lock MAZDA MODEL MX-5 MIATA POWER RETRACTABLE HARDTOP 2008 Manual PDF

Black plate (122,1)
13. Lift up the deck using two adults, oneon each side of the vehicle, and open
the deck completely.
CAUTION
ØLift the deck using two adults.
Doing it alone could result in
injury or the deck lid mechanism
being twisted which could damage
it.
Ø Do not let go of the deck lid on
both sides until it is fully open. The
deck lid could fall if it is released
too soon and cause injury.
Ø Do not attempt to forcefully lift the
deck. If the lock has not detached
and the deck is forcefully lifted, it
could damage the deck. Closing the hardtop
CAUTION
Ø
The procedure should be done by
at least two adults. Do not do it
alone so as not to cause injury or
vehicle damage.
Ø Some steps in the procedure
require holding your body in a
strained position for extended
periods and if over exerted it could
result in injury.
Ø Be very careful when closing the
hardtop to prevent pinching and
possible injury.
1. Grasp the hardtop along the side and front surfaces and lift it up enough to
create a clearance at the rear of
hardtop.
3-62
Knowing Your Mazda
Doors and Locks
MX-5_8X49-EA-07F_Edition5 Page122
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (123,1)
2. Grasp the hardtop along the side andrear surfaces and lift it up enough to
create a clearance behind the rear glass.
3. Grasp the hardtop along its side surfaceand the rear area of the rear glass, pull
the hardtop towards the front of the
vehicle, and completely close it.
4. Lock the top latch.Refer to Closing the Power Retractable
Hardtop on page 3-56. Closing the deck
1. Loop the center of the rope through the
pin on the link twice so that it does not
loosen.
Pin
Rope
Link
NOTE
Before closing the deck, two small ropes need
to be installed and tied into the trunk so that
the deck does not pop up while driving, and so
that the deck can be raised for servicing by an
Authorized Mazda Dealer.
2. Route one end of the rope to the insideof the vehicle passing it through the
gap in the trim. Route the other end to
the outside of the vehicle passing it
through the links.
To the inside of the vehicle
Trim
Rope
Knowing Your Mazda
Doors and Locks
3-63
MX-5_8X49-EA-07F_Edition5 Page123
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (124,1)
To the outside of the vehicle
Rope
Links
NOTE
Always route the one end of the rope to inside
of the vehicle. If it is not inside the vehicle, it
will be difficult to service the hardtop at an
Authorized Mazda Dealer.
3. Do the same procedure on the other
side.
4. Close the deck uniformly on both sides using two adults, one on each side of
the vehicle.
CAUTION
Close the deck using two adults.
Doing it alone could result in injury
or the deck lid mechanism being
twisted which could damage it. 5. Lightly pushing the deck downward,
pull the ropes to the rear along both
sides of the trunk to hold the deck
down.
NOTE
Pull the ropes horizontally to the vehicle rear.
Rope
6. Lightly move the deck and verify that it is secured completely.
7. Open the trunk using the key, and tie the rope to the bracket and knot it twice
so that it does not loosen.
Rope
Bracket
CAUTION
Tie the ropes securely so that the
deck does not open while the vehicle
is being driven.
3-64
Knowing Your Mazda
Doors and Locks
MX-5_8X49-EA-07F_Edition5 Page124
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (125,1)
NOTE
Open the trunk using the key. The remote
release button, advanced keyless entry
function, and the keyless entry system do not
operate when this emergency procedure is
done.
8. Tie off the other side rope the sameway.
9. Close the trunk lid.
After finishing the procedure
After finishing the procedure, have the
hardtop checked at an Authorized Mazda
Dealer as soon as possible.
WARNING
Drive the vehicle at a speed of 40 km/h
(25 mph) or lower before having the
hardtop checked at an Authorized
Mazda Dealer: The hardtop may open while the
vehicle is being driven and cause an
accident.
NOTE
The trunk cannot be opened with the remote
release button, advanced keyless entry
function, and the keyless entry system as they
are disabled when this emergency procedure is
done.
q Power Retractable Hardtop
Appearance Care
Refer to Hardtop Maintenance (page
8-55) for information on retractable
hardtop appearance care.
Knowing Your Mazda
Doors and Locks
3-65
MX-5_8X49-EA-07F_Edition5 Page125
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (126,1)
qWhen Warning Indicator/Beep is Activated
If an improper operation is performed or a system malfunction has occurred, the indicator light or a warning beep
is activated to notify the user of improper operation or a system malfunction.
Warning What to check
A warning beep sound is heard when the open or close
switch is pressed. Make sure that all the conditions for operating the
retractable hardtop have been met. If the chime sounds
despite having met all the operation conditions, consult
an Authorized Mazda Dealer to have the system
inspected.
A warning beep sound is heard when the open or close
switch is released. The hardtop is not fully opened or closed. Press the
switch until the open or close operation is completed.
A warning beep sound is heard continuously and the
indicator light is illuminated while the vehicle is driven. The hardtop has not completely opened or closed.
Continue to press the button until the operation is
completed. After the hardtop is completely closed, latch
the top latch.
If the open or close button has not been operated and
the operation indicator light is flashing: The system may have a malfunction. Have the vehicle
checked at an Authorized Mazda Dealer.
3-66
Knowing Your Mazda
Doors and Locks
MX-5_8X49-EA-07F_Edition5 Page126
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (128,1)
qOperation
Arming
The system is armed when the ignition
switch is turned from the ON position to
the ACC or LOCK position. The security
indicator light in the instrument cluster
flashes every 2 seconds until the system is
disarmed.
Disarming
The system is disarmed when the ignition
switch is turned to the ON position with
the registered advanced key.
The security indicator light illuminates for
about 3 seconds and goes out.
If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer. NOTE
lThe engine may not start and the security
indicator light may illuminate or flash if the
advanced key is placed in an area where it
is difficult for the system to detect the
signal, such as on the dashboard, or in the
glove box. Move the advanced key to
another place, turn the ignition switch to
the LOCK position, and then restart the
engine.
lSignals from a TV or radio station, or from
a transceiver or a mobile telephone could
interfere with your immobilizer system. If
you are using the proper advanced key and
the engine fails to start, check the security
indicator light. If the indicator light is
flashing, turn the ignition switch to the
ACC or LOCK position and wait for a
while, then restart the engine. If it doesn't
start after 3 or more tries, contact an
Authorized Mazda Dealer.
lIf the security indicator light flashes
continuously while you are driving, don't
shut off the engine. Go to an Authorized
Mazda Dealer and have it checked. If the
engine is shut off while the indicator light is
flashing, you won't be able to restart it.
lSince the electronic codes are reset when
repairing the immobilizer system, the
advanced key (including auxiliary key) are
needed. Bring all the advanced keys
(including auxiliary keys) to an Authorized
Mazda Dealer.
3-68
Knowing Your Mazda
Security System
MX-5_8X49-EA-07F_Edition5 Page128
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (132,1)
Theft-Deterrent Systemí
If the theft deterrent system detects an
inappropriate entry into the vehicle, which
could result in the vehicle or its contents
being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and flashing the hazard
warning lights.
Refer to Operation on page 3-72.
NOTE
lThe theft-deterrent system operates with the
key or the keyless entry system transmitter.
l(With advanced key)
The theft-deterrent system can also be
operated using a request switch or the start
knob.
The system operates only when the driver is
in the vehicle or within operational range
while the advanced key is being carried.
lThe system will not function unless it is
properly armed. To properly secure the
vehicle, always make sure both windows
are completely closed and both doors and
the trunk lid are locked before leaving the
vehicle. Remember to take your key and
transmitter.
qOperation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights flash for about 25
seconds when the system is triggered by
any one of the following:
lForcing open a door, the hood or the
trunk lid.
lUnlocking a door with the door lock
switch.
lOpening a door by operating an inside
door-lock knob.
lOpening the hood by operating the
hood release handle.
lOpening the trunk lid by operating the
trunk lid release button.
If the system is triggered again, the lights
and horn will activate until a door is
unlocked or the trunk lid is opened with
the key or with the transmitter.
(With advanced key)
The lights and horn can also be
deactivated by pressing a request switch.
q How to Arm the System
1. Remove the key from the ignition
switch.
(With advanced key)
Turn the start knob to the LOCK
position.
2. Make sure the hood and the trunk lid are closed. Close and lock both doors
from the outside using the key. If you
have the keyless entry system, press
the lock button on the transmitter.
(With advanced key)
Press a request switch on the doors or
the lock button on the transmitter.
The hazard warning lights will flash
once to indicate that the system is
armed.
(Without advanced key)
The following method will also arm the
theft-deterrent system:
Close the hood and the trunk lid . Press
the area on the door-lock switch
marked “LOCK ”once. Close both
doors.
NOTE
Locking the doors with the inside door-lock
knob will not arm the system.
3-72
Knowing Your Mazda
íSome models.
Security System
MX-5_8X49-EA-07F_Edition5 Page132
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (133,1)
qTo Turn off an Armed System
An armed system can be turned off by any
one of the following methods:
lUnlock a door with the key.lPress the unlock button on the keyless
entry system transmitter.
lInsert the key into the ignition switch
and turn it to the ON position.
l(With advanced key)lPress a request switch on the doors
or the unlock button on the
transmitter.
lTurn the start knob to the ON
position.
The hazard warning lights will flash twice
to indicate that the system is turned off.
NOTE
The trunk lid can be opened with the key or the
transmitter even when the system is armed. The
alarm will not come on and the system will
remain armed.
q To Stop an Alarm
A triggered alarm can be turned off by
any one of the following methods:
lUnlock a door with the key.lOpen the trunk lid with the key.lPress the unlock button or press and
hold the trunk button on the keyless
entry system transmitter.
l(With advanced key)lPress a request switch on the doors.lPress the unlock button or press and
hold the trunk button on the
transmitter.
NOTE
If you have any problem with the theft-
deterrent system, consult an Authorized Mazda
Dealer.
q Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove box.
Mazda recommends that you affix it to the
lower rear corner of a front door window.
Knowing Your Mazda
Security System
3-73
MX-5_8X49-EA-07F_Edition5 Page133
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (134,1)
Steering Wheel
WARNING
Never adjust the steering wheel while
the vehicle is moving:Adjusting the steering wheel while
the vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control
or an accident.
qTilt Steering Wheel
To change the angle of the steering wheel,
stop the vehicle, pull the tilt wheel release
lever under the steering column down,
adjust the wheel, then push the release
lever up to lock the column.
Tilt wheel release
lever
After adjusting, push the wheel up and
down to be certain it's locked before
driving.
Mirrors
qOutside Mirrors
Check the mirror angles before driving.
Mirror type
Flat type (driver's side)
Flat surface mirror.
Convex type (passenger side)
The mirror has single curvature on its
surface.
WARNING
Be sure to look over your shoulder
before changing lanes:
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears.
Power mirror
The ignition switch must be in the ACC
or ON position.
To adjust:
1. Press the left or right side of the
selector switch to choose the left or
right side mirror.
3-74
Knowing Your Mazda
Steering Wheel and Mirrors
MX-5_8X49-EA-07F_Edition5 Page134
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F

Black plate (135,1)
2. Depress the mirror switch in theappropriate direction.
Mirror switchSelector switch
Outside mirror
After adjusting the mirror, lock the control
by placing the selector switch in the
middle position.
Folding the mirror
Fold the outside mirror rearward until it is
flush with the vehicle.
WARNING
Always return the outside mirrors to
the driving position before you start
driving:
Driving with the outside mirrors
folded in is dangerous. Your rear view
will be restricted, and you could have
an accident.
qRearview Mirror
Rearview mirror adjustment
Before driving, adjust the rearview mirror
to center on the scene through the rear
window.
Reducing glare from headlights
Adjust the mirror with the day/night lever
in the day position.
Push the lever forward for day driving.
Pull it back to reduce glare from
headlights.
Night
Day Day/Night lever
Knowing Your Mazda
Steering Wheel and Mirrors
3-75
MX-5_8X49-EA-07F_Edition5 Page135
Thursday, February 21 2008 12:50 AM
Form No.8X49-EA-07F