lock MAZDA MODEL MPV 2004 Owners Manual (in English)

8-22
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.

Replacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm. •Don’t bend the stiffeners. You need
to use them again.
•If the metal stiffeners are switched,
the blade’s wiping efficiency could
be reduced.
So don’t use the driver’s side metal
stiffeners on the passenger’s side, or
vice versa.
•Be sure to reinstall the metal
stiffeners in the new blade rubber so
that the curve is the same as it was
in the old blade rubber.
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
CAUTION
Ta b
To prevent damage to the wiper arm
and other components, don’t move the
wiper by hand.
To prevent damage to the rear window,
don’t let the wiper arm fall on it.
CAUTION
Push
Plastic locking clip
CAUTION
J16R_8S06-EA-03H_Edition1.book Page 22 Wednesday, July 9, 2003 4:19 PM

8-33
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
7. Carefully remove the headlight bulb
from the socket by pulling it straight
back.
8. Replace the bulb.
9. Install the new bulb in the reverse order
of removal.
Replacing a fog light bulb*
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.2. If a retaining spring is equipped, swing
it outward.
3. Disconnect the socket from the
electrical connector by pressing the tab
on the connector with your finger.
4. Turn the bulb counterclockwise and
remove it. Carefully remove the fog
light bulb from its socket by pulling it
straight back.
5. Install the new bulb in the reverse order
of removal.
NOTE
•Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
•When reinstalling the sealing cover,
make sure faces up.
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 33 Wednesday, July 9, 2003 4:19 PM

8-34
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
Front turn signal lights/Front side-
marker lights
1. Turn the screw counterclockwise and
remove it.
2. Turn the center section of the plastic
retainer counterclockwise and remove
it, then partially peel back the
mudguard.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse order
of removal.Side turn signal lights
1. Slide the unit as shown in the figure to
remove it.
2. Detach the electrical connector from
the unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.
Parking lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Screw
Removal
Installation
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
J16R_8S06-EA-03H_Edition1.book Page 34 Wednesday, July 9, 2003 4:19 PM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Taillights/Rear-
side marker lights
1. Remove the bolts with a Phillips
screwdriver and remove the rear
combination component.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.High-mount brake lights
1. Remove the liftgate upper trim.
2. Push the tab as shown in the figure, and
then remove the high-mount brake
light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
Brake lights/Taillights
Rear turn signal lights
Reverse lights
Taillights/Rear side-marker lights
J16R_8S06-EA-03H_Edition1.book Page 35 Wednesday, July 9, 2003 4:19 PM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
License plate lights
1. Slide the unit as shown in the figure to
remove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.

Replacing Interior Light Bulbs
Overhead light/Map lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
NOTE
An unsecured high-mount brake light
will allow water to leak into the
vehicle. Make sure the high-mount
brake light is tightly fastened to the
vehicle and if water still leaks, consult
an Authorized Mazda Dealer.
Edge
Without sunroof, with overhead console
Edge
Without either sunroof or overhead
console
J16R_8S06-EA-03H_Edition1.book Page 36 Wednesday, July 9, 2003 4:19 PM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it’s blown.
5. Push in a new fuse of the same rating,
and make sure it fits tightly. If it
doesn’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO circuit.If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
one of the same rating
.
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Fuse puller
Normal Blown
CAUTIONNOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-40).
Fuse block cover
Ta b
Normal Blown
J16R_8S06-EA-03H_Edition1.book Page 39 Wednesday, July 9, 2003 4:19 PM

8-40
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H

Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP, HAZARD,
ROOM, D.LOCK
and DRL fuses
3 ABS 60AAntilock brake
system
*, For
protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30ARear heater
*, For
protection of
various circuits
8 IG KEY2 40AA/C, P.WIND*,
MOONROOF*an
d R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuits
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
10 TAIL 15A Taillights
11
AC PW R15A Inverter
12HORN15A Horn
13
FOG 15AFor protection of
various circuits
14
EEC 5AFor protection of
various circuits
15
HEAD L 15AHeadlight-left
16HEAD R 15AHeadlight-right
17HID L 20A—
18HID R 20A—
19 IG KEY1 60AMETER,
ENGINE and
WIPER fuses
20 EGI INJ 30AFor protection of
various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120AFor protection of
all circuits
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 40 Wednesday, July 9, 2003 4:19 PM

8-41
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
Fuse block (Driver’s side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1
P. W I N D30APower windows*,
For protection of
various circuits
2
WIPER20AWindshield
wipers and
washer
3 SUN ROOF 15AMoonroof*, For
protection of
various circuits
4
R.WIP10ARear window
wiper and washer
5
SEAT20AFor protection of
various circuits
6
M.DEF10AMirror defroster*,
For protection of
various circuits
7
A/C10AAir conditioner,
For protection of
various circuits
8
DRL10AFor protection of
various circuits
9
———
10
H/CLEAN20AFor protection of
various circuits
11—— —
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
12 HAZARD 10AHazard warning
flashers
13 ROOM 15AOverhead lights,
Map lights,
Luggage
compartment light
14
AUX
POWER25A Accessory socket
15
CLOSER
LH20AFor protection of
various circuits
16
AUDIO10AAudio system, For
protection of
various circuits
17
D.LOCK30APower door
locks*, For
protection of
various circuits
18
P/SEAT30A
Power seat*
19ENGINE10AEngine control
system
20
METER10A Instrument cluster
21
STOP15A Brake lights
22
CLOSER
RH20AFor protection of
various circuits
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 41 Wednesday, July 9, 2003 4:19 PM

11-2
Form No. 8S06-EA-03H
Index
A
Accessory Socket ............................. 6-52
Add-On Non-Genuine Parts and
Accessories
...................................... 9-13
Air Bag Systems
.............................. 2-56
Air Filter
.......................................... 8-19
Antenna
............................................ 6-14
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-43
Ashtray
............................................. 6-45
Audio System
................................... 6-14
Audio control switch
................ 6-38
Audio set
................................... 6-21
Operating tips for
audio system
............................. 6-14
Safety certification
.................... 6-40
Automatic Transaxle
Driving tips
............................... 5-13
Fluid
.......................................... 8-16
Overdrive
.................................. 5-12
Shift-lock override
.................... 5-12
Shift-lock system
...................... 5-11
Transaxle ranges
....................... 5-10
B
Battery
Emergency starting
................... 7-17
Maintenance
............................. 8-24
Specifications
........................... 10-4
Beep Sounds
Ignition key reminder
............... 5-33
Lights-on reminder
................... 5-33
Power sliding door beep
........... 5-33
Seat belt warning beep
.............. 5-33
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
B
Body Lubrication ............................. 8-19
Bottle Holder
.................................... 6-48
Brake
Fluid
.......................................... 8-15
Brakes
Anti-lock brake system (ABS)
....5-7
Foot brake
................................... 5-4
Pad wear indicator
...................... 5-8
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-31
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Cargo Securing Loops
...................... 6-51
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-14
Child Restraint
Child restraint precautions
........ 2-41
Installing child-restraint
systems
...................................... 2-45
LATCH child-restraint
systems
...................................... 2-53
Child Safety Locks for Rear
Doors
................................................ 3-12
Cigarette Lighter
.............................. 6-44
Climate Control System
.....................6-2
Gas specifications
..................... 10-5
Courtesy Lights
................................ 6-44
Cruise Control
.................................. 5-14
Cup Holder
....................................... 6-46
Customer Assistance
.......................... 9-2
J16R_8S06-EA-03H_Edition1.book Page 2 Wednesday, July 9, 2003 4:19 PM

11-3
Index
Form No. 8S06-EA-03H
D
Dashboard Illumination ................... 5-23
Daytime Running Lights
.................. 5-35
Defroster
Rear window
............................. 5-38
Dimensions
...................................... 10-5
Door Locks
......................................... 3-8
Driving In Flooded Area
.................. 4-11
Driving Tips
....................................... 4-7
Automatic transaxle
.................. 5-13
Break-in period
........................... 4-7
Driving in flooded area
............. 4-11
Hazardous driving
....................... 4-8
Money-saving suggestions
.......... 4-7
Rocking the vehicle
.................... 4-9
Winter driving
............................. 4-9
E
Easy Closure .................................... 3-12
Emergency Starting
.......................... 7-17
Flooded engine
.......................... 7-17
Jump-starting
............................ 7-18
Push-starting
............................. 7-21
Emergency Towing
.......................... 7-22
Emission Control System
................... 4-3
Engine
Coolant
...................................... 8-12
Exhaust gas
................................. 4-5
Hood release
............................. 3-24
Oil
............................................. 8-10
Overheating
............................... 7-15
Starting
........................................ 5-3
Engine Compartment Overview
........ 8-9
Engine Coolant
Overheating
............................... 7-15
Engine Coolant Temperature
Gauge
............................................... 5-22
Exhaust Gas
....................................... 4-5
E
Exterior Care ....................................8-45
Eyeglass Holder
................................6-49
F
Flasher
Hazard warning
.........................5-39
Headlights
.................................5-34
Flat Tire
..............................................7-3
Changing
.....................................7-8
Spare tire and tool storage
...........7-3
Fluids
Classification
.............................10-4
Owner maintenance
.....................8-7
Fog Lights
........................................5-36
Foot Brake
..........................................5-4
Front Console
...................................6-50
Front Seats
(Electrically Operated Seats)
..............2-8
Front Seats
(Manually Operated Seats)
.................2-3
Fuel
Filler lid and cap
.......................3-23
Gauge
........................................5-23
Requirements
..............................4-2
Tank capacity
............................10-5
Fuses
.................................................8-38
Panel description
.......................8-40
Replacement
..............................8-38
G
Gauges ..............................................5-20
Glove Box
........................................6-50
J16R_8S06-EA-03H_Edition1.book Page 3 Wednesday, July 9, 2003 4:19 PM