clock MAZDA MODEL MPV 2004 (in English) Owner's Manual

8-33
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
7. Carefully remove the headlight bulb
from the socket by pulling it straight
back.
8. Replace the bulb.
9. Install the new bulb in the reverse order
of removal.
Replacing a fog light bulb*
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.2. If a retaining spring is equipped, swing
it outward.
3. Disconnect the socket from the
electrical connector by pressing the tab
on the connector with your finger.
4. Turn the bulb counterclockwise and
remove it. Carefully remove the fog
light bulb from its socket by pulling it
straight back.
5. Install the new bulb in the reverse order
of removal.
NOTE
•Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
•When reinstalling the sealing cover,
make sure faces up.
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 33 Wednesday, July 9, 2003 4:19 PM

8-34
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
Front turn signal lights/Front side-
marker lights
1. Turn the screw counterclockwise and
remove it.
2. Turn the center section of the plastic
retainer counterclockwise and remove
it, then partially peel back the
mudguard.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse order
of removal.Side turn signal lights
1. Slide the unit as shown in the figure to
remove it.
2. Detach the electrical connector from
the unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.
Parking lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Screw
Removal
Installation
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
J16R_8S06-EA-03H_Edition1.book Page 34 Wednesday, July 9, 2003 4:19 PM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Taillights/Rear-
side marker lights
1. Remove the bolts with a Phillips
screwdriver and remove the rear
combination component.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.High-mount brake lights
1. Remove the liftgate upper trim.
2. Push the tab as shown in the figure, and
then remove the high-mount brake
light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
Brake lights/Taillights
Rear turn signal lights
Reverse lights
Taillights/Rear side-marker lights
J16R_8S06-EA-03H_Edition1.book Page 35 Wednesday, July 9, 2003 4:19 PM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8S06-EA-03H
License plate lights
1. Slide the unit as shown in the figure to
remove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.

Replacing Interior Light Bulbs
Overhead light/Map lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
NOTE
An unsecured high-mount brake light
will allow water to leak into the
vehicle. Make sure the high-mount
brake light is tightly fastened to the
vehicle and if water still leaks, consult
an Authorized Mazda Dealer.
Edge
Without sunroof, with overhead console
Edge
Without either sunroof or overhead
console
J16R_8S06-EA-03H_Edition1.book Page 36 Wednesday, July 9, 2003 4:19 PM