key MAZDA MODEL CX-9 2016 (in English) Owner's Guide

4–6
When Driving
Start/Stop Engine
N O T E
 


y The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
 


y The engine can be started when the
push button start is pressed from off,
ACC, or ON.
 


y The push button start system functions
(function which can start the engine
by only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an Authorized Mazda
Dealer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
  Refer to Engine Start Function When
Key Battery is Dead on page 4-8 .
 


y After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
  This is for improved exhaust gas
puri¿ cation and does not indicate any
parts defect.
 


y Engine-starting is controlled by the
spark ignition system.
  This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical ¿ eld strength of radio
noise.

1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on. 4. Continue to press the brake pedal
¿ rmly until the engine has completely
started.
5. Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
N O T E
The starter will not operate if the selector
lever is not in P or N and the brake pedal
is not depressed suf¿ ciently.

6. Verify that the KEY indicator light
(green) (if equipped) in the instrument
cluster and the push button start
indicator light (green) illuminate.


Indicator light
Push button start

KEY indicator light
(green)/ KEY
warning light (red)

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–7
When Driving
Start/Stop Engine
NOTE
 


y If the push button start indicator
light (green) À ashes, make sure that
the key is being carried (for vehicles
with a type A instrument cluster (page
4-32 ), messages are displayed in the
instrument cluster).
 


y If the push button start indicator light
(green) À ashes with the key being
carried, touch the key to the push button
start and start the engine (for vehicles
with a type A instrument cluster (page
4-32 ), messages are displayed in the
instrument cluster). Refer to Engine
Start Function When Key Battery is
Dead on page 4-8 .

CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting
or from switching the ignition to
ACC or ON (for vehicles with a type
A instrument cluster (page 4-32 ),
messages are displayed in the
instrument cluster). Have your vehicle
inspected at an Authorized Mazda
Dealer as soon as possible.

N O T E
 


y Under the following conditions, the
KEY warning light (red) À ashes after
the push button start is pressed. This
informs the driver that the push button
start will not switch to ACC, even
if it is pressed from off (for vehicles
with a type A instrument cluster (page
4-32 ), messages are displayed in the
instrument cluster).
 


y The key battery is dead.



y The key is out of operational range.



y The key is placed in areas where it is
dif¿ cult for the system to detect the
signal (page 3-7 ).




y A key from another manufacturer
similar to the key is in the
operational range.
 


y (Forced engine starting method) 
 If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) À ashes, this
could indicate that the engine may not
start using the usual starting method
(for vehicles with a type A instrument
cluster (page 4-32 ), messages are
displayed in the instrument cluster).
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine, such as having the key in the
cabin, and depressing the brake pedal
are required.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–8
When Driving
Start/Stop Engine
 


y When the engine is force-started, the
KEY warning light (red) (if equipped)
remains illuminated and the push button
start indicator light (amber) remains
À ashing.




y When the selector lever is in the neutral
(N) position, the KEY indicator light
(green) (if equipped) and the push
button start indicator light (green) do
not illuminate.

7. Press the push button start after both
the KEY indicator light (green) (if
equipped) in the instrument cluster and
the push button start indicator light
(green) illuminate.
N O T E
 


y After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
 


y After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.

8. After starting the engine, let it idle for
about ten seconds.
N O T E
 


y Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
 


y If the engine does not start the ¿ rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-23 ).

Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
 


¾ Metal parts of other keys or metal
objects touch the key.
 

 


¾ Spare keys or keys for other vehicles
equipped with an immobilizer
system touch or come near the key.
 

 


¾ Devices for electronic purchases,
or security passage touch or come
near the key.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–9
When Driving
Start/Stop Engine
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:

1. Continue to depress the brake pedal
¿ rmly until the engine has completely
started.
2. Verify that the push button start
indication light (green) À ashes.
3. Touch the push button start using the
backside of the key (as shown) while
the push button start indicator light
(green) À ashes.


Transmitter

N O T E
When touching the push button start using
the backside of the key as shown in the
illustration, touch the push button start
with the lock switch side of the key facing
up.

4. Verify that the push button start
indicator light (green) turns on.
5. Press the push button start to start the
engine.
N O T E
 


y The engine cannot be started unless the
brake pedal is fully depressed.
 


y If there is a malfunction with the push
button start function, the push button
start indicator light (amber) À ashes.
In this case, the engine may start,
however, have the vehicle checked at an
Authorized Mazda Dealer as soon as
possible.
 


y If the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If
it does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
 


y To switch the ignition position without
starting the engine, perform the
following operations after the push
button start indicator light (green) turns
on.

1. Release the brake pedal.
2. Press the push button start to switch
the ignition position. The ignition
switches in the order of ACC, ON,
and off each time the push button
start is pressed. To switch the
ignition position again, perform the
operation from the beginning.


$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–10
When Driving
Start/Stop Engine
Emergency Operation for Starting
the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) À ashes, this could indicate that
the engine may not start using the usual
starting method (for vehicles with a type
A instrument cluster (page 4-32 ),
messages are displayed in the instrument
cluster). Have your vehicle inspected
at an Authorized Mazda Dealer as soon
as possible. If this occurs, the engine
can be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine such as having the key in the
cabin, and depressing the brake pedal are
required.
Turning the Engine Off
WARNING
Do not stop the engine while the vehicle
is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking, which
could cause an accident and serious
injury.

1. Stop the vehicle completely.
2. Shift the selector lever to the P position
and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.

CAUTION
When leaving the vehicle, make sure
the push button start is off .

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–11
When Driving
Start/Stop Engine
N O T E
 
y The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
 


y If the system detects that the remaining
battery power of the key is low when the
ignition is switched from ON to ACC or
OFF, the following is indicated.
  Replace with a new battery before the
key becomes unusable.
  Refer to Key Battery Replacement on
page 6-40 .
 (Vehicle equipped with Type A
instrument cluster)

 A message is indicated in the display of
the instrument cluster.
  (Vehicle equipped with Type B
instrument cluster)

 The KEY indicator light (green) À ashes
for approximately 30 seconds.
 
 Refer to Warning/Indicator Lights on
page 4-32 .
 





y If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.
 





Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–34
When Driving
Instrument Cluster and Display
*Some models.
Signal Warning Page

* Tire Pressure Monitoring System Warning Light *1 Flashing
7-33 ,
Illuminate
7-38


(Amber) * KEY Warning Indication 7-33


(Red) * KEY Warning Light *1 Malfunction
7-33 ,
Except
malfunction
7-38

(Amber)
* High Beam Control System (HBC) Warning Indication/Warning Light *1 7-33

* Blind Spot Monitoring (BSM) Warning Indication/Warning Light *1 7-33


(Amber) * Mazda Radar Cruise Control (MRCC) Warning Indication 7-33


(Amber) * Lane-keep Assist System (LAS) & Lane Departure Warning System
(LDWS) Warning Indication 7-33

LED Headlight Warning Light 7-33

(Amber)
* Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning
Indication 7-38

Low Fuel Warning Indication/Warning Light 7-38

* Check Fuel Cap Warning Indication/Warning Light *1 7-38

Seat Belt Warning Light 7-38

Engine Oil Level Warning Light 7-38
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–36
When Driving
Instrument Cluster and Display
*Some models.
Indication/Indicator Lights
These lights turn on or À ash to notify the user of the system operation status or a system
malfunction.

Signal Indicator Page

Front Passenger Air Bag Deactivation Indicator Light *1 2-65


(White/Green) KEY Indication/Indicator Light 4-5

Security Indicator Light *1 3-47

Wrench Indication/Indicator Light *1 4-38


(Blue) * Low Engine Coolant Temperature Indicator Light 4-38

Shift Position Indication 4-42

Lights-On Indication/Indicator Light 4-49

Headlight High-Beam Indicator Light Headlight High-Low
Beam
4-53 ,
Flashing the Headlights
4-53

Turn Signal/Hazard Warning Indicator Lights Turn and Lane-Change
Signals
4-55 ,
Hazard Warning Flasher
4-62

Brake Pedal Operation demand Indicator Light 4-68

TCS/DSC Indicator Light *1 (Flashes)
Traction Control System
(TCS)
4-74 ,
Dynamic Stability
Control (DSC)
4-76
(Turns on)
7-33
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










5–60
Interior Features
Audio Set
Deleting a favorite
1. Select the
icon on the home screen
to display the Communication screen.
2. Select
to display the favorites
list.
3. Select
.
4. Select
.
5. Select the contact information which
you would like to delete.
6. Select
.
Changing the display order of your
favorites list
1. Select the
icon on the home screen
to display the Communication screen.
2. Select
to display the favorites
list.
3. Select
.
4. Select
.
5. The contact can be moved after it is
selected.
6. Slide the contact or move it using the
commander switch, then select
.
Changing contact name of your
favorites
1. Select the
icon on the home screen
to display the Communication screen.
2. Select
to display the favorites
list.
3. Select
.
4. Select
.
5. Select the contact to display the
keyboard screen.
6. If a new name is input and
is
selected, the contact name is stored.

N O T E
If the contact is long-pressed when the
favorites list is displayed, the contact
information can be edited (deleted,
moved).

Telephone Number Input
N O T E
Practice this while parked until you are
con¿ dent you can do it while driving in a
non-taxing road situation. If you are not
completely comfortable, make all calls
from a safe parking position, and only
start driving when you can devote your full
attention to driving.

1. Select the icon on the home screen
to display the Communication screen.
2. When
is pressed, the dial pad
is displayed.
3. Input the telephone number using the
dial pad.
4. Select
to make the call.

Numeral or symbol entry
Use the dial pad.
Long-press the
to input +.
Select
to delete the currently input
value.
Long-press
to delete all input values.
Redial Function
Makes a call to the last person called
(latest person on outgoing call record)
from the mobile phone/vehicle.

1. Press the talk button.
2. Wait for the beep sound.
3. Say: “Redial”

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










5–66
Interior Features
Audio Set
Example of use (verify unread E-mail)
1. Select the
icon on the home screen
to display the Communication screen.
2. Select
to display the inbox.



3. Select the unread message displayed in
bold.
4. The details of the message are
displayed and replying to the message,
making a call, or playback can be
performed.

Changing account for displaying
(E-mail only)
1. Select
.
2. Select the account which you would
like to display. Only the messages for
the selected account are displayed in
the inbox.

Editing preset messages
1. Select the
icon on the home screen
to display the Communication screen.
2. Select
.
3. Select
.
4. Select the preset message which you
would like to edit. The keyboard screen
is displayed.
5. When the message is input and
is
selected, the message is stored as a
preset message.

N O T E
 


y Select the icon to change the
language.
 


y Select the icon to switch between
capitalized and lower-case characters.
 


y Select the icon to return to the
previous screen without storing the edit.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC