warning light MAZDA MODEL MX-5 MIATA 2002 Owner's Guide

5-22
Driving Your Mazda
Form No. 8Q42-EA-01F
Warning/Indicator Lights and Beeps
Warning/Indicator Lights
SignalWarning/Indicator Lights Page
Brake System Warning Light 5-24
Seat Belt Warning Light 5-25
Charging System Warning Light 5-25
Check Engine Light 5-26
ABS Warning Light 5-26
Air Bag/Seat Belt Pretensioner System Warning Light 5-27
Immobilizer System Warning Light 5-27
Warning/Indicator lights will appear in any of the highlighted areas
J07L(02MY).book Page 22 Monday, June 11, 2001 4:52 PM

5-23
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F
Headlight High-Beam Indicator Light5-27
O/D OFF Indicator Light 5-28
Cruise Set Indicator Light 5-28
Signal
Warning/Indicator Lights Page
J07L(02MY).book Page 23 Monday, June 11, 2001 4:52 PM

5-24
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F

Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution
system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-17).
2. After adding fluid, check the light again. If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
Even if the light goes off, have your brake
system inspected as soon as possible.
Electronic brake force distribution
system warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may turn the brake system
warning light on.
In this case, the ABS warning light comes
on at the same time (page 5-26).
J07L(02MY).book Page 24 Monday, June 11, 2001 4:52 PM

5-25
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F

Seat Belt Warning Light/Beep
If the driver’
s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds and the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.

Charging System Warning Light
This warning light indicates a malfunction
of the alternator or of the charging system.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
2. Turn off the engine. Inspect the alternator drive belt for looseness and
breakage.
3. If it ’s OK, the charging system has a
problem. Consult an Authorized
Mazda Dealer as soon as possible.
Brake Warning Light:
Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, have the brakes
inspected immediately. Don ’t drive
with this light on, and contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don ’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J07L(02MY).book Page 25 Monday, June 11, 2001 4:52 PM

5-26
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F

Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
• The fuel tank level being very low or
approaching empty.
• The engine
’s electrical system has a
problem.
• The emission control system has a
problem.
• The fuel-filler cap is missing or not
tightened securely.
If the check engine light flashes
continuously, decrease your speed and
consult an Authorized Mazda Dealer as
soon as possible.

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you
’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
Don
’t drive with a loose or broken
alternator belt. The engine could
overheat because this belt also drives
the water pump.
CAUTION
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don ’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J07L(02MY).book Page 26 Monday, June 11, 2001 4:52 PM

5-27
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F

Air Bag/Seat Belt Pretensioner
System Warning Light
If the air bag/seat belt pretensioner system
is OK, the warning light comes on when
the ignition switch is turned to the ON
position or after the engine is cranked.
After about 6 seconds it goes out.
A system malfunction is indicated when
the warning light constantly flashes, stays
on or doesn
’t come on at all. If any of
these occur, consult an Authorized Mazda
Dealer as soon as possible. The system
may not work in an accident.

Immobilizer System Warning
Light
If the immobilizer system is working
properly, the light will come on when the
ignition switch is turned to the ON or
START position. The light will go out
when confirmation by the immobilizer
system is completed.
If the light flashes rapidly, fails to come
on, or comes on and stays on, it indicates
a system malfunction. If any of these
occur, contact an Authorized Mazda
Dealer as soon as possible.

Headlight High-Beam Indicator
Light
This light indicates one of two things:
• The high-beam headlights are on.
• The turn signal lever is in the flash-to-
pass position.
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
Self-Servicing the Air Bag/
Pretensioner Systems:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled. This
could cause serious injuries. Never
tamper with the systems and always
have an Authorized Mazda Dealer
perform all servicing and repairs.
WARNING
J07L(02MY).book Page 27 Monday, June 11, 2001 4:52 PM

5-28
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q42-EA-01F

O/D OFF Indicator Light
This light comes on when the overdrive
has been turned off.

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.
If the overdrive-off indicator light
flashes, the transaxle has an electrical
problem. Continuing to drive your
Mazda in this condition could cause
damage to your transaxle. Consult an
Authorized Mazda Dealer as soon as
possible.
CAUTION
Beeps
J07L(02MY).book Page 28 Monday, June 11, 2001 4:52 PM

5-31
Driving Your Mazda
Switches and Controls
Form No. 8Q42-EA-01F
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.The ignition switch must be in the ON
position.
Daytime Running Lights
NOTE
The running lights go off when the
parking brake is applied.
Windshield Wipers and
Washer
Frozen Washer Fluid:
Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don
’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected by a circuit breaker. This
mechanism will automatically stop
operation of the blades, but only for
about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don ’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
J07L(02MY).book Page 31 Monday, June 11, 2001 4:52 PM

5-34
Driving Your Mazda
Switches and Controls
Form No. 8Q42-EA-01F
The hazard warning lights should always
be used when you stop on or near a
roadway.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning switch and all
four turn signals will flash at once.
Hazard Warning Flasher
NOTE
•The turn signals don
’t work when
the hazard warning lights are on.
• Check local regulations about the
use of hazard warning lights while
the vehicle is being towed. They
may forbid it.
Hazard warning flasher switch
J07L(02MY).book Page 34 Monday, June 11, 2001 4:52 PM

6-6
Interior Comfort
Climate Control System
Form No. 8Q42-EA-01F
Mode selector dial
Turn the mode selector dial to select
airflow mode (page 6-4).
A/C switch
Push the switch to turn the air conditioner
on. An indicator light on the switch will
illuminate when the fan control dial is on.
Push the switch once again to turn the air
conditioner off.Air intake selector
This lever controls the source of air
entering the vehicle.
It is recommended that under normal
conditions the lever be kept in the outside
air position.
Outside air position ( )
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
Recirculated air position ( )
Outside air is shut off. Air within the
vehicle is recirculated.
This position can be used when driving on
a dusty road or in similar conditions. It
also helps to provide quicker cooling of
the interior.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0
°C ( (32 ° F).
The Recirculated Air Position:
Using the position in cold
weather will cause the glass to fog up.
Your vision will be hampered, which
could lead to a serious accident. Do
not use the position in cold
weather.
WARNING
J07L(02MY).book Page 6 Monday, June 11, 2001 4:52 PM