ignition MAZDA MODEL CX-5 2017 (in English) User Guide

3–3
Before Driving
Keys
A code number is stamped on the plate
attached to the key set; detach this plate
and store it in a safe place (not in the
vehicle) for use if you need to make a
replacement key (auxiliary key).
Also write down the code number and
keep it in a separate safe and convenient
place, but not in the vehicle.

If your key (auxiliary key) is lost, consult
your Authorized Mazda Dealer and have
your code number ready.
NOTE
The driver must carry the key to ensure the
system functions properly.


Auxiliary key
Transmitter
Key code number plate

To use the auxiliary key, pull out the
auxiliary key from the transmitter while
pressing the knob.

Knob

Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors and
the liftgate, and opens/closes the liftgate.
The system can start the engine without
having to take the key out of your purse or
pocket.
It can also help you signal for attention or
help.
Operating the theft-deterrent system is
also possible on theft-deterrent system-
equipped vehicles.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
For vehicles with the type A instrument
cluster, check the displayed message for
more information and, if necessary, have
the vehicle inspected at an Authorized
Mazda Dealer, according to the indication.
  KEY Warning Light (Red) Refer to Warning/Indicator Lights on
page 4-32 .
  Ignition Not Switched Off (STOP)
Warning Beep
 Refer to Ignition Not Switched Off (STOP) Warning Beep on page 7-40 .
  Key Removed from Vehicle Warning
Beep
 Refer to Key Removed from Vehicle Warning Beep on page 7-41 .

If you have a problem with the key,
consult an Authorized Mazda Dealer.

If your key is lost or stolen, consult an
Authorized Mazda Dealer as soon as
possible for a replacement and to make the
lost or stolen key inoperative.
CX-5_8FN1-EA-16L_Edition1.indb 32016/12/12 10:05:28

3–4
Before Driving
Keys
CAUTION
Radio equipment like this is governed
by laws in the United States.
Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.

NOTE
  The keyless entry system operation may
vary due to local conditions.
  The keyless entry system is fully
operational (door/liftgate lock/unlock)
when the ignition is switched off. The
system does not operate if the ignition is
switched to any position other than off.
  If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new battery,
refer to Key Battery Replacement (page
6-36 ).
  Battery life is about one year. Replace
the battery with a new one if the KEY
indicator light (green) fl ashes in the
instrument cluster (for vehicles with
a type A instrument cluster (page
4-32 ), messages are displayed in
the instrument cluster). Replacing
the battery about once a year is
recommended because the KEY warning
light/indicator light may not illuminate
or fl ash depending on the rate of battery
depletion.

  Additional keys can be obtained at
an Authorized Mazda Dealer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorized Mazda Dealer when
additional keys are required.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:05:28

3–5
Before Driving
Keys
Transmitter

Operation buttons
Operation indicator light

NOTE
 
 The headlights turn on/off by operating
the transmitter. Refer to Leaving Home
Light on page 4-55 .
  (With theft-deterrent system)  The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on page 3-47 .
  (With the advanced keyless function)  A beep sound can be heard for
confi rmation when the doors and the
liftgate are locked/unlocked using the
key. If you prefer, the beep sound can be
turned off.
 The volume of the beep sound can also be changed.
 Refer to Personalization Features on page 9-11 .

Use the following procedure to change the
setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
LOCK button on the key for
5 seconds or longer.
All of the doors and the liftgate lock and the beep sound activates at the
currently set volume. The setting
changes each time the LOCK button
on the key is pressed and the beep
sound activates at the set volume. (If
the beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
LOCK button on the key.
  Pressing a request switch.

The operation indicator light fl ashes when
the buttons are pressed.
CX-5_8FN1-EA-16L_Edition1.indb 52016/12/12 10:05:29

3–7
Before Driving
Keys
*Some models.
NOTE
  The system can be set to unlock all
doors by performing a single operation.
 Refer to Personalization Features on page 9-11 .
 Use the following procedure to change the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
UNLOCK button on the key for
5 seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the setting each time the UNLOCK
button is pressed (the sound of the
doors locking/unlocking can be
heard).
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
UNLOCK button on the key.
  Pressing a request switch.
  (Auto re-lock function)  After unlocking with the key, all doors
and the liftgate will automatically lock
if any of the following operations are
not performed within about 60 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
fl ash for confi rmation.
 The time required for the doors to lock
automatically can be changed.
 Refer to Personalization Features on page 9-11 .
  A door or the liftgate is opened.  The ignition is switched to any
position other than off.
  (With theft-deterrent system)  When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is
turned off, the hazard warning lights
will fl ash twice to indicate that the
system is turned off.

Power liftgate button *
To open/close the liftgate, press the power
liftgate button for one second or more
with the liftgate in the fully closed/open
position.
The hazard warning lights fl ash twice and
the liftgate opens/closes after the beep
sounds.


CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:05:29

3–8
Before Driving
Keys
Panic button
If you witness from a distance someone
attempting to break into or damage your
vehicle, press and hold the panic button
to activate the vehicle's alarm. Call
emergency services if necessary.

NOTE
The panic button will work whether any
door or the liftgate is open or closed.

(Turning on the alarm)
Pressing the panic button for 1 second or
more will trigger the alarm for about
2 minutes and 30 seconds, and the
following will occur:
  The horn sounds intermittently.  The hazard warning lights fl ash.
(Turning off the alarm)
The alarm stops by pressing any button on
the key.
Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Starting the Engine
NOTE
   Starting the engine may be possible
even if the key is outside of the vehicle
and extremely close to a door and
window, however, always start the
engine from the driver's seat.
 If the vehicle is started and the key is not in the vehicle, the vehicle will
not restart after it is shut off and the
ignition is switched to off.
  The luggage compartment is out of the
assured operational range, however,
if the key (transmitter) is operable the
engine will start.

With the advanced keyless function


Interior antenna Operational range

Without the advanced keyless function


Interior antenna Operational range

CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:05:29

3–13
Before Driving
Doors and Locks
NOTE
  Always stop the engine and lock the
doors. In addition, to prevent theft of
valuables, do not leave them inside the
cabin.
  If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
  Around the dashboard  In the storage compartments such as
the glove compartment or the center
console
  Next to a communication device such
as a mobile phone
  When the ignition is switched to ACC
or ON, the vehicle lock-out prevention
feature prevents you from locking
yourself out of the vehicle.
 All doors and the liftgate will automatically unlock if they are locked
using the power door locks with any
door or the liftgate open.
 The vehicle lock-out prevention feature does not operate while the ignition is
switched off.
 When any door is opened from the outside while the key is inside the
vehicle, the closed doors are locked. All
the doors are automatically unlocked by
closing the open door.
 (With the advanced keyless function)  The beep sound is heard for about
10 seconds to notify the driver that the
key has been left in the vehicle.
 (Without the advanced keyless
function)
 The horn sound is heard twice to notify
the driver that the key has been left in
the vehicle.
  (Door unlock (control) system with
collision detection)
 This system automatically unlocks
the doors and the liftgate in the event
the vehicle is involved in an accident
to allow passengers to get out of the
vehicle immediately and prevent being
trapped inside. While the ignition
is switched ON and in the event the
vehicle receives an impact strong
enough to infl ate the air bags, all the
doors and the liftgate are automatically
unlocked after about 6 seconds have
elapsed from the time of the accident.
 The doors and the liftgate may not unlock depending on how an impact
is applied, the force of the impact, and
other conditions of the accident.
 If door-related systems or the battery is malfunctioning, the doors and the
liftgate will not unlock.

CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:05:30

3–15
Before Driving
Doors and Locks
NOTE
  The system can be set to unlock all
doors by performing a single operation.
 Refer to Personalization Features on page 9-11 .
 Use the following procedure to change the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
UNLOCK button on the key for
5 seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the setting of pressing the driver's
request switch once or twice to
unlock all doors and the liftgate
each time the UNLOCK button is
pressed (the sound of the doors
locking/unlocking can be heard).
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
UNLOCK button on the key.
  Pressing a request switch.   Confi rm that all doors and the liftgate
are securely locked.
 For the liftgate, move it without pressing the electric liftgate opener to
verify that the liftgate has not been left
ajar.
  All doors and the liftgate cannot be
locked when any door or the liftgate is
open.
  It may require a few seconds for the
doors to unlock after the request switch
is pressed.
  A beep sound is heard for confi rmation
when the doors and the liftgate are
locked/unlocked using the request
switch. If you prefer, the beep sound can
be turned off.
 The volume of the beep sound can also be changed. Refer to Personalization
Features on page 9-11 .
 Use the following procedure to change
the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
LOCK button on the key for
5 seconds or longer.
All of the doors and the liftgate lock and the beep sound activates at the
currently set volume. The setting
changes each time the LOCK button
on the key is pressed and the beep
sound activates at the set volume. (If
the beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
LOCK button on the key.
  Pressing a request switch.
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:30

3–16
Before Driving
Doors and Locks
  (With theft-deterrent system)  The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on page 3-47 .
  The setting can be changed so that
the doors and the liftgate are locked
automatically without pressing the
request switch.
 Refer to Personalization Features on page 9-11 .
 (Auto-lock function)  A beep sound is heard when all doors
and the liftgate are closed while the
advanced key is being carried. All doors
and the liftgate are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights
fl ash once. (Even if the driver is in the
operational range, all doors and the
liftgate are locked automatically after
about 30 seconds.) If you are out of
the operational range before the doors
and the liftgate are completely closed
or another key is left in the vehicle, the
auto-lock function will not work. Always
make sure that all doors and the liftgate
are closed and locked before leaving the
vehicle. The auto-lock function does not
close the power windows.
   Auto re-lock function  After unlocking with the request
switch, all doors and the liftgate
will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your
vehicle has a theft-deterrent system,
the hazard warning lights will fl ash for
confi rmation.
 The time required for the doors to lock
automatically can be changed.
 Refer to Personalization Features on page 9-11 .
  Opening a door or the liftgate.  Switching the ignition to any position
other than off.


Locking, Unlocking with Transmitter
All doors and the liftgate can be locked/
unlocked by operating the keyless entry
system transmitter, refer to Keyless Entry
System (page 3-3 ).
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:30

3–17
Before Driving
Doors and Locks
Locking, Unlocking with Door-Lock Switch
All doors and the liftgate lock
automatically when the lock side is
pressed. They unlock when the unlock side
is pressed.
Driver's door

Unlock
Lock

Front passenger's door

Unlock
Lock

To lock all the doors and the liftgate from
an open front door, press the lock side of
the door lock switch and then close the
door.
NOTE
When locking the doors this way, be
careful not to leave the key inside the
vehicle.

Auto Lock/Unlock Function
WARNING
Do not pull the inner handle on a front
door: Pulling the inner handle on a front
door while the vehicle is moving
is dangerous. Passengers can fall
out of the vehicle if the door opens
accidentally , which could result in
death or serious injury.
  When the vehicle speed exceeds
20 km/h (12 mph), all doors and the
liftgate lock automatically.
   When the ignition is switched off,
all doors and the liftgate unlock
automatically.

These functions can also be disabled so
that they do not operate.
Auto lock/unlock function setting
change using door-lock switch
The doors and the liftgate can be set to
lock or unlock automatically by selecting
any one of the functions from the
following table and using the driver's door-
lock switch on the interior door panel.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:05:30

3–18
Before Driving
Doors and Locks
NOTE
  Function number 3 in the following
table is the factory setting for your
vehicle.
  There are only a total of six auto lock/
unlock settings available for automatic
transaxle vehicles, and three for manual
transaxle vehicles. Be sure to press the
unlock side of the driver's door-lock
switch the correct number of times
according to the selected function
number. If the switch is mistakenly
pressed seven times on an automatic
transaxle vehicle or four times on a
manual transaxle, the procedure will
be cancelled. If this occurs, start the
procedure from the beginning.


Function number Function *1
1 The auto door-lock function is
disabled.
2 All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
3 (Factory Setting) All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
All the doors and the liftgate unlock
when the ignition is switched from
ON to Off.
4 (Automatic transaxle vehicles only)

When the ignition is switched ON
and the selector lever is shifted from
park (P) to any other gear position,
all the doors and the liftgate lock
automatically.
5 (Automatic transaxle vehicles only)

When the ignition is switched ON
and the selector lever is shifted from
park (P) to any other gear position,
all the doors and the liftgate lock
automatically.
When the selector lever is shifted to
park (P) while the ignition is switched
ON, all the doors and the liftgate
unlock automatically.
6 (Automatic transaxle vehicles only)

All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
When the selector lever is shifted to
park (P) while the ignition is switched
ON, all the doors and the liftgate
unlock automatically.
*1 Other settings for the auto door lock function are available at an Authorized Mazda Dealer. For
details consult an Authorized Mazda Dealer. Refer
to Personalization Features on page 9-11 .


CX-5_8FN1-EA-16L_Edition1.indb 182016/12/12 10:05:31