buttons MAZDA MODEL MX-5 MIATA 2003 Owners Manual

3-19
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
5. Push the unlock buttons and fully release the top latches.
6. Lift up on the front section of the top to release it from the windshield header. 7. Fold back the front and carefully lower
it to the storage area, then put the
latches in the locked position.

Covering the Convertible Top
1. Cover the convertible top with the top
covering, stored in the trunk.
2. Feed the straps on the bottom of the covering through the lower links and
snap them into position.
3. Secure the top covering with the straps.
4. Affix the top covering fasteners.
Unlock button Top latch
Windshield header
Top covering
Link Strap
J07R_8R09_EA_02G_Edition4.book Page 19 Monday, February 3, 2003 1:16 PM

3-20
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
5. Insert the top covering’s rear edge into
the groove in the body molding.

Raising the Convertible Top
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Undo the fasteners and straps. 5. Remove the top covering and store it
properly in the trunk.
6. Unlock the top latches and open them fully.
7. Hold the top lift handle and pull the top up and forward until it ’s against the
windshield header.
8. After securely hooking the top latches onto the windshield header, push each
latch up with the palm of your hand
until the lock buttons click and the
latches are locked.
Never drive with the top partially
folded or uncovered. Otherwise the top
and/or the top covering could be
damaged.
Top covering
Body
Molding
CAUTION
Sunvisor Sunvisor
Windshield header
J07R_8R09_EA_02G_Edition4.book Page 20 Monday, February 3, 2003 1:16 PM

3-23
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
•Before removing or installing the
hardtop, stop in a safe place off the
right-of-way and park on a level
surface.
• When removing the hardtop, make sure
objects inside the vehicle aren
’t blown
away by the wind.
• Secure all loose objects inside before
driving with the hardtop removed.
• Don
’t drive through an automatic car
wash; it may damage the hardtop.
• Don
’t remove or install the hardtop
when the wind is strong; the wind
could damage the hardtop.
• When removing the hardtop, make sure
the operation is performed by 2
persons.
• Before removing the hardtop, lower the
antenna.
• Removing the hardtop while it
’s wet
can cause water to drip into the
passenger compartment.

Removing the Detachable
Hardtop
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Push the unlock buttons and fully release the top latches.Fa s t e n i n g M e c h a n i s m s :
It is dangerous to place your hands or
fingers near the fastening
mechanisms. Your hands or fingers
could be caught and injured by the
mechanism. Always keep your hands
and fingers away from the fastening
mechanisms when moving the top.
WARNING
Sunvisor Sunvisor
Unlock button
Top latch
J07R_8R09_EA_02G_Edition4.book Page 23 Monday, February 3, 2003 1:16 PM

3-24
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
5. Push the unlock buttons and fully release the side latches.
6. Disconnect the rear window defroster coupler. 7. Slide the hardtop rearward while
pressing down on the rear deck latches
to unlock the latches.
8. Lift the hardtop straight off the body to prevent damage to the rear deck latches
and studs.
Unlock button
Side latch
Rear window defroster coupler
Wi nd shiel d ’s Edges:
Not being careful of the windshield ’s
edges when getting into or out of the
vehicle is dangerous. The
windshield ’s edges could scratch and
cause injuries.
Be careful of the windshield ’s edges
when getting into or out of the
vehicle.
Rear deck latch
Hardtop
Rear deck stud
WARNING
J07R_8R09_EA_02G_Edition4.book Page 24 Monday, February 3, 2003 1:16 PM

3-26
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
5. Align the rear deck latches with the rear deck studs and set the hardtop
squarely onto the body.
6. Slide the hardtop forward while pressing down on the rear deck latches
to lock the latches, and then verify that
they are secure by attempting to lift the
rear of the hardtop. 7. Push each top latch up with the palm of
your hand until the lock buttons click
and the latches are locked.
Rear deck stud
Hardtop
Rear deck latch
Rear deck latch
Rear deck latch
• Be careful not to strike the body
with any of the protruding hardtop
latches.
• The rear defogger grid and the
defogger cord could be damaged
when removing or installing the top.
Make sure the rear defogger grid
isn
’t folded and the defogger cord
isn ’t caught between the vehicle ’s
body and the top.
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 26 Monday, February 3, 2003 1:16 PM

3-27
Knowing Your Mazda
Doors and Locks
Form No. 8R09-EA-02G
8. Push each side latch down with the palm of your hand until the lock
buttons click and the latches are
locked.
9. Reconnect the rear window defroster coupler.

Detachable Hardtop Appearance
Care
Refer to detachable hardtop maintenance
(page 8-47) for information on detachable
hardtop appearance care.
After installation, verify that all latches
are secure. Operating the vehicle with
unlocked latches may cause hardtop
damage or loss.
Side latch
CAUTION
Rear window defroster coupler
NOTE
If the top rattles even when all latches
are secure, contact your Authorized
Mazda Dealer for inspection.
J07R_8R09_EA_02G_Edition4.book Page 27 Monday, February 3, 2003 1:16 PM

6-24
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G

Operating the Radio
Radio ON
Press a band selector button ( or
) to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning knob will
change the frequency higher or lower.
Band selector buttons Display
Channel preset buttons Scan button
Auto memory
button
Manual tunin
g knob
Seek tuning
button
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J07R_8R09_EA_02G_Edition4.book Page 24 Monday, February 3, 2003 1:16 PM

6-32
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G

Operating the In-Dash CD Changer
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "In" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 5 seconds
after the beep is heard.
3. When "In" is displayed, insert the CD.
Display CD slot
Disc-in indicator
CD ejectbutton
CD play button
Random button
Repeat button
Disc up button Scan
button
Fast-forward
button
Reverse button
Track up
button
Track down
button
Disc down
button
Load button
Power/Volume knob
Channel preset buttons
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume knob and the load
button ( ) for about 2 seconds will
turn this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
J07R_8R09_EA_02G_Edition4.book Page 32 Monday, February 3, 2003 1:16 PM