lights MAZDA MODEL MX-30 EV 2022 Workshop Manual

Fuses
▼Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate
circuit protector. If a fuse has blown,
the inside element will be melted.

If the same fuse blows again, avoid
using that system and consult an
Authorized Mazda Dealer as soon as
possible.
▼Fuse Replacement
Replacing the fuses on the vehicle's
left side
If the electrical system does not work,
fi
rst inspect the fuses on the vehicle's
left side.

1. Make sure the power switch is
switched o ff, and other switches
are off.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the
fuse puller provided on the fuse
block located in the motor
compartment.
4. Inspect the fuse and replace it if it is
blown.
1. Normal
2. Blown

5. Insert a new fuse of the same amperage rat ing , and make sure it
fits tightly. If it does not
fit tightly,
have an expert install it. Consult an
Authorized Mazda Dealer.
If you have no spare fuses, borrow
one of the same rating from a
circuit not essential to vehicle
operation, such as the audio or
accessory socket circuit.
6. Reinstall the cover and make sure that it is securely installed.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the
fuse block under the hood.
Maintenance and Care
Owner Maintenance
6-27
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

No.FUSE RAT
-
ING PROTECTED COMPONENT
F16 15 A Illumination
F17 10 A Brake lights
F18 10 A Reverse lights
F19 10 A Rear turn signal lights
F20 10 A Taillights
F21 10 A Taillights
F22 7.5 A Air Bag
F23 ――
Maintenance and Care
Owner Maintenance
6-33
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Do not rub the camera cover or lens
forcefully, or clean them with an
abrasive or hard brush.
NOTE
If there are water droplets, snow, or
mud on the camera lens, wipe it o ff
using a soft cloth. If the camera lens is
especially dirty, wash it o ff with mild
detergent.
▼ Aluminum Wheel Maintenance
A protective coating is provided over
the aluminum wheels. Special care is
needed to protect this coating.
CAUTION
Do not use any detergent other than
mild detergent. Before using any
detergent, verify the ingredients.
Otherwise, the product could discolor
or stain the aluminum wheels.
NOTE
Do not use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
Avoid washing your vehicle in an
automatic car wash that uses
high-speed or hard brushes.
▼Plastic Part Maintenance
When cleaning the plastic lenses of
the lights, do not use gasoline,
kerosene,
rectified spirit, paint,
thinner, highly acidic detergents, or
strongly alkaline detergents.
Otherwise, these chemical agents
can discolor or damage the surfaces
resulting in a signi ficant loss in
functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
coolant, or lead-acid battery fluid, it
could cause discoloration, staining ,
or paint peeling. Wipe o ff any such
chemical agents or fluids using a soft
cloth immediately.
High water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
Do not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
In addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Maintenance and Care
Appearance Care
6-39
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

7If Trouble Arises
Helpful information on what to do if a problem arises with the
vehicle.
Parking in an Emergency............ 7-2 Parking in an Emergency......... 7-2
Flat Tire................................... 7-3 Tool Storage.......................... 7-3
Emergency Flat Tire Repair
Kit........................................ 7-4
Changing a Flat Tire..............7-10
Troubleshooting for Charging ..........
............................................ 7-11 What to do when charging is not
possible.............................. 7-11
Depleted Lead-acid Battery...... 7-12 Jump-Starting...................... 7-12
Fully Discharged High Voltage
Battery...................................7-16 Fully Discharged High Voltage
Battery................................ 7-16
Emergency Starting................. 7-17 Push-Starting....................... 7-17
Emergency Towing.................. 7-18 Towing Description.............. 7-18
Tiedown Hooks*.................. 7-19
Warning/Indicator Lights and
Warning Sounds..................... 7-21 If a Warning Light Turns On or
Flashes................................ 7-21
Message Indicated on Multi-
information Display............. 7-33
Warning Sound is
Activated.............................7-37
When Liftgate Cannot be
Opened................................. 7-42 When Liftgate Cannot be
Opened.............................. 7-42
Active Driving Display Does Not
Operate................................. 7-43 If the Active Driving Display Does
Not Operate........................ 7-43
Windshield Wipers Operate at High
Speed.................................... 7-44 Windshield Wipers Operate at
High Speed......................... 7-44
*Some models.7-1
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Parking in an Emergency
▼Parking in an Emergency
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a
traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the turn signals will flash. The
hazard warning indicator lights in the
instrument cluster flash simultaneously.
NOTE
The turn signals do not work when
the hazard warning lights are on.
Check local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
If Trouble Arises
Parking in an Emergency
7-2
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

12.Adhere the speed restriction stickerto an area where it can be viewed
easily by the driver.

13.Adhere the repaired tire sticker tothe wheel of the flat tire.

WARNING
Do not adhere the speed
restriction sticker to the padded
area on the steering wheel:
Adhering the speed restriction
sticker to the padded area on the
steering wheel is dangerous
because the air bag may not
operate (deploy) normally resulting
in serious injury. In addition, do not
adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
14.When the tire in flates to the
specified tire in flation pressure, turn
the air compressor switch o ff, turn
the sleeve of the injection hose to
the left, and pull it out of the tire
valve.
15.Remove the air compressor hose from the injection valve of the
bottle. After that, install the
injection hose to the injection valve
of the bottle to prevent leakage of
any remaining sealant.

CAUTION
The remaining sealant in the hose
may spray out when the hose is
removed. Remove the hose
carefully because you may not be
able to remove the sealant
contacting clothing or other
objects.
16.Install the tire valve cap.
17.Put the emergency flat tire repair kit
into the trunk.
18.Start driving immediately to spread the sealant in the tire.
CAUTION
Carefully drive the vehicle at a
speed of 80 km/h (50 mph) or less.
If the vehicle is driven at a speed of
80 km/h (50 mph) or more, the
vehicle may vibrate.
If Trouble Arises
Flat Tire
7-8
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Jump-Starting
▼Jump-Starting
The lead-acid battery might be depleted
if the following conditions occur.
The EV system does not start.The selector lever cannot be shifted to a position other than P.The horn sound is weak or it does not sound.The brightness of the lights is extremely low.
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If
you feel unsure about jump-starting, we strongly recommend that you have a
competent service technician do the work.
Using commercially available booster cables, connect the lead-acid battery of the
booster vehicle’s battery to the lead-acid battery of your vehicle and start the EV
system.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the lead-acid battery, read the following
precautions carefully before using the lead-acid battery or inspecting it.
Keep flames and sparks away from open lead-acid battery cells and do not
allow metal tools to contact the positive (+) or negative (–) terminal of the
lead-acid battery when working near a lead-acid battery. Do not allow the
positive (+) terminal to contact the vehicle body:
Flames and sparks near open lead-acid battery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An exploding lead-acid battery can cause serious burns
and injuries. Keep all flames including cigarettes and sparks away from open
lead-acid battery cells.
If Trouble Arises
Depleted Lead-acid Battery
7-12
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

If a Warning Light TurnsOn or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/
flashes,
take appropriate action for each light.
There is no problem if the light turns
o ff, however if the light does not turn
o ff or turns
on/flashes again, consult
an Authorized Mazda Dealer.
WARNING
If the warning light/indicator light
turns on or flashes, park the vehicle in
a safe place immediately and take
appropriate measures.
Continuing to drive the vehicle while
ignoring the illumination/ flashing of
the warning light/indicator light is
dangerous because a problem may
occur to a vehicle system, or it could
lead to an accident.
The details for some warnings can be
viewed on the center display or
multi-information display in the
instrument cluster.
Center display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to view the warning details.
Multi-information display
1. Press the INFO switch on the steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-11.
▼Brake System Warning Indication/
Warning Light
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the power
switch is switched on and turns o
ff a
few seconds later, or when the EV
system is started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an Authorized Mazda
Dealer.
Refer to Inspecting Brake Fluid Level on
page 6-12.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-21
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

CAUTION
In addition, the
eff ectiveness of the
braking may diminish so you may
need to depress the brake pedal
more strongly than normal to stop
the vehicle.
 When starting the EV system, the
brake system warning light may turn
on and the warning indication may
be displayed. In this case, park the
vehicle in a safe location and release
the brake pedal.
If the brake system warning light/
warning indication does not turn o ff
even after parking the vehicle, have
the vehicle inspected by an
Authorized Mazda Dealer.

▼ Electronic Brake Force Distribution
System Warning
If the electronic brake force
distribution control unit determines
that some components are operating
incorrectly, the control unit may
illuminate the brake system warning
light and the ABS warning light
simultaneously. The problem is likely to
be the electronic brake force
distribution system.
WARNING
Do not drive with both the brake
system warning light and ABS warning
light illuminated. Have the vehicle
towed to an Authorized Mazda
Dealer to have the brakes inspected as
soon as possible:
Driving when the brake system warning
light and ABS warning light are
illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly in
an emergency stop than under normal
circumstances.
▼ Lead-acid Battery Charging System
Warning Indication/Warning Light
The lead-acid battery charging system
warning indication/warning light
displays/turns on if the charging
system has a malfunction while the EV
system is operating.
Drive to the side of the road and park
o
ff the right-of-way. Consult an
Authorized Mazda Dealer.
WARNING
Do not drive the vehicle with the
lead-acid battery charging system
warning indication/warning light
displayed/turned on:
Otherwise, the EV system could stop
unexpectedly and the parking lock may
not operate which could result in an
accident.
▼ EV System Problem Warning
Indication/Warning Light
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-22
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

“EV System Malfunction. Have the
Vehicle Inspected” is displayed
The indication/light displays/turns on
if the system has a problem.
Have your vehicle inspected by an
Authorized Mazda Dealer.
“EV System Malfunction. Stop the
Vehicle in a Safe Location” is
displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
“Electrical Leakage in EV System
Detected Stop the Vehicle in a Safe
Location” is displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
WARNING
Do not open the hood:
If you touch something in the motor
compartment, it could lead to an
electrical shock resulting in an
accident.
CAUTION
If the light turns on while driving, the
EV system cannot be started when the
power switch is switched OFF once.
▼ High Voltage Battery Temperature
War n in g I nd ic at ion
“Excessive High Voltage Battery
Temperature. Drive Slowly” is
displayed
The indication displays if the high
voltage battery temperature is
excessively high.
Drive slowly to reduce load on the high
voltage battery.
Stop the vehicle in a safe place if
necessary. If the indication remains
displayed, the system may have a
problem. Have the vehicle inspected
by an Authorized Mazda Dealer.
“High Voltage Battery Temperature Is
Low Acceleration Is Limited” is
displayed
The indication displays if the high
voltage battery temperature is
excessively low.
The vehicle speed may not increase
even if the accelerator pedal is
depressed because the motor output is
restricted.
If the indication remains displayed, the
system may have a problem. Have the
vehicle inspected by an Authorized
Mazda Dealer.
▼Remaining High Voltage Battery
Power Warning Indication/
Warning Light
“High Voltage Battery Is Low. Charge
Battery Soon” displays/turns on
The indication displays when the
remaining high voltage battery power
is low.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-23
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07