low beam MAZDA MODEL CX-7 2012 Owners Manual (in English)

Black plate (206,1)
Signal Warning/Indicator Lights Page
Check Engine Light 5-49
ABS Warning Light 5-48
Air Bag/Front Seat Belt Pretensioner System Warning Light 5-50
Low Fuel Warning Light 5-50
Check Fuel Cap Warning Light 5-50
Seat Belt Warning Light 5-51
Door-Ajar Warning Light 5-52
Low Washer Fluid Level Warning Light 5-52
Automatic Transaxle Warning Light 5-52
AWD Warning Light 5-53
Tire Pressure Monitoring System Warning Light 5-53
KEY Warning Light (Red)/KEY Indicator Light (Green) 5-55
Security Indicator Light 5-57
Headlight High-Beam Indicator Light 5-57
Shift Position Indicator Light 5-57
TCS/DSC Indicator Light 5-58
5-46
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
CX-7_8CG3-EA-11J_Edition1 Page206
Saturday, September 24 2011 10:32 AM
Form No.8CG3-EA-11J

Black plate (217,1)
NOTE
The advanced key can be set so that the KEY
indicator light (green) does not flash even if
the battery power is low.
Refer to Personalization Features on page
10-8.
qSecurity Indicator Light
This indicator light starts flashing every 2
seconds when the ignition is switched
from ON to ACC and the immobilizer
system is armed.
The light stops flashing when the ignition
is switched ON with the correct ignition
key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then turns off.
If the engine does not start with the
correct ignition key, and the security
indicator light keeps illuminating or
flashing, the system may have a
malfunction. Consult an Authorized
Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:lThe high-beam headlights are on.lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
This indicates the selected shift position
when the ignition is switched to ON.
Gear position indicator
In manual mode, the“M”of the shift
position indicator illuminates and the
numeral for the selected gear displays in
the gear position indicator.
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-57
CX-7_8CG3-EA-11J_Edition1 Page217
Saturday, September 24 2011 10:32 AM
Form No.8CG3-EA-11J

Black plate (226,1)
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights have xenon fusion bulbs that produce a bright white
beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs yourself:
Replacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion
bulbs require high voltage, you could receive an electric shock if the bulbs are
handled incorrectly. Consult an Authorized Mazda Dealer when the replacement is
necessary.
NOTE
If the headlights flicker, or the brightness weakens, the bulb-life may be depleted and a replacement is
necessary. Consult an Authorized Mazda Dealer.
qHeadlight High-Low Beam
Press the lever forward to turn on the high
beams.
Pull the lever back to its original position
for the low beams.
High beam
Low beam
qFlashing the Headlights
To flash the headlights, pull the lever fully
towards you (the headlight switch does
not need to be on). The lever will return to
the normal position when released.
OFF
Flashing
5-66
Driving Your Mazda
íSome models.
Switches and Controls
CX-7_8CG3-EA-11J_Edition1 Page226
Saturday, September 24 2011 10:32 AM
Form No.8CG3-EA-11J

Black plate (359,1)
Displayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
(Actual view)Both bumper ends are not displayed.
Both bumper ends are not displayed.
Object
NOTElThe displayable range varies depending on the vehicle and road conditions.lThe displayable range is limited. Objects under the bumper or around the bumper ends cannot be
displayed.
lThe distance appearing in the displayed image is different from the actual distance because the
rear view parking camera is equipped with a specific lens.
lSome optionally installed vehicle accessories may be picked up by the camera. Do not install any
optional parts that can interfere with the camera view, such as illuminating parts or parts made of
reflective material.
lIt may be difficult to see the display under the following conditions, however, it does not indicate a
malfunction.
lIn darkened areas.lWhen the temperature around the lens is high/low.lWhen the camera is wet such as on a rainy day or during periods of high humidity.lWhen foreign material such as mud is stuck around the camera.lWhen the camera lens reflects sunlight or headlight beams.lIf the camera picks up a high-intensity light such as sunlight reflected off the vehicle body, a
bright belt (light line) may appear on the display. (Smear phenomenon)
lImage display may be delayed if the temperature around the camera is low.
Interior Comfort
Interior Equipment
6-121
CX-7_8CG3-EA-11J_Edition1 Page359
Saturday, September 24 2011 10:33 AM
Form No.8CG3-EA-11J

Black plate (434,1)
Light Bulbs
Headlights (Low beam) Headlights (High beam)
High-mount brake lightFog lights
Side turn signal lights
License plate lights
Brake lights/Taillights Overhead light (Front)/Map lights Overhead light (Rear)
Front side marker lights
Rear turn signal lights
Rear side marker lights
Reverse lights
Luggage compartment light
Some models. Front turn signal lights/Parking lights
8-42
Maintenance and Care
Owner Maintenance
CX-7_8CG3-EA-11J_Edition1 Page434
Saturday, September 24 2011 10:33 AM
Form No.8CG3-EA-11J

Black plate (435,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Replacing a headlight bulb
High-beam bulb
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.3. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the high-beam bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
4. Disconnect the bulb from the electrical
connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
5. Install the new bulb in the reverse order
of the removal procedure.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulb)
1. Make sure the headlight switch is off.
Maintenance and Care
Owner Maintenance
8-43
CX-7_8CG3-EA-11J_Edition1 Page435
Saturday, September 24 2011 10:33 AM
Form No.8CG3-EA-11J

Black plate (436,1)
2. If you are changing the right low-beam
bulb, start the engine, turn the steering
wheel all the way to the right, and turn
off engine. If you are changing the left
low-beam bulb, turn the steering wheel
to the left.
3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Detach the electrical connector from
the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.7. Swing the retaining spring out and
away to free the bulb.
Sealing
cover
8. Carefully remove the bulb from the
socket by pulling it straight back.
9. Replace the bulb.
10. Install the new bulb in the reverse
order of the removal procedure.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
8-44
Maintenance and Care
Owner Maintenance
CX-7_8CG3-EA-11J_Edition1 Page436
Saturday, September 24 2011 10:33 AM
Form No.8CG3-EA-11J

Black plate (445,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
18 H/L CLEAN/ROOF 20 A Moonroof
í
19 DEF 30 A Rear window defroster
20 TNS 15 A Parking lights, License plate lights, Illumination
21 A/C 10 A Air conditioner
22 TRAILER/TCM 20 A Transaxle control system
í
23 HEAD HI RH 15 A Headlight high beam (RH)
24 HEAD HI LH 15 A Headlight high beam (LH)
25 HEAD LO RH 15 A Headlight low beam (RH)
26 HEAD LO LH 15 A Headlight low beam (LH)
27 ETC 10 A Engine control system
í
28 ENG BAR 2 7.5 A Engine control system
29 ECM 10 A Engine control system
30 INJ 2 10 A Engine control system
í
31 ENG BAR 1 15 A Engine control system
32 FOG 15 A Fog lightsí
33 STOP 10 A Brake lights
34 HORN 20 A Horn
35
25 A Engine control system
36 HAZARD 10 A Hazard warning flashers, Turn signals
Maintenance and Care
Owner Maintenance
8-53íSome models. CX-7_8CG3-EA-11J_Edition1 Page445
Saturday, September 24 2011 10:34 AM
Form No.8CG3-EA-11J

Black plate (512,1)
2.5-liter engine
Item Weight
GVWR (Gross Vehicle Weight Rating) 2,125 kg (4,685 lbs)
GAWR (Gross Axle Weight Rating)Front 1,104 kg (2,434 lbs)
Rear 1,025 kg (2,260 lbs)
qAir Conditioner
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage ECE R (SAE)
HeadlightsHigh beam 60 HB3 (#9005)
Low beamHalogen 55 H7 (H7)
Xenon fusion 35 D2S (D2S)
Front turn signal lights/Parking lights 28/8―(#7444NA)
Front side-marker lights 5 W5W (#168)
Fog lights
í55 H11 (H11)
Side turn signal lights (Integrated with outside mirrors)íLED*1―(―)
High-mount brake light LED*1―(―)
Rear turn signal lights 21 WY21W (―)
Brake lights/Taillights 21/5 W21/5W (#7743)
Reverse lights 21 W21W (#7440)
License plate lights 5 W5W (#168)
Rear side-marker lights 5 W5W (#168)
*1 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulbCategory
Wattage ECE R
Overhead lights (Front)/Map lights 5 W5W
Overhead light (Rear) 10―
Luggage compartment light 10―
Vanity mirror light 1.8―
10-6íSome models.
Specifications
CX-7_8CG3-EA-11J_Edition1 Page512
Saturday, September 24 2011 10:34 AM
Form No.8CG3-EA-11J

Black plate (518,1)
E
Engine Coolant Temperature
Gauge ................................................ 5-42
Exhaust Gas ........................................ 4-5
Exterior Care ..................................... 8-58
F
Flasher
Hazard warning .......................... 5-75
Headlights .................................. 5-62
Flat Tire ............................................... 7-3
Changing ...................................... 7-6
Spare tire and tool storage ............ 7-3
Fluids
Classification .............................. 10-4
Owner maintenance ................... 8-16
Fog Lights ......................................... 5-68
Foot Brake .......................................... 5-5
Front Seats
(Electrically Operated Seats) ............... 2-4
Front Seats
(Manually Operated Seats) ................. 2-2
Fuel
Filler lid and cap ........................ 3-39
Gauge ......................................... 5-43
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-49
Panel description ........................ 8-52
Replacement ............................... 8-49
G
Glove Compartment ........................ 6-126
H
Hazard Warning Flasher .................... 5-75
H
Hazardous Driving .............................. 4-8
Headlights
Control ....................................... 5-62
Flashing ...................................... 5-66
High-low beam .......................... 5-66
Leveling ..................................... 5-67
HomeLink Wireless Control
System .............................................. 5-75
Hood Release .................................... 3-40
Horn .................................................. 5-74
I
Ignition
Keys ........................................... 3-21
Switch .......................................... 5-2
Illuminated Entry System ............... 6-104
Immobilizer System
(with Advanced Key) ........................ 3-45
Immobilizer System
(without Advanced Key) ................... 3-49
Indicator Lights ................................. 5-45
BSM OFF ................................... 5-59
Cruise ......................................... 5-58
Headlight high-beam .................. 5-57
Security ...................................... 5-57
Shift position .............................. 5-57
TCS OFF .................................... 5-58
TCS/DSC ................................... 5-58
Turn-signal/hazard warning ....... 5-59
Information Display ........................ 6-106
Audio display ........................... 6-107
Climate control display ............ 6-107
Information display functions ... 6-106
Instrument Cluster ............................. 5-40
Interior Care ...................................... 8-63
Interior Lights ................................. 6-104
11-4
Index
CX-7_8CG3-EA-11J_Edition1 Page518
Saturday, September 24 2011 10:34 AM
Form No.8CG3-EA-11J