lock MAZDA MODEL CX-9 2017 Owners Manual (in English)

6–50
Maintenance and Care
Owner Maintenance
Rear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the screws counterclockwise and
remove them.


4. Pull the unit rearward to remove it.



5. Disconnect the wiring harness by
releasing the clamp.



6. Turn the socket and bulb assembly
counterclockwise and remove it.



CX-9_8FS7-EA-16K_Edition2.indb 50CX-9_8FS7-EA-16K_Edition2.indb 502016/12/15 18:36:142016/12/15 18:36:14

6–52
Maintenance and Care
Owner Maintenance
Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.



4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a fl athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
fl athead screwdriver.
3. Disconnect the bulb by pulling it out.



4. Install the new bulb in the reverse order
of the removal procedure.

CX-9_8FS7-EA-16K_Edition2.indb 52CX-9_8FS7-EA-16K_Edition2.indb 522016/12/15 18:36:152016/12/15 18:36:15

6–56
Maintenance and Care
Owner Maintenance
Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.

If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, fi rst
inspect the fuses on the vehicle's left side.


1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.

3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.


4. Inspect the fuse and replace it if it is
blown.

NormalBlown

5. Insert a new fuse of the same amperage
rating, and make sure it fi ts tightly. If
it does not fi t tightly, have an expert
install it. We recommend an Authorized
Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage
the electric system.

CX-9_8FS7-EA-16K_Edition2.indb 56CX-9_8FS7-EA-16K_Edition2.indb 562016/12/15 18:36:172016/12/15 18:36:17

6–57
Maintenance and Care
Owner Maintenance
6. Reinstall the cover and make sure that
it is securely installed.

Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:


1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.


3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating .

Normal
Blown

WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse
is a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fi re.

4. Reinstall the cover and make sure that
it is securely installed.

CX-9_8FS7-EA-16K_Edition2.indb 57CX-9_8FS7-EA-16K_Edition2.indb 572016/12/15 18:36:172016/12/15 18:36:17

6–58
Maintenance and Care
Owner Maintenance
*Some models.
Fuse Panel Description
Fuse block (Engine compartment)



DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 WIPER.DEI 20 A —
2 IG2 30 A For protection of various circuits
3 INJECTOR 30 A Engine control system
4 — — —
5 P.WINDOW1 30 A Power windows
*
6 — — —
7 — — —
8 EVVT 20 A Engine control system
9 DEFOG 40 A Rear window defogger
10 — — —
11 R.HEATER 40 A Air conditioner
12 EPB L 20 A Electric parking brake (EPB) (LH)
13 AUDIO 40 A Audio system
14 EPB R 20 A Electric parking brake (EPB) (RH)
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17



50 A For protection of various circuits
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
CX-9_8FS7-EA-16K_Edition2.indb 58CX-9_8FS7-EA-16K_Edition2.indb 582016/12/15 18:36:182016/12/15 18:36:18

6–60
Maintenance and Care
Owner Maintenance
*Some models.
Fuse block (Left side)



DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 P.SEAT D 30 A Power seat
*
2 P.WINDOW3 30 A Power windows *
3 R.OUTLET3 15 A Accessory sockets
4 P.WINDOW2 25 A Power windows
5 PLG 20 A Power liftgate
6 D.LOCK 25 A Power door locks
7 SEAT WARM 20 A Seat warmer
8 SRS2/ESCL 15 A —
9 SUNROOF 10 A Moonroof
10 INTERIOR2 15 A Audio system
11

7.5 A Engine control system
12 MIRROR 7.5 A Power control mirror
13 AT IND 7.5 A AT shift indicator
14 F.OUTLET 15 A Accessory sockets
15 R.OUTLET1 15 A —
16 — — —
17 M.DEF 7.5 A Mirror defogger
CX-9_8FS7-EA-16K_Edition2.indb 60CX-9_8FS7-EA-16K_Edition2.indb 602016/12/15 18:36:192016/12/15 18:36:19

7–5
If Trouble Arises
Flat Tire
NOTE
When inserting the luggage mat, support
the luggage board with one hand so that it
does not come off the holders.

5. Remove the cover on the right side.


Cover

6. Remove the cargo sub compartment.


Cargo sub compartment

7. Turn the wing bolt and jack screw
counterclockwise.


Wing boltJack screw
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing back and turn
the wing bolt clockwise to temporarily
tighten it.
2. Tighten the jack screw clockwise.


Wing boltJack screw
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.

CX-9_8FS7-EA-16K_Edition2.indb 5CX-9_8FS7-EA-16K_Edition2.indb 52016/12/15 18:36:262016/12/15 18:36:26

7–8
If Trouble Arises
Flat Tire
NOTE
When inserting the luggage mat, support
the luggage board with one hand so that it
does not come off the holders.

5. Remove the tool bag.
6. (Vehicles with sub-woofer)
Disconnect the sub-woofer connector.

Connector
7. (Vehicles with sub-woofer)
Turn the hold-down bolt
counterclockwise and remove the sub-
woofer and the spare tire.



(Vehicles without sub-woofer)
Turn the hold-down bolt
counterclockwise and remove the spare
tire.



CX-9_8FS7-EA-16K_Edition2.indb 8CX-9_8FS7-EA-16K_Edition2.indb 82016/12/15 18:36:282016/12/15 18:36:28

7–10
If Trouble Arises
Flat Tire
3. Turn on the hazard warning fl asher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffi c.
5. Remove the jack, tool, and spare tire
(page 7-3 ).
6. Block the wheel diagonally opposite
the fl at tire. When blocking a wheel,
place a tire block both in front and
behind the tire.


NOTE
When blocking a tire, use rocks or wood
blocks of suffi cient size if possible to hold
the tire in place.

Removing a Flat Tire
WARNING
When jacking-up a vehicle, always shift
the selector lever to P, apply the parking
brake, and place wheel blocks in the
position diagonally opposed to the jack:
Changing a fl at tire without using
wheel blocks is dangerous because the
vehicle may move and fall off the jack
even with the select lever is in P, which
could result in an accident.

1. Loosen the lug nuts by turning them
counterclockwise one turn each, but do
not remove any lug nuts until the tire
has been raised off the ground.



2. Place the jack on the ground.
3. Turn the jack screw in the direction
shown in the fi gure and adjust the jack
head so that it is close to the jack-up
position.


Jack head

CX-9_8FS7-EA-16K_Edition2.indb 10CX-9_8FS7-EA-16K_Edition2.indb 102016/12/15 18:36:292016/12/15 18:36:29

7–11
If Trouble Arises
Flat Tire
4. Set the jack to the designated jack-
up position closest to the tire being
removed.
(Jacking-up the vehicle front)
Set the groove on the top of the jack
head at a right angle into the center of
the designated jack-up position guide
projection closest to the vehicle front.


Jacking
position
Jacking head
Guide
projection

NOTE
Always set the jack into the designated
jack-up position shown in the fi gure
correctly.

(Jacking-up the vehicle rear)
Set the groove on the top of the jack
head at a right angle between the
designated jack-up position guide
projections.


Jacking
position
Jacking head
5. Continue raising the jack head
gradually by rotating the screw with
your hand until the jack head is inserted
into the jack-up position.


Tire blocks
Jacking position

CX-9_8FS7-EA-16K_Edition2.indb 11CX-9_8FS7-EA-16K_Edition2.indb 112016/12/15 18:36:292016/12/15 18:36:29