instrument MAZDA MODEL MX-30 EV 2022 Owner's Guide

1. Shift position indication

When the power switch is switched
ON, the shift position is displayed in
the instrument cluster.
In the following cases, the shift
position is displayed in the instrument
cluster even if the power switch is in a
position other than ON.
The AUTO P (parking lock) function
is operating.
Neutral hold mode (automatic car
wash mode) is operating.
Shift guide indication
When the shift position and the
selector lever set position differ, the
shift position and the selector lever set
position are displayed.
1. Shift guide indication
2. Selector lever set position
3. Shift position

The shift guide indication is displayed
under the following conditions.
The selector lever is shifted to the P
position while driving (vehicle speed
of about 5 km/h (4 mph) or faster)
with the selector lever in the D
position.
The selector lever is shifted to the R
position while driving forward
(vehicle speed of about 10 km/h
(6.3 mph) or faster) with the selector
lever in the D position.
The selector lever is shifted to the D
position while driving in reverse
(vehicle speed of about 10 km/h
(6.3 mph) or faster) with the selector
lever in the R position.
The AUTO P (parking lock) function
is operating.
While neutral hold mode (automatic
car wash mode) is operating , the
selector lever is shifted from the N
position to the D or R position.
NOTE
In the following cases, the shift
position and the selector lever set
position di ffer, however, the shift
guide indication is not displayed.
The selector lever is shifted from
the N position to the D or R
position with the brake pedal not
depressed.
When the power switch is switched
ON or from ACC to OFF, the shift
guide indication displayed after
operating the AUTO P (parking lock)
function turns on for about 40
seconds and then it turns off.
When Driving
Selector Lever Position Functions
4-27
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Selector Lever Operation
▼Selector Lever Operation
Indication
Various Lockouts
Indicates that you must depress the brake pedal and hold in the lock-release
button to shift (The power switch must be switched ON).
Indicates the selector lever can be shifted freely into any position.
Indicates that you must hold in the lock-release button to shift.
WARNING
When operating the selector lever, shift the selector lever with the brake pedal
firmly depressed and the vehicle completely stopped:
If the selector lever is operated while the vehicle is moving, it could result in a
serious accident and injury.
NOTE
Prevention of mis-operation
When operating the selector lever, firmly shift to each shift position to prevent a
mis-operation. After the operation, check the shift position using the shift position
indication in the instrument cluster.
Depress the brake pedal before operating the selector lever
When shifting the selector lever from the P position, shifting may not be possible if
the brake pedal is depressed with the selector lever pressed. Depress the brake
pedal before operating the selector lever.
The AUTO P (parking lock) function
If the following operations are performed with the selector lever switched to a
position other than P while the vehicle is stopped, the shift position changes to the P
position automatically.
The power switch is switched from ON to OFF.
When Driving
Selector Lever Position Functions
4-28
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The driver’s seat belt is unfastened and the driver’s door is opened.
NOTE
When the AUTO P (parking lock) function operates, only the shift position changes
to the P position automatically. The shift po sition indication in the instrument cluster
will di ffer from the selector lever position because the selector lever position does
not change. Check the shift position indication in the instrument cluster and shift the
selector lever to the P position.
Neutral hold mode (autom atic car wash mode)
When in neutral hold mode (automatic car wash mode), a condition is maintained
for about 25 minutes in which the power switch is switched to ACC, the shift
position is in the N position, and the parking brake is released.
Use this mode when it is necessary to release the parking brake and change the shift
position to the N position, such as in an automatic car wash that moves the vehicle
by placing the front and rear tires on one side of the vehicle on a belt conveyor.
Operating neutral hold mode (automatic car wash mode)
Perform any of the following operations when the selector lever is in the N position
with the power switch switched ON (EV system on).
Operation method 1
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the Electric Parking Brake (EPB) switch continuously for 2 seconds or longer (until a sound is activated).
6. Release the EPB switch and press the pow er switch within 5 seconds after the
sound was activated.
Operation method 2
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the power switch with the EPB switch pressed and held while the brake
pedal is not depressed.
NOTE
When the selector lever is shifted from the N position to the D or R position while
neutral hold mode (automatic car wash mode) is operating , a message is displayed
on the multi-information display and the warning beep is activated.
Canceling neutral hold mode (automatic car wash mode)
If any of the following operations is performed, neutral hold mode (automatic car
wash mode) is canceled.
When Driving
Selector Lever Position Functions
4-29
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Shift-Lock System
▼Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

1. Depress and hold the brake pedal.
2. Press the power switch to start the
EV system.
3. Shift the selector lever while pressing the selector lever button.
NOTE
When the power switch is switched
OFF or to ACC, or ON (EV systemo ff), the selector lever cannot be
moved from the P position.
When canceling the shift-lock
system, switch the power switch ON
(EV system on) and shift the selector
lever with the brake pedal
depressed.
If the selector lever cannot be shifted
from the P position, the lead-acid
battery could be depleted.
Refer to Jump-Starting on page
7-12.
Driving Tips
▼ Driving Tips
When starting to drive the vehicle or
reversing the vehicle
WARNING
Do not shift the selector lever with the
accelerator pedal depressed when the
selector lever is in the P or N position:
Otherwise, the vehicle will suddenly
accelerate which could lead to an
accident. Shift the selector lever with
the brake pedal depressed.
1. Shift the selector lever with the
brake pedal depressed.
Forward: DReverse: R
2. Check the shift position indication in the instrument cluster.
3. Release the parking brake.
4. Gradually release the brake pedal and depress the accelerator pedal
to start driving the vehicle.
CAUTION
When visually checking at the rear of
the vehicle while reversing the vehicle,
your body twists around to the rear. Be
careful and make sure that the brake
pedal can be firmly depressed.
NOTE
When the shift position is in the R
position, the beep is activated to
notify the driver that the shift
position is in the R position.
When Driving
Selector Lever Position Functions
4-32
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

There is the possibility of forgetting
that the selector lever is shifted to
the R position when only reversing
the vehicle a little. After reversing the
vehicle, immediately shift the
selector lever to the N or P position,
and before starting to drive the
vehicle again, check the shift
position indication in the instrument
cluster.
When driving
WARNING
Do not shift the selector lever to the N
position while driving:
Decelerat ion using the regenerat ive
braking is not possible which could
result in an accident.
Normal driving
Shift the selector lever to the D
position to drive the vehicle.
Acceleration/deceleration is
performed using the accelerator and
brake pedals.
Driving on steep upslopes
Slowly depress the accelerator pedal to
adjust the vehicle speed.
Driving on downslopes
On long or steep downslopes, increase
the amount deceleration using the
regenerative braking in regenerative
braking level change mode.
CAUTION
 On long downslopes, operate the
regenerative braking and the foot
brake together. Frequent
deceleration by depressing the brake
pedal could cause the disc brakes to
overheat and become ine ffective.
 If only strong regenerative braking is
used continuously, it could stop
working temporarily.
Regeneration braking is less e ffective
the closer the high voltage battery is
to a full charge, and regeneration
braking will not work when the high
voltage battery is fully charged.
Stopping the vehicles
1. After completely stopping the vehicle, continue to depress the
brake pedal firmly.
2. If necessary, apply the parking brake with the brake pedal
depressed.
3. If the vehicle is going to be parked for a long time, shift the selector
lever to the P position with the
brake pedal depressed.
WARNING
Do not depress the accelerator pedal
unnecessarily while the vehicle is
stopped:
If the accelerator pedal is mistakenly
depressed when the selector lever is in
a position other than the P or N
position, the vehicle could suddenly
accelerate resulting in an accident.
After stopping the vehicle, check the
shift position indication in the
instrument cluster before
re-accelerating:
If the vehicle were to move in the
unintended direction, it could lead to
an accident.
CAUTION
Do not depress the accelerator pedal
and the brake pedal at the same time,
or rev the motor with the selector lever
in the forward drive position while the
vehicle is stopped on an upslope. The
motor could overheat and lead to
damage.
When Driving
Selector Lever Position Functions
4-33
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Pa r k i n g t h e v e h i c l e
1. After completely stopping thevehicle, continue to depress the
brake pedal firmly.
2. Shift the selector lever to the P
position with the brake pedal
depressed.
3. Make sure that the shift position is in the P position using the shift
position indication in the
instrument cluster.
4. Apply the parking brake with the
brake pedal depressed.
5. Press the power switch to stop the
EV system.
CAUTION
Completely stop the vehicle before
shifting the selector lever to the P
position. If the selector lever is shifted
to the P position before the vehicle is
completely stopped, unnecessary force
will be applied to the EV transaxle
which could cause damage.
Other precautions
WARNING
Do not allow the vehicle to move in
reverse on an upslope while the
selector lever is in forward drive, or
move forward on an downslope while
the selector lever is in reverse drive:
Otherwise, the EV system could stop,
making the steering wheel difficult to
control, which could result in an
accident.
When Driving
Selector Lever Position Functions
4-34
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Lighting Control
▼Headlights
Turn the headlight switch to turn the head
lights and other exterior lights on or off.
When the taillights, parking lights, and th e license plate lights are turned on, the
lights-on indicator light in th e instrument cluster turns on.

NOTE
Do not leave the headlights and exterior lights on while the EV system is turned
o ff. Otherwise, the battery power could be depleted.
Headlights do not blind drivers approaching in the opposite direction no matter
what side of the road you must drive yo ur vehicle (left-hand or right-hand traffic).
Therefore, it is not necessary to adjust the optical axis of the headlights when
switching temporarily to driving on the opposite side of the road (left-hand or
right-hand tra ffic).
Power switch posi-
tion ACC or OFF ON
Switch Position OFF
*1AUTOOFF*1AUTO
Headlights Off Off OffOff
Auto
*2*4Auto*3*4
On
Daytime running
lights Off
Off OffOff Off
Taillights
Parking lights
License plate lights Off
Off On
Off On
*1 The light switch returns to the AUTO position automatically.
When Driving
Switches and Controls
4-35
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Refer to the Settings section in the Mazda Connect Owner's Manual.
▼Headlight High-Low Beam
The headlights switch between high
and low beams by moving the lever
forward or backward.

1. High beam
2. Low beam

When the headlight high-beams are
on, the headlight high-beam indicator
light is turned on.

▼Flashing the Headlights
When the power switch is switched
ON, and regardless of the headlight
position, the headlights switch to high
beams while the lever is being pulled.

1. OFF
2. Headlight
flashing

The headlight high-beam indicator
light in the instrument cluster
illuminates simultaneously. The lever
will return to the normal position when
released.

▼ Coming Home Light
The coming home light turns on the
headlights (low beams) when the lever
is operated.
To turn on the lights
When the lever is pulled with the
power switch switched to ACC or OFF,
the low beam headlights turn on.
The headlights turn o
ff after a certain
period of time has elapsed after all of
the doors are closed.
NOTE
The time until the headlights turn off
after all of the doors are closed can
be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
If no operations are done for 3
minutes after the lever is pulled, the
headlights turn off.
The headlights turn o ff if the lever is
pulled again while the headlights are
illuminated.
▼ Leaving Home Light
The leaving home light turns on the
lights when the transmitter unlock
When Driving
Switches and Controls
4-37
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Daytime Running Lights
Some countries require moving
vehicles to have their lights on
(daytime running lights) during the
daytime.

The daytime running lights turn on
automatically.
NOTE
(Except Canada)
The daytime running lights can be
deactivated.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Turn and Lane-Change
Signals
▼Turn and Lane-Change Signals
The turn and lane-change signals can
be used when the power switch is
switched ON.
▼Tu r n S i g n a l s
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel
after the turn is completed.

If the indicator light continues to
flash
after a turn, manually return the lever
to its original position.
1. Right turn
2. Right lane change
3. OFF
4. Left lane change
5. Left turn

The turn signal indicators in the
instrument cluster flash according to
the operation of the turn signal lever to
show which signal is working.

When Driving
Switches and Controls
4-39
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Rear Window Defogger
▼Rear Window Defogger
The rear window defogger clears fog
from the rear window.

The rear window defogger can be used
when the power switch is switched
ON.

Press the switch to turn on the rear
window defogger. The rear window
defogger operates for about 15
minutes and then turns o
ff
automatically.
The indicator light illuminates when
the defogger is operating.

To t u r n o ff the rear window defogger
before the 15 minutes has elapsed,
press the switch again.
1. Indicator light
CAUTION
 Do not use sharp instruments or
window cleaners with abrasives to
clean the inside of the rear window
surface. They may damage the
defogger grid inside the window.
NOTE
This defogger is not designed for
melting snow. If there is an
accumulation of snow on the rear
window, remove it before using the
defogger.
The rear window defogger operation
time can be changed from 15
minutes to continuous operation.
When the operation time has been
switched to continuous operation,
by pressing the switch, the rear
window defogger will continue to
operate until the power switch is
switched OFF.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼ Windshield Wiper De-icer*
The thermal
filaments at the following
positions heat up and facilitate the
removal of snow accumulated on the
windshield.
The windshield wiper de-icer operates
in conjunction with the rear window
defogger.
Press the rear window defogger switch
when the power switch is switched ON
When Driving
Switches and Controls
*Some models.4-45
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07