MAZDA MODEL CX-9 2017 Owners Manual (in English)

6–49
Maintenance and Care
Owner Maintenance
4. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.


Removal
Installation

5. Disconnect the wiring harness by
releasing the clamp.



6. Turn the socket and bulb assembly
counterclockwise and remove it. 7. Disconnect the bulb from the socket.

Front turn signal lights



Parking lights/Front side-marker
lights



8. Install the new bulb in the reverse order
of the removal procedure.
NOTE
There will be no problem with
functionality with the wiring harness
disconnected in Step 5 left disconnected.
Therefore, there is no need to connect the
wiring harness.

CX-9_8FS7-EA-16K_Edition2.indb 49CX-9_8FS7-EA-16K_Edition2.indb 492016/12/15 18:36:132016/12/15 18:36:13

6–50
Maintenance and Care
Owner Maintenance
Rear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the screws counterclockwise and
remove them.


4. Pull the unit rearward to remove it.



5. Disconnect the wiring harness by
releasing the clamp.



6. Turn the socket and bulb assembly
counterclockwise and remove it.



CX-9_8FS7-EA-16K_Edition2.indb 50CX-9_8FS7-EA-16K_Edition2.indb 502016/12/15 18:36:142016/12/15 18:36:14

6–51
Maintenance and Care
Owner Maintenance
7. Temporarily install the light unit with
the socket pulled out of the top of the
light unit.


Socket pull-out range

CAUTION
 


 The wiring harness may be damaged
when temporarily installing the light
unit. When performing the procedure,
observe the following points.
 


 Pull out the socket from within the
socket pull-out range shown in the
fi gure.
 


 Do not push the light unit into the
vehicle with force.
 


 When temporarily installing the light
unit, cover the rear bumper light unit
installation surface with a soft cloth.
The rear bumper may be scratched or
damaged if the light unit contacts it.

8. Disconnect the bulb from the socket.



9. Install the new bulb in the reverse order
of the removal procedure.

CX-9_8FS7-EA-16K_Edition2.indb 51CX-9_8FS7-EA-16K_Edition2.indb 512016/12/15 18:36:142016/12/15 18:36:14

6–52
Maintenance and Care
Owner Maintenance
Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.



4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a fl athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
fl athead screwdriver.
3. Disconnect the bulb by pulling it out.



4. Install the new bulb in the reverse order
of the removal procedure.

CX-9_8FS7-EA-16K_Edition2.indb 52CX-9_8FS7-EA-16K_Edition2.indb 522016/12/15 18:36:152016/12/15 18:36:15

6–53
Maintenance and Care
Owner Maintenance
*Some models.
Replacing Interior Light Bulbs
Overhead lights (Front)/Map lights
(Front) (LED type), Map lights (Center)
(LED type), Overhead lights (Rear)
(LED type), Ambient lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Overhead lights (Front)/Map lights
(Front) (bulb type), Map lights (Center)
(bulb type), Overhead light (Rear) (bulb
type), Vanity mirror lights
*
1. Wrap a small fl athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the fl athead screwdriver. 2. Disconnect the bulb by pulling it out.
Overhead lights (Front)/Map lights
(Front)





CX-9_8FS7-EA-16K_Edition2.indb 53CX-9_8FS7-EA-16K_Edition2.indb 532016/12/15 18:36:152016/12/15 18:36:15

6–54
Maintenance and Care
Owner Maintenance
*Some models.
Map lights (Center)


Forward




Overhead light (Rear)


Edge Forward
Vanity mirror lights
*




3. Install the new bulb in the reverse order
of the removal procedure.

CX-9_8FS7-EA-16K_Edition2.indb 54CX-9_8FS7-EA-16K_Edition2.indb 542016/12/15 18:36:162016/12/15 18:36:16

6–55
Maintenance and Care
Owner Maintenance
Luggage compartment light
(LED type)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
(Bulb type)

1. Wrap a small fl athead screwdriver
with a soft cloth to prevent damage to
the lens and remove the lens unit by
carefully prying on the edge of the lens
unit with the fl athead screwdriver.



2. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.



CAUTION
When replacing the bulb always
disconnect the connector fi rst.
Otherwise, electric and electronic
devices could be shorted.

3. Insert the fl athead screwdriver into the
gap between the lens and the lens unit,
and then slide the screwdriver to detach
the lens.



4. Disconnect the bulb by pulling it out.



5. Install the new bulb in the reverse order
of the removal procedure.

CX-9_8FS7-EA-16K_Edition2.indb 55CX-9_8FS7-EA-16K_Edition2.indb 552016/12/15 18:36:162016/12/15 18:36:16

6–56
Maintenance and Care
Owner Maintenance
Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.

If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, fi rst
inspect the fuses on the vehicle's left side.


1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.

3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.


4. Inspect the fuse and replace it if it is
blown.

NormalBlown

5. Insert a new fuse of the same amperage
rating, and make sure it fi ts tightly. If
it does not fi t tightly, have an expert
install it. We recommend an Authorized
Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage
the electric system.

CX-9_8FS7-EA-16K_Edition2.indb 56CX-9_8FS7-EA-16K_Edition2.indb 562016/12/15 18:36:172016/12/15 18:36:17

6–57
Maintenance and Care
Owner Maintenance
6. Reinstall the cover and make sure that
it is securely installed.

Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:


1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.


3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating .

Normal
Blown

WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse
is a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fi re.

4. Reinstall the cover and make sure that
it is securely installed.

CX-9_8FS7-EA-16K_Edition2.indb 57CX-9_8FS7-EA-16K_Edition2.indb 572016/12/15 18:36:172016/12/15 18:36:17

6–58
Maintenance and Care
Owner Maintenance
*Some models.
Fuse Panel Description
Fuse block (Engine compartment)



DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 WIPER.DEI 20 A —
2 IG2 30 A For protection of various circuits
3 INJECTOR 30 A Engine control system
4 — — —
5 P.WINDOW1 30 A Power windows
*
6 — — —
7 — — —
8 EVVT 20 A Engine control system
9 DEFOG 40 A Rear window defogger
10 — — —
11 R.HEATER 40 A Air conditioner
12 EPB L 20 A Electric parking brake (EPB) (LH)
13 AUDIO 40 A Audio system
14 EPB R 20 A Electric parking brake (EPB) (RH)
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17



50 A For protection of various circuits
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
CX-9_8FS7-EA-16K_Edition2.indb 58CX-9_8FS7-EA-16K_Edition2.indb 582016/12/15 18:36:182016/12/15 18:36:18