length MAZDA MODEL MPV 2006 Owners Manual (in English)

Black plate (44,1)
qEmergency Locking Mode
In the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision. When the seat belt is retracted, it will
always be in the emergency locking mode until it is switched to automatic locking mode by
pulling it all the way out to its full length. If the belt feels tight and hinders comfortable
movement while the vehicle is stopped or in motion, it may be in the automatic locking
mode because the belt has been pulled too far out. To return to the belt more comfortable
emergency locking mode, wait until the vehicle has stopped in a safe, level area, retract the
belt fully to convert it back to emergency locking mode and then extend it around you
again.
qAutomatic Locking Mode
Always use the automatic locking mode to keep the child-restraint system from shifting to
an unsafe position in the event of an accident. To enable seat belt automatic locking mode,
pull it all the way out and connect it as instructed on the child-restraint system. It will
retract down to the child-restraint system and stay locked on it. See the section on child
restraint (page 2-41).
2-32
Essential Safety Equipment
Seat Belt Systems
Mazda MPV_8U61-EA-05G_Edition1 Page44
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (49,1)
Center, Third-Row
Position Seat Belt
qFastening the Seat Belt
1. Pull the tongue to the desired length.
2. Insert it into the buckle until you hear a
click.
Tongue
Buckle
3. Adjust the belt length.
To lengthen the belt, hold the tongue at
a right angle to the webbing and pull.
To shorten, pull the loose end of the
webbing.
Lengthen
Shorten
4. Make sure the lap belt is snugly fitted
against your body.
WARNING
Wearing the Lap Belt:
A lap belt worn too high is dangerous.
In a collision, this would concentrate
the impact force directly on the
abdominal area, causing serious
injury. Wear the lap belt snugly and as
low as possible.
Essential Safety Equipment
Seat Belt Systems
2-37
Mazda MPV_8U61-EA-05G_Edition1 Page49
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (50,1)
qUnfastening the Seat Belt
Depress the button on the buckle.
Button
Seat Belt Extender
If your seat belt is not long enough, even
when fully extended, a seat belt extender
may be available to you at no charge from
your Authorized Mazda Dealer.
This extender will be only for you and for
the particular vehicle and seat. Even if it
plugs into other seat belts, it may not hold
in the critical moment of a crash.
When ordering an extender, only order
one that provides the necessary additional
length to fasten the seat belt properly.
Please contact your Authorized Mazda
Dealer for more information.
WARNING
Unnecessary Use of an Extender:
Using a seat belt extender when not
necessary is dangerous. The seat belt
will be too long and not fit properly. In
an accident, the seat belt will not
provide adequate protection and you
could be seriously injured. Only use
the extender when it is required to
fasten the seat belt properly.
Using an Improper Extender:
Using a seat belt extender that is for
another person or a different vehicle
or seat is dangerous. The seat belt will
not provide adequate protection and
the user could be seriously injured in
an accident. Only use the extender
provided for you and for the particular
vehicle and seat. NEVER use the
extender in a different vehicle or seat.
2-38
Essential Safety Equipment
Seat Belt Systems
Mazda MPV_8U61-EA-05G_Edition1 Page50
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (51,1)
WARNING
Using an Extender That is Too Long:
Using an extender that is too long is
dangerous. The seat belt will not fit
properly. In an accident, the seat belt
will not provide adequate protection
and you could be seriously injured.
Don't use the extender or choose one
shorter in length if the distance
between the extender's buckle and the
center of the user's body is less than
15cm (6 in).
NOTE
When not in use, remove the seat belt
extender and store it in the vehicle. If
the seat belt extender is left connected,
the seat belt extender might get
damaged as it will not retract with the
rest of the seat belt and can easily fall
out of the door when not in use and be
damaged the seat belt warning light will
not illuminate and function properly.
Seat Belt Warning Light
If the driver's seat belt is not fastened
when the ignition switch is turned to the
ON position, the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.
Essential Safety Equipment
Seat Belt Systems
2-39
Mazda MPV_8U61-EA-05G_Edition1 Page51
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (58,1)
1. If the seat in which you install a child-
restraint system has a seat slide
function, slide the seat as far back as
possible.
2. Make sure the seatback is securely
latched by pushing it back until it is
fully locked.
3. Secure the child-restraint system with
the lap portion of the lap/shoulder belt.
See the manufacturer's instructions on
the child-restraint system for belt
routing instructions.
4. To get the retractor into the automatic
locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.5. Push the child-restraint system firmly
into the vehicle seat. Be sure the belt
retracts as snugly as possible. Adjust
the angle of the seat belt buckle so that
the belt is not loose. Clicking from the
retractor will be heard during retraction
if the system is in the automatic
locking mode. If the belt does not lock
the seat down tight, repeat this step.
NOTE
Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt out
of the retractor while the system is in
the automatic locking mode. When you
remove the child-restraint system, be
sure the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
6. If your child-restraint system requires
the use of a tether strap, hook and
tighten the tether strap after raising the
head restraint by following the
manufacturer's instructions.
2-46
Essential Safety Equipment
Child Restraint
Mazda MPV_8U61-EA-05G_Edition1 Page58
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (61,1)
2. To get the retractor into the automatic
locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
3. Push the child-restraint system firmly
into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in the
automatic locking mode. If the belt
does not lock the seat down tight,
repeat this step.
NOTE
Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt out
of the retractor while the system is in
the automatic locking mode. When you
remove the child-restraint system, be
sure the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
qIf You Must Use the Front Seat
for Children
If you cannot put all children in the rear
seats, at least put the smallest children in
the rear and be sure the largest child up
front uses the shoulder belt over the
shoulder.
NEVER put a rear-facing child-restraint
system on the front passenger seat, even
with a seat weight sensor equipped
vehicle.
This seat is also not set up for tethered
child-restraint systems, put them in one of
the rear seat positions set up with tether
anchors.
Likewise the LATCH child-restraint
system cannot be secured in the front
passenger's seat and should be used in the
second-row seats.
Don't allow anyone to sleep against the
side window if you have an optional side
air bag, it could cause serious injuries to
an out of position occupant. As children
more often sleep in cars, it is better to put
them in the rear seat. If installing the
child-restraint system on the front seat is
unavoidable, follow these instructions
when using a front-facing child-restraint
system in the front passenger's seat.
Essential Safety Equipment
Child Restraint
2-49
Mazda MPV_8U61-EA-05G_Edition1 Page61
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (63,1)
qFront Passenger's Seat Child-
Restraint System Installation
1. Slide the seat as far back as possible.
2. Secure the child-restraint system with
the lap portion of the lap/shoulder belt.
See the manufacturer's instructions on
the child-restraint system for belt
routing instructions.
3. To get the retractor into the automatic
locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmly
into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in automatic
locking mode. If the belt does not lock
the seat down tight, repeat the previous
step and also this one.
NOTE
lInspect this function before each use
of the child-restraint system. You
should not be able to pull the
shoulder belt out of the retractor
while the system is in the automatic
locking mode. When you remove the
child-restraint system, be sure the
belt fully retracts to return the system
to emergency locking mode before
occupants use the seat belts.
lFollow the child-restraint system
manufacturer's instructions carefully.
Depending on the type of child-
restraint system, it may not employ
seat belts which are in automatic
locking mode.
5. Make sure the front passenger air bag
deactivation indicator light illuminates
after installing a child-restraint system
on the front passenger seat.
Refer to Front passenger air bag
deactivation indicator light on page
2-63.
Essential Safety Equipment
Child Restraint
2-51
Mazda MPV_8U61-EA-05G_Edition1 Page63
Tuesday, June 21 2005 9:32 AM
Form No.8U61-EA-05G

Black plate (137,1)
qTrailer Towing Tips
lVerify that your Mazda maintains a near-normal attitude when a loaded or unloaded
trailer is connected. Don't drive if it has an abnormal front-up or front-down position.
Inspect for incorrect tongue load, worn suspension parts, and trailer overloading.
lMake sure the trailer is properly loaded and the cargo is secure to prevent it from
shifting.
lMake sure the mirrors conform to all government regulations. If they do not, install
required rear view mirrors appropriate for towing purposes.
The three main causes of vehicle-trailer accidents are driver error, excessive speed, and
improper trailer loading.
Before driving
lHave your cooling and braking system checked by an Authorized Mazda Dealer.
lBefore starting out, inspect the operation of all vehicle and trailer lights and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections after driving a short
distance.
Driving
lYour Mazda will handle differently with a trailer in tow, so practice turning, backing,
and stopping in a traffic-free area.
lTake time to get accustomed to the extra weight and length.
lAllow more room between your vehicle and the one in front because braking distance
increases with a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle
and trailer length between your Mazda and the vehicle ahead.
lAvoid jerky starts or sudden acceleration.
lAvoid sudden braking. It may cause loss of control and result in jackknifing, especially
so on wet or slippery roads.
lUse the following positions when towing a trailer in hilly terrain or when heavily
loaded.
lOD (overdrive) offlShift lever in D
These positions will allow operating the vehicle without frequent shifting.
Lane changes and turning
Avoid quick lane changes, sudden turns, and tight turns. Slow down before turning to
avoid the need of sudden braking.
A turning trailer will make a tighter arc than the tow vehicle. Compensate with turns that
are larger than normal.
Before Driving Your Mazda
Towing
4-17
Mazda MPV_8U61-EA-05G_Edition1 Page137
Tuesday, June 21 2005 9:33 AM
Form No.8U61-EA-05G

Black plate (355,1)
qDimensions
Item Model
Overall lengthWithout GFX Package 4,807 mm (189.3 in), 4,821 mm (189.8 in)*1
With GFX Package 4,813 mm (189.5 in), 4,833 mm (190.3 in)*1
Overall width 1,830 mm (72.1 in)
Overall height 1,745 mm (68.7 in), 1,755 mm (69.1 in)*2
Front tread 1,540 mm (60.6 in)
Rear tread 1,545 mm (60.8 in)*3, 1,550 mm (61.0 in)*4
Wheelbase 2,840 mm (111.8 in)
*1 With license plate holder
*2 17 inch wheel vehicle
*3 Rear drum brake
*4 Rear disc brake
qWeights
Item Weight
GVWR (Gross Vehicle Weight Rating) 2,386 kg (5,260 lb)
GAWR (Gross Axle Weight Rating)Front 1,189 kg (2,621 lb)
Rear 1,218 kg (2,685 lb)
qAir Conditioner
Refrigerant complies with SAE J639 Maximum operating charge
HFC134a (R-134a)Front air-conditioner 0.6 kg (21.2 oz)
Front and rear air-conditioner 0.8 kg (28.2 oz)
Specifications
10-5
Mazda MPV_8U61-EA-05G_Edition1 Page355
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G