remove seats MAZDA MODEL MPV 2005 (in English) User Guide

Black plate (33,1)
WARNING
Unlocked Seatback:
The seatback plays an important role
in your protection in a vehicle.
Leaving the seatback unlocked is
dangerous as it can allow passengers
to be ejected or thrown around and
baggage to strike occupants in a
sudden stop or collision, resulting in
severe injury. After adjusting the
seatback at any time, even when there
are no other passengers, rock the
seatback to make sure it is locked in
place.
Passenger on the Folded Seatback:
Driving with a passenger on the folded
seatback is dangerous. Allowing a
child to sit up on the folded seatback
while the vehicle is moving is
particularly dangerous. In a sudden
stop or even a minor collision, a child
not in a proper seat or child-restraint
system and seat belt could be thrown
forward, back or even out of the
vehicle resulting in serious injuries or
death. The child or other objects in the
baggage area could be thrown into
other occupants and cause serious
injury. Never allow a passenger to sit
or stand on the folded seatback while
the vehicle is moving.
NOTE
lThe third-row seat cannot be
removed.
lWhen returning the third-row seat to
its original position, also place the
seat belt in its normal position.
Verify that the seat belt pulls and
retracts.
qSeat Recline
WARNING
Reclining:
Sitting in a reclined position while the
vehicle is moving is dangerous
because you don't get the full
protection from seat belts. During
sudden braking or a collision, you can
slide under the lap belt and suffer
serious internal injuries. For
maximum protection, sit well back and
upright.
To change seatback angle, lean forward
slightly while pulling the flat-folding
strap. Then lean back to the desired
position and release the strap. Make sure
the seat is securely latched.
Essential Safety Equipment
Seats
2-21
Mazda MPV_8T50-EA-04G_Edition1 Page33
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (34,1)
qHead Restraint
WARNING
Head Restraints Adjustment:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be
seriously injured in a collision. Always
drive with the head restraints inserted
when seats are being used and make
sure they are properly adjusted.
Height adjustment
To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.
Adjust the head restraint so that the top is
parallel with the top of the passenger's
ears, never the passenger's neck.
Removal
To remove the head restraint, press the
stop-catch release, then pull up on the
head restraint.
qFolding the Third-Row Seat
WARNING
Riding on Folded Flat Third-Row
Seat:
Riding on the third-row seat when it's
folded is dangerous. During sudden
braking or a collision, passenger's
could be thrown around inside the
vehicle and seriously injured. Always
ride with the third-row seat in the
forward-facing, upright position and
seat belt securely fastened.
2-22
Essential Safety Equipment
Seats
Mazda MPV_8T50-EA-04G_Edition1 Page34
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (35,1)
1. Remove the head restraints from the
third-row seat (page 2-22).
2. Pull the third-row seat's flat-folding
strap and push the seatback down until
it locks.
qStowing the Third-Row Seat
More storage space can be created by
folding away the third-row seat into the
rear seat well. With the second-row seats
removed and the third-row seat stowed,
even more space is available.
WARNING
Riding in the Seat Well:
Riding in the seat well for the third-
row seat is dangerous. Sudden
braking or a collision could cause
serious injury. Do not sit or lie in the
seat well while the vehicle is moving.
Never ride in a vehicle where you
can't sit in the seat and wear the seat
belt.
WARNING
Pinching Fingers or Hands:
Placing your hands around the seat
stowage well when stowing the third-
row seat is dangerous. You could
pinch your hands or fingers between
the seat and the well. Hold the handle
when lowering the seat into place.
Never place your hands between the
seat and the seat well.
Unlocked Seatback:
An unlocked seatback is dangerous.
While stowing the seat, the seatback
could suddenly move causing serious
injury. Push the seatback forward and
backward to make sure it is locked in
place.
NOTE
Remove any items from the seat well
for the third-row seat before stowing the
seat. Anything in the baggage area
when the seat is set into the well can
damage the seatback material and
prevent a flat cargo area.
Essential Safety Equipment
Seats
2-23
Mazda MPV_8T50-EA-04G_Edition1 Page35
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (36,1)
Stowing the third-row seat
1. Insert the seat belts in the retainers.
2. Remove the head restraint and set them
aside temporarily (page 2-22).
3. Pull strap A and ease the seatback
toward the front of the vehicle with
your other hand and be sure it locks
with a click.
Strap A
4. Pull strap B and lift the combined
seatback and seat bottom up to vertical
with your other hand. Gently lower the
seat into the seat well.
Strap B
5. Insert the head restraints between the
floor and seat at the positions indicated
on the labels.
Labels
Raising the third-row seat upright for
road use
1. Clear the entire cargo floor.
2-24
Essential Safety Equipment
Seats
Mazda MPV_8T50-EA-04G_Edition1 Page36
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (37,1)
2. Remove the head restraints.
3. Carefully reverse the procedures used
to lower the seat into the seat well. Use
the handle and ease the combined
seatback and seat bottom up to vertical.
4. Carefully lower the seat forward and
make sure it's latched to the floor.
5. Pull strap A and raise the seatback
upright. Attempt to move the seatback
forward and backward to make sure it
is locked.
Strap A
6. Insert the head restraints.
7. Place the seat belt buckles face up.
Essential Safety Equipment
Seats
2-25
Mazda MPV_8T50-EA-04G_Edition1 Page37
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (38,1)
qThird-Row Seat and Open
Liftgate Position
WARNING
Rear Facing Third-Row Seat and a
Moving Vehicle:
Driving with the third-row seat facing
rearward is dangerous because the
liftgate cannot be securely closed.
During sudden braking or a collision,
passengers could be thrown out of the
vehicle resulting in serious injury or
death. Passengers seated facing
rearward may suffer leg and foot
injury even down a driveway or with a
minor dip in the road. Place the third-
row seat in the forward-facing position
with the seatback upright before
driving the vehicle.
Support Bar:
Sitting in the rear-facing, third-row
seat position without installing the
support bar is dangerous. Without the
support of the bar, the seatback could
collapse resulting in injury.
Always install the support bar before
sitting in the rear-facing, third-row
seat position.
Third-Row Seat and the Flat-Folding
Strap:
Pulling the flat-folding strap with the
third-row seat facing rearward is
dangerous. The seatback will collapse
into the seat bottom and could result
in injury. Do not pull the flat-folding
strap with the third-row seat facing
rearward.
NOTE
lRemove cargo from the seat well
area before placing the third-row seat
in the rear-facing position to avoid
damaging the back of the seatback
when it is folded down.
lAdjust the seatback to the upright
position when the third-row seat is
facing rearward.
To put the third-row seat in the rear
facing position:
1. Open the liftgate.
2. Clean the rear bumper so that dirt does
not soil the seat.
3. Clear away all cargo from the seat well.
4. Remove the head restraints.
5. Pull strap B while supporting the
seatback with the other hand and
carefully ease the seatback rearward
onto the rear bumper.
Strap B
6. Go inside the vehicle and to the rear.
2-26
Essential Safety Equipment
Seats
Mazda MPV_8T50-EA-04G_Edition1 Page38
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (39,1)
7. Remove the support bar from the
pocket.
8. Set the hook on the support bar in the
rear of the seatback.
9. Pull the seatback towards the front of
the vehicle until the opposite end of the
support bar hooks onto the anchor loop
in the side trim. Attempt to push the
seatback towards the rear (liftgate) to
make sure the support bar is securely
latched.
To return the third-row seat to the road
position (forward facing)
1. Make sure to stow the shoulder belts
away from the seat bottom as it is
lowered.
2. Detach the support bar by following
the reverse procedure for installation.
Essential Safety Equipment
Seats
2-27
Mazda MPV_8T50-EA-04G_Edition1 Page39
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (40,1)
3. From inside the vehicle, carefully
lower the seat towards the front until it
locks in place. Attempt to move the
seat forward and backward to make
sure it's securely locked in place.
4. Reinsert the head restraints.
5. Place the seat belt buckles face up.
6. Fasten the shoulder belts and check
that they are routed properly for
passenger use.
Flat Folding
All seats can be folded down for use as
beds when the vehicle is safely parked.
WARNING
Folded-Flat Seats:
Sitting or lying on seats folded flat is a
dangerous way to ride. During sudden
braking or a collision you could be
thrown around inside the vehicle and
seriously injured. Don't ride on
seatbacks folded flat.
qTo Fold the Seats Flat
1. Slide the second-row seat all the way
back (page 2-13).
2. Fold down the second-row seatbacks
rearward until they lock (page 2-14).
3. Remove the head restraints from the
front seats. Refer to Head Restraint
(Manually Operated Seats)(page 2-5).
Refer to Head Restraint (Electrically
Operated Seats)(page 2-10).
2-28
Essential Safety Equipment
Seats
Mazda MPV_8T50-EA-04G_Edition1 Page40
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (61,1)
2. To get the retractor into the automatic
locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
3. Push the child-restraint system firmly
into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in the
automatic locking mode. If the belt
does not lock the seat down tight,
repeat this step.
NOTE
Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt out
of the retractor while the system is in
the automatic locking mode. When you
remove the child-restraint system, be
sure the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
qIf You Must Use the Front Seat
for Children
If you cannot put all children in the rear
seats, at least put the smallest children in
the rear and be sure the largest child up
front uses the shoulder belt over the
shoulder.
Do not put rear-facing child-restraint
systems on the front passenger's seat.
This seat is also not set up for tethered
child-restraint systems, put them in one of
the rear seat positions set up with tether
anchors.
Likewise the LATCH child-restraint
system cannot be secured in the front
passenger's seat and should be used in the
second-row seats.
Don't allow anyone to sleep against the
right front or rear doors if you have an
optional side air bag, it could cause
serious injuries to an out of position
occupant. As children more often sleep in
cars, it is better to put them in the rear
seat. If installing the child-restraint system
on the front seat is unavoidable, follow
these instructions when using a front-
facing child-restraint system in the front
passenger's seat.
Essential Safety Equipment
Child Restraint
2-49
Mazda MPV_8T50-EA-04G_Edition1 Page61
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G

Black plate (65,1)
LATCH Child-Restraint Systems
Your Mazda is equipped with LATCH lower anchors for attachment of specially designed
LATCH child-restraint systems in the second-row seats. Both anchors must be used,
otherwise the seat will bounce around and put the child in danger. Some LATCH child-
restraint systems must also be used in conjunction with a tether to be effective. If they have
a tether you must use it to better assure your child's safety.
WARNING
Manufacturer's Instructions for Child-Restraint System:
An unsecured child-restraint system is dangerous. In a sudden stop or a collision it
could move causing serious injury or death to the child or other occupants. Make sure
the child-restraint system is properly secured in place according to the child-restraint
system manufacturer's instructions.
Unsecured Child-Restraint System:
An unsecured child-restraint system is dangerous. In a sudden stop or a collision it
could move causing serious injury or death to the child or other occupants. Follow the
child-restraint system manufacturer's instructions on belt routing to secure the seat
just as you would with a child in it so that nobody is tempted to put a child in an
improperly secured seat later on. When not in use, remove it from the vehicle or fasten
it with a seat belt, or latch it down to BOTH LATCH lower anchors for LATCH child-
restraint systems.
LATCH Child-Restraint Systems:
Not following the child-restraint system manufacturer's instructions when installing
the child-restraint system is dangerous. If seat belts or a foreign object prevent the
child-restraint system from being securely attached to the LATCH lower anchors and
the child-restraint system is installed improperly, the child-restraint system could move
in a sudden stop or collision causing serious injury or death to the child or other
occupants. When installing the child-restraint system, make sure there are no seat
belts or foreign objects near or around the LATCH lower anchors. Always follow the
child-restraint system manufacturer's instructions.
Essential Safety Equipment
Child Restraint
2-53
Mazda MPV_8T50-EA-04G_Edition1 Page65
Monday, June 28 2004 3:59 PM
Form No.8T50-EA-04G