light MAZDA MODEL MX-5 MIATA 2003 Owner's Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2003, Model line: MODEL MX-5 MIATA, Model: MAZDA MODEL MX-5 MIATA 2003Pages: 256, PDF Size: 5.3 MB
Page 85 of 256
5-3
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes) should be inspected
before the engine is started (page 5-22).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-22).
Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened. 1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. (Manual transmission)
Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
(Automatic transmission)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the
clutch pedal is not
pushed down all the
way.
NOTE
The starter will not operate if the shift
lever is not
in P or N.
J07R_8R09_EA_02G_Edition4.book Page 3 Monday, February 3, 2003 1:16 PM
Page 87 of 256
5-5
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
Parking Brake
Setting the parking brake
Depress the brake pedal, then pull the
brake handle fully upward.
Releasing the parking brake
Depress the brake pedal, then pull the
handle up and press the button. Lower the
handle to the release position while
holding in the button.
Driving with the Engine Off:
Continuing to drive when the engine
is stalled or turned off is dangerous.
Braking will require more effort, and
the brake
’s power-assist could be
depleted if you pump the brake. This
will cause longer stopping distances
or even an accident. Don ’t continue
driving when the engine is stalled or
turned off, find a safe place to stop.
Riding the Brakes:
Driving with your foot continuously
on the brake pedal or steadily
applying the brakes for long distances
is dangerous. This causes overheated
brakes, resulting in longer stopping
distances or even total brake failure.
This could cause loss of vehicle
control and a serious accident. Avoid
continuous application of the brakes.
Shift to a lower gear when going
down steep hills.
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
Driving with the parking brake on will
cause excessive wear of the brake
linings or pads.
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 5 Monday, February 3, 2003 1:16 PM
Page 88 of 256
5-6
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution
system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-17).
2. After adding fluid, check the light again.
If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer. Even if the light goes off, have your brake
system inspected as soon as possible.
Electronic brake force distribution
system warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may turn the brake system
warning light on.
In this case, the ABS warning light comes
on at the same time (page 5-26).
Brake Warning Light:
Driving with the brake system warning
light on is dangerous. It indicates that
your brakes may not work at all or that
they could completely fail at any time.
If this light remains on, after checking
that the parking brake is released, have
the brakes inspected immediately.
Don
’t drive with this light on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon as
possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don ’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J07R_8R09_EA_02G_Edition4.book Page 6 Monday, February 3, 2003 1:16 PM
Page 89 of 256
5-7
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
Anti-Lock Brake System (ABS)
The ABS control unit continuously
monitors the speed of each wheel. If one
is about to lock up, the ABS responds by
automatically releasing and reapplying
that wheel
’s brake.
The driver will feel a slight vibration in
the brake pedal and may hear a chattering
noise from the brake system. This is
normal when the ABS operates. Don ’t
pump the brakes, continue to press down
on the brake pedal.
ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’
re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
ABS:
The ABS cannot compensate for
unsafe and reckless driving, excessive
speed, tailgating (following another
vehicle too closely), and hydroplaning
(reduced tire friction and road
contact because of water on the road
surface). You can still have an
accident. So don ’t rely on ABS as a
substitute for safe driving.
NOTE
Braking distances may be longer on
loose surfaces (snow or gravel, for
example) which usually have a hard
foundation. A vehicle with a normal
braking system may require less
distance to stop under these conditions
because the tires will build up a wedge
of surface layer when the wheels skid.
WARNING
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don ’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J07R_8R09_EA_02G_Edition4.book Page 7 Monday, February 3, 2003 1:16 PM
Page 90 of 256
5-8
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
Brake Pad Wear Indicator
When the disc brake pads become worn,
the built-in wear indicators contact the
disc plates. This causes a screeching noise
to warn that the pads should be replaced.
When you hear this noise, consult an
Authorized Mazda Dealer as soon as
possible.
Manual Transmission Shift
Pattern
The shift pattern of the transmission is
conventional, as shown.
Press the clutch pedal all the way down
while shifting; then release it slowly.
(5-speed transmission)
A safety feature prevents accidental
shifting from 5 to reverse. The shift lever
must be put in neutral before being shifted
to reverse.
(6-speed transmission)
Vehicles with 6-speed transmission are
equipped with a device to prevent shifting
to reverse by mistake. Apply greater than
normal force when shifting to reverse.
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
Driving with Worn Disc Pads:
Driving with worn disc pads is
dangerous. The brakes could fail and
cause a serious accident. As soon as
you hear a screeching noise consult
an Authorized Mazda Dealer.
WARNING
Manual Transmission
Operation
5-speed transmission
6-speed transmission Neutral position
Neutral position
J07R_8R09_EA_02G_Edition4.book Page 8 Monday, February 3, 2003 1:16 PM
Page 92 of 256
5-10
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
Various Lockouts:
Transmission Ranges
The shift lever must be in P or N to
operate the starter.
P (Park)
P locks the transmission and prevents the
rear wheels from rotating.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete stop
before shifting to or from R, except as
explained under Rocking the Vehicle
(page 4-7).
N (Neutral)
In N, the wheels and transmission are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
Automatic Transmission
Controls
Indicates that you must depress the
brake pedal and hold in the lock-
release button to shift (The ignition
switch must be in the ON position).
Indicates the shift lever can be
shifted freely into any position.
Indicates that you must hold in the
lock-release button to shift.
Lock-release button
To prevent unsafe
shifting
Shift pattern
indicator
Shows shift lever
position
Overdrive button
For turning the
overdrive off or on
Holding the Vehicle with P:
Setting the shift lever to the P position
without using the parking brake to
hold the vehicle is dangerous. If P
fails to hold, the vehicle could move
and cause an accident. To hold the
vehicle, set the shift lever to P AND
set the parking brake.
•
Shifting into P, N or R while the
vehicle is moving can damage your
transmission.
• Shifting into a driving gear or
reverse when the engine is running
faster than idle can damage the
transmission.
WARNING
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 10 Monday, February 3, 2003 1:16 PM
Page 95 of 256
5-13
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
O/D OFF indicator light
This light comes on when the overdrive
has been turned off.
Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress the
accelerator fully. The transmission will shift
to a lower gear, depending on vehicle speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or 1, depending on the load
weight and grade steepness.
3. Release all brakes while gradually accelerating.
Descending steep grades
When descending a steep grade, shift to 2 or 1,
depending on load weight and grade steepness.
Descend slowly, using the brakes only
occasionally to prevent them from overheating.
Power steering is only operable when the
engine is running. If the engine is off or if
the power steering system is inoperable,
you can still steer, but it requires more
physical effort.
If the steering feels rigid during normal
driving, consult an Authorized Mazda
Dealer.
If the overdrive-off indicator light
flashes, the transmission has an
electrical problem. Continuing to drive
your Mazda in this condition could
cause damage to your transmission.
Consult an Authorized Mazda Dealer
as soon as possible.
CAUTION
Power Steering
Never hold the steering wheel to the
extreme left or right for more than 5
seconds with the engine running.
This could damage the power steering
system.
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 13 Monday, February 3, 2003 1:16 PM
Page 96 of 256
5-14
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
With cruise control, you can set and
automatically maintain any speed of more
than about 40 km/h (25 mph).
Cruise Set Indicator Light
This light comes on when a cruising speed
is set.
Activation/Deactivation
To activate the system, press the CRUISE
MAIN switch.
To deactivate the system, push the switch
again.
Cruise Control
Cruise Control Use:
Using cruise control in the following
conditions could cause you to lose
control of the vehicle:
•
Heavy or unsteady traffic
• Slippery or winding roads
• Similar restrictions that require
inconsistent speed
Don ’t use cruise control in these
situations.
WARNING
Cruise Main Switch:
Leaving the CRUISE MAIN switch
on when not using the cruise control
is dangerous as it may be switched on
accidentally. This could result in loss
of vehicle control. Keep the CRUISE
MAIN switch off when cruise control
is not in use.
Indicator light
WARNING
J07R_8R09_EA_02G_Edition4.book Page 14 Monday, February 3, 2003 1:16 PM
Page 98 of 256
5-16
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G
To Decrease Cruising Speed
Turn the control knob to SET/COAST and
hold it. The vehicle will gradually slow.
Release the knob at the speed you want.
To Resume Cruising Speed at
More Than 40 km/h (25 mph)
If some other method besides the CRUISE
MAIN switch was used to cancel cruising
speed and the system is still activated, the
most recent set speed will automatically
resume when the control knob is turned to
RESUME/ACCEL.
If vehicle speed is below 40 km/h (25
mph), increase the vehicle speed up to 40
km/h (25 mph) and turn the control knob
to RESUME/ACCEL.
To C a n c e l
To turn off the system, use one
of these
methods:
• Press the CRUISE MAIN switch.
• Slightly depress the brake pedal.
• (Manual transmission)
Depress the clutch pedal.
The system is off when the ignition is off.
Control knob
Control knob
NOTE
Cruise control will cancel at about 15
km/h (9 mph) below the preset speed
or below 40 km/h (25 mph).
J07R_8R09_EA_02G_Edition4.book Page 16 Monday, February 3, 2003 1:16 PM
Page 102 of 256
5-20
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8R09-EA-02G
Fuel Gauge
The fuel gauge shows approximately how
much fuel is in the tank. We recommend
keeping the tank over 1/4 full. When the
low fuel warning light illuminates or
when the needle is near E, refuel as soon
as possible.
Engine Oil Pressure Gauge
Engine oil pressure is normal when the
engine oil pressure gauge needle points
halfway between L and H with the engine
running.
If the needle on the gauge doesn
’t move
after starting the engine, follow steps 1
through 3. If the engine oil pressure gauge moves to
L (low) while you are driving, drive to the
side of the road and park off the right-of-
way. Set the parking brake. Then follow
steps 1 through 3.
1. Turn off the engine and inspect the
engine oil level (page 8-13). If it ’s low,
add oil.
2. Start the engine.
3. If the needle still doesn ’t move, have
your vehicle checked at an Authorized
Mazda Dealer.
Don ’t run the engine if the oil pressure
is low. It could result in extensive
engine damage.
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 20 Monday, February 3, 2003 1:16 PM