MAZDA MODEL MX-5 MIATA POWER RETRACTABLE HARDTOP 2008 Owners Manual

Black plate (321,1)
(Halogen bulb)
NOTE
Replacing low-beam halogen bulbs is difficult
therefore contacting an Authorized Mazda
Dealer is recommended.
1. If you are changing the right headlightbulb, start the engine, turn the steering
wheel all the way to the left, and turn
off the engine. If you are changing the
left headlight bulb, turn the steering
wheel to the right.
2. Turn the screws counterclockwise and remove them.
3. Turn the center section of the plasticretainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Disconnect the electrical connector from the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.
7. Swing the retaining spring out and
away to free the headlight bulb.
8. Carefully remove the socket and bulb assembly by pulling it straight back.
Maintenance and Care
Owner Maintenance
8-39
MX-5_8X49-EA-07F_Edition5 Page321
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (322,1)
9. Remove the headlight bulb from thesocket.
10. Install the new socket and bulb
assembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
lWhen reinstalling the sealing cover, make
sure
faces up.
Front fog light bulbsí
1. If you are changing the right Front fog light bulb, start the engine, turn the
steering wheel all the way to the left,
and turn off the engine. If you are
changing the left Front fog light bulb,
turn the steering wheel to the right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise, and carefully pull it
backward.
8-40
Maintenance and Care
íSome models.
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page322
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (323,1)
5. Disconnect the socket and bulbassembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
6. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. If you are changing the right front turn signal light bulb, start the engine, turn
the steering wheel all the way to the
left, and turn off the engine. If you are
changing the left front turn signal light
bulb, turn the steering wheel to the
right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
MX-5_8X49-EA-07F_Edition5 Page323
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (324,1)
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse orderof removal.
Parking lights
1. Turn the socket and bulb assemblycounterclockwise and remove it.
2. Disconnect the bulb from the socket.
3. Install the new bulb in the reverse order of removal.
Front side-marker lights
NOTE
To replace the bulb, contact an Authorized
Mazda Dealer.
1. Slide the unit as shown in the figure toremove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
8-42
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page324
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (325,1)
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Pull the center section of the plasticretainers and remove them, then
remove the trunk end trim.
Removal
Installation
2. On the side the bulb is to be replaced, pull the center section of the plastic
retainers and remove them, then
remove the trunk side trim.
Removal
Installation
3. Turn the socket and bulb assembly counterclockwise and remove it. 4. Disconnect the bulb from the socket.
Brake lights/Taillights
Rear turn signal lights
Reverse lights
5. Install the new bulb in the reverse order of removal.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
License plate lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
MX-5_8X49-EA-07F_Edition5 Page325
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (326,1)
qReplacing Interior Light Bulbs
Overhead light
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the cover.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Trunk light
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
8-44
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page326
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (327,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work,
first inspect the fuses on the vehicle's left
side.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
3. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
Fuse puller
Fuse block cover
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Maintenance and Care
Owner Maintenance
8-45
MX-5_8X49-EA-07F_Edition5 Page327
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (328,1)
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
8-46
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page328
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (329,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FAN 30 A Cooling fan
2 FAN 7.5 A Cooling fan
3 DEFOG 20 A Rear window defroster
4 H/CLEAN ――
5 ROOM 15 A Overhead lights, Luggage compartment light, For protection of
various circuits
6 IG KEY2 15 A For protection of various circuits
7 HEATER 40 A Air conditioner
í
8 ABS 30 A ABS
9 FOG 15 A Front fog lightsí
10R.FOG ――
11 RHT L 30 A Power retractable hardtop (LH)í
12 RHT R 30 A Power retractable hardtop (RH)í
13MAG 7.5 A Air conditionerí
14ST 20 A Starter
15 TAIL 15 A Taillights, Parking lights, License plate lights, illuminations
16 ABS 40 A ABS
Maintenance and Care
Owner Maintenance
8-47íSome models.
MX-5_8X49-EA-07F_Edition5 Page329
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (330,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
17 BTN 30 A For protection of various circuits
18 MAIN 120 A For protection of all circuits
19 EGI INJ 10 A Injector
20 EGI COMP1 10 A Engine control system
21 EGI COMP2 10 A Engine control system
22 HEAD LOW L 15 A Headlight low beam (LH)
23 HEAD LOW R 15 A Headlight low beam (RH)
24 HEAD 15 A Headlight high beams
25 P.WIND 20 A Power windows
26 ENGINE 15 A Engine control system
27 WIPER 20 A Windshield wipers and washer
28 DRL 15 A DRL
í
29HORN 15 A Horn
30 STOP 10 A Brake lights
31 ETV 10 A Electric throttle valve
32 FUEL PUMP 15 A Fuel Pump
33 HAZARD 10 A Turn signals, Hazard warning flashers
34 P.WIND2 20 A Power windows
í
35 IG KEY140 A For protection of various circuits
8-48
Maintenance and Care
íSome models.
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page330
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F