Driving
Instrument Cluster and Display
CX-5_8DR2-EA-14A_Edition1 Page152
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (153,1)
SignalWarning/Indicator Lights Page
Door-Ajar Warning Indication 4-35
Liftgate-Ajar Warning Indication4-36
Low Washer Fluid Level Warning Indication4-36
Tire Pressure Monitoring System Warning Light4-36
KEY Warning Indication4-38
Wrench Indication4-40
TCS/DSC Indicator Light4-40
TCS OFF Indicator Light4-40
AFS OFF Indicator Light4-40
Smart City Brake Support (SCBS) OFF Indicator Light4-41
Low Engine Coolant Temperature Indicator Light (Blue) 4-41
Shift Position Indication4-41
Headlight High-Beam Indicator Light4-42
Turn Signal/Hazard Warning Indicator Lights4-42
When Driving
Instrument Cluster and Display
4-25
CX-5_8DR2-EA-14A_Edition1 Page153
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (154,1)
SignalWarning/Indicator Lights Page
Security Indicator Light 4-42
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 4-42
Lights-On Indicator Light4-43
qType B
Warning/Indicator lights will appear in any of the highlighted areas
Signal Warning/Indicator Lights Page
Master Warning Light 4-28
Brake System Warning Light4-28
ABS Warning Light4-29
Charging System Warning Light4-30
Engine Oil Warning Light4-30
Check Engine Light4-31
High Engine Coolant Temperature Warning Light (Red) 4-31
4-26
When Driving
Instrument Cluster and Display
CX-5_8DR2-EA-14A_Edition1 Page154
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (156,1)
SignalWarning/Indicator Lights Page
Shift Position Indication 4-41
Headlight High-Beam Indicator Light4-42
Turn Signal/Hazard Warning Indicator Lights4-42
Security Indicator Light4-42
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 4-42
Lights-On Indicator Light4-43
qMaster Warning Light
This warning light stays on for a few
seconds when the ignition is switched
ON.
Type A
Displays when notification of the system
malfunctions is required.
Check the message indicated in the
display and consult an Authorized Mazda
Dealer.
Type B
The light illuminates continuously if any
one of the following occurs. Consult an
Authorized Mazda Dealer.
lThere is a malfunction in the battery
management system.
lThere is a malfunction in the brake
switch.
qBrake System Warning Light
This warning has the following functions:
Parking brake warning/Warning light
inspection
The light illuminates when the parking
brake is applied with the ignition switched
to START or ON. It turns off when the
parking brake is fully released.
4-28
When Driving
Instrument Cluster and Display
CX-5_8DR2-EA-14A_Edition1 Page156
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (157,1)
Low brake fluid level warning
If the brake warning light remains
illuminated even though the parking brake
is released, the brake fluid may be low or
there could be a problem with the brake
system. Park the vehicle in a safe place
immediately and contact an Authorized
Mazda Dealer.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:Driving with the brake system
warning light illuminated is
dangerous. It indicates that your
brakes may not work at all or that
they could completely fail at any
time. If this light remains
illuminated, after checking that the
parking brake is fully released, have
the brakes inspected immediately.
CAUTION
In addition, the effectiveness of the
braking may diminish so you may
need to depress the brake pedal more
strongly than normal to stop the
vehicle.
qABS Warning Light
The warning light stays on for a few
seconds when the ignition is switched
ON. If the ABS warning light stays on while
you're driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function normally
as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
NOTE
When the engine is jump-started to charge the
battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it
is the result of the weak battery and does not
indicate an ABS malfunction.
Recharge the battery.
q
Electronic Brake Force
Distribution System Warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may illuminate the brake
system warning light and the ABS
warning light simultaneously. The
problem is likely to be the electronic
brake force distribution system.
When Driving
Instrument Cluster and Display
4-29
CX-5_8DR2-EA-14A_Edition1 Page157
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (158,1)
WARNING
Do not drive with both the ABS warning
light and brake warning light
illuminated. Have the vehicle towed to
an Authorized Mazda Dealer to have
the brakes inspected as soon as
possible:Driving when the brake system
warning light and ABS warning light
are illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly
in an emergency stop than under
normal circumstances.
qCharging System Warning
Indication/Warning Light
Type B
This warning light illuminates when the
ignition is switched ON and turns off
when the engine is started.
Type A/Type B
If the warning light/indication illuminates
while driving, it indicates a malfunction
of the alternator or of the charging system.
Drive to the side of the road and park off
the right-of-way. Consult an Authorized
Mazda Dealer.
CAUTION
Do not continue driving when the
charging system warning light is
illuminated because the engine could
stop unexpectedly.
qEngine Oil Warning Indication/
Warning Light
Type B
This warning light illuminates when the
ignition is switched ON and turns off
when the engine is started.
Type A/Type B
This warning light/warning indication
indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil
pressure is low. Otherwise, it could
result in extensive engine damage.
If the light illuminates or the warning
indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the oil
pan.
3. Inspect the engine oil level (page 6-22). If it's low, add the appropriate amount
of engine oil while being careful not to
overfill.
4-30
When Driving
Instrument Cluster and Display
CX-5_8DR2-EA-14A_Edition1 Page158
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (166,1)
Warning light flashes
If the tire pressure monitoring system has
a malfunction, the tire pressure warning
light flashes for about 1 minute when the
ignition is switched ON and then
continues illuminating. Have your vehicle
checked by an Authorized Mazda Dealer
as soon as possible.
qKEY Warning Light (Red)/KEY
Indicator Light (Green)
Type A
“Keyless System Inspection Required ”
is displayed
This message is displayed if the advanced
keyless entry & push button start system
has a problem.
Contact an Authorized Mazda Dealer.
CAUTION
If the above message is indicated, or
the push button start indicator light
(amber) flashes, the engine may not
start. If the engine cannot be started,
try starting it using the emergency
operation for starting the engine, and
have the vehicle inspected at an
Authorized Mazda Dealer as soon as
possible.
Refer to Emergency Operation for
Starting the Engine on page 4-8. “
Set Power to OFF ”is displayed
This message is displayed when the
driver's door is opened without switching
the ignition off.
“ Key not found ”is displayed
This message is displayed when any of
the following operations is performed
with the key out of the operational range
or placed in areas inside the cabin where it
is difficult for the key to be detected.
lThe push button start is pressed with
the ignition switched off
lThe ignition is switched onlThe driver's door is opened or all doors
are closed without switching the
ignition off
“ Depress the Brake Pedal and Touch
the Key to the Start Button ”
(Automatic Transaxle vehicle)/ “Depress
the Clutch Pedal and Touch the Key to
the Start Button ”(Manual Transaxle
vehicle) is displayed
This message is displayed when any of
the following operations is performed
with the key out of the operational range
or placed in areas inside the cabin where it
is difficult for the key to be detected.
lThe push button start is pressed with
the ignition switched off
lBrake pedal (Automatic transaxle
vehicle)/Clutch pedal (Manual
transaxle vehicle) is depressed with the
ignition switched off
“ Key Battery is low ”is displayed
This message is displayed when the
remaining battery power of the key is low
and the ignition is switched from on to
off.
4-38
When Driving
Instrument Cluster and Display
CX-5_8DR2-EA-14A_Edition1 Page166
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A

Black plate (167,1)
NOTE
Because the key utilizes low-intensity radio
waves, the Key Removed From Vehicle
Warning may activate if the key is carried
together with a metal object or it is placed in a
poor signal reception area.
Type B
This indicator has two colors.
KEY Warning Light (Red)
When illuminated
If any malfunction occurs in the keyless
entry system, it illuminates continuously.
CAUTION
If the key warning indicator light
illuminates or the push button start
indicator light (amber) flashes, the
engine may not start. If the engine
cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-8.
When flashing
lUnder the following conditions, the
KEY warning light (red) flashes to
notify the driver that the ignition
cannot be switched from off.
lThe key battery is dead.lThe key is not within operational
range.
lThe key is placed in areas where it is
difficult for the system to detect the
signal (page 3-6).
lA key from another manufacturer
similar to the key is in the
operational range.
lUnder the following conditions, the
KEY warning light (red) will flash
continuously when the ignition has not
been switched off to notify the driver
that the key has been removed from the
vehicle. The KEY warning light (red)
will stop flashing when the key is back
inside the vehicle:
The ignition has not been switched off
and all the doors and the liftgate are
closed after removing the key from the
vehicle.
NOTE
Because the key utilizes low-intensity radio
waves, the Key Removed From Vehicle
Warning may activate if the key is carried
together with a metal object or it is placed in a
poor signal reception area.
KEY Indicator Light (Green)
When illuminated
When the brake pedal is depressed with
an automatic transaxle or the clutch pedal
is depressed with a manual transaxle, the
system confirms that the correct key is
inside the vehicle, the KEY indicator light
(green) illuminates, and the engine can be
started (page 4-3).
When flashing
When the ignition is switched from ON to
off, the KEY indicator light (green)
flashes for approximately 30 seconds
indicating that the remaining battery
power is low. Replace with a new battery
before the key becomes unusable.
Refer to Replace Electrical Battery on
page 6-33.
When Driving
Instrument Cluster and Display
4-39
CX-5_8DR2-EA-14A_Edition1 Page167
Thursday, November 21 2013 8:48 AM
Form No.8DR2-EA-14A