automatic transmission MAZDA MODEL MX-5 RF 2017 (in English) Service Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL MX-5 RF, Model: MAZDA MODEL MX-5 RF 2017Pages: 609, PDF Size: 5.96 MB
Page 502 of 609
7–8
If Trouble Arises
Flat Tyre
NOTE
The tyre sealant cannot be reused.
Purchase new tyre sealant at an
Authorised Mazda Repairer.
The emergency À at tyre repair kit
cannot be used in the following
cases.
Consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
The period of effective use for
the tyre sealant has expired. (The
period of effectiveness is indicated
on the bottle label.)
The tear or puncture exceeds about
4 mm (0.16 in).
The damage has occurred to an
area of the tyre other than the
tread.
The vehicle has been driven with
nearly no air remaining in the tyre.
The tyre has come off the wheel
rim.
Damage to the wheel rim has
occurred.
The tyre has two or more
punctures.
Using the Emergency Flat Tyre
Repair Kit
1. Move the vehicle off the right-of-way
to a safe place on a level and hard
surface where the vehicle does not
obstruct traf ¿ c.
2. Shift the shift lever to the 1 or Reverse
(R) position for a manual transmission,
and shift the selector lever to the P
position for an automatic transmission.
3. Apply the parking brake with the brake
pedal depressed and turn off the engine. 4. If necessary, À ash the hazard warning
lights and set up the roadside
emergency triangle.
5. Unload passengers and cargo and
remove the emergency À at tyre repair
kit.
6. Shake the tyre sealant well.
CAUTION
If the bottle is shaken after the injection
hose is screwed on, tyre sealant could
spray out from the injection hose. Tyre
sealant contacting clothing or other
objects may be impossible to remove.
Shake the bottle before screwing on the
injection hose.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 508 of 609
7–14
If Trouble Arises
Flat Tyre
Changing a Tyre
WARNING
Be sure to follow the directions for
changing a tyre:
Changing a tyre is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure someone.
No person should place any portion
of their body under a vehicle that is
supported by a jack.
Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in
a vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a hard, level surface off the
right-of-way and ¿ rmly set the parking
brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning À asher.
4. Have everyone get out of the vehicle
and away from the vehicle and traf ¿ c.
5. Remove the jack and tool (page
7-5 ). 6. Block the wheel diagonally opposite
the tyre to be changed. When blocking
a wheel, place a tyre block both in front
and behind the tyre.
NOTE
When blocking a tyre, use rocks or
wood blocks of suf ¿ cient size if possible
to hold the tyre in place.
Removing a Tyre
1. Loosen the wheel nuts by turning them
anticlockwise one turn each, but do not
remove any wheel nuts until the tyre
has been raised off the ground.
2. Place the jack on the ground.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 517 of 609
7–23
If Trouble Arises
Emergency Starting
Starting a Flooded Engine
If the engine fails to start, it may be
À ooded (excessive fuel in the engine).
Follow this procedure:
1. If the engine does not start within
¿ ve seconds on the ¿ rst try, wait ten
seconds and try again.
2. Make sure the parking brake is on.
3. Depress the accelerator all the way and
hold it there.
4. Depress the clutch pedal (Manual
transmission) or the brake pedal
(Automatic transmission), then
press the push button start. If the
engine starts, release the accelerator
immediately because the engine will
suddenly rev up.
5. If the engine fails to start, crank it
without depressing the accelerator.
If the engine still does not start using
the previous procedure, have your
vehicle inspected by an expert repairer,
we recommend an Authorised Mazda
Repairer.
Push-Starting
Do not push-start your Mazda.
WARNING
Never tow a vehicle to start it:
Towing a vehicle to start it is
dangerous. The vehicle being towed
could surge forward when its engine
starts, causing the two vehicles to
collide. The occupants could be
injured.
CAUTION
Do not push-start a vehicle that has a
manual transmission. It can damage the
emission control system.
NOTE
You cannot start a vehicle with an
automatic transmission by pushing it.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 518 of 609
7–24
If Trouble Arises
Overheating
O v e r h e a t i n g
If the high engine coolant temperature
warning light turns on, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running inde ¿ nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and
radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the high engine coolant temperature
warning light turns on:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the bonnet and start the engine.
If neither coolant nor steam is
escaping:
Open the bonnet and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 522 of 609
7–28
If Trouble Arises
Emergency Towing
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
Shift to neutral (Manual
transmission), or the N position
(Automatic transmission).
Switch the ignition to ACC.
Release the parking brake.
Remember that power assist for the
brakes and steering will not be available
when the engine is not running.
Towing Hooks
CAUTION
The towing eyelet should be used
in an emergency (to get the vehicle
out of a ditch or a snow bank, for
example).
When using the towing eyelets,
always pull the lead or chain in a
straight direction with respect to the
eyelet. Never apply a sideways force.
NOTE
When towing with chain or lead, wrap
the chain or lead with a soft cloth near
the bumper to prevent damage to the
bumper.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 530 of 609
7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
Automatic
Transmission
Indication/Warning
Light
*
The indication/light illuminates when the transmission has a problem.
CAUTION
If the automatic transmission warning indication/light illuminates, the transmission has
an electrical problem. Continuing to drive your Mazda in this condition could cause
damage to your transmission. Consult an expert repairer, we recommend an Authorised
Mazda Repairer as soon as possible.
(Illuminate)
TCS/DSC Indicator
Light If the light stays on, the TCS, DSC or the brake assist system may have a malfunction and
they may not operate correctly. Take your vehicle to an expert repairer, we recommend an
Authorised Mazda Repairer.
Air Bag/Seat Belt
Pretensioner System
Warning Light A system malfunction is indicated if the warning light constantly À ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
Active Bonnet
Warning Light *
The light turns on when the ignition is switched on for an operation check, and turns off a
few seconds later.
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light does not turn on when the ignition is switched ON. Remains turned on/ À ashing.
WARNING
Do not drive the vehicle with the active bonnet warning light turned on or À ashing:
Driving the vehicle with the active bonnet warning light turned on or À ashing is
dangerous as the active bonnet mechanism may not activate normally and function
as intended in the event the vehicle were to contact a pedestrian.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 540 of 609
7–46
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Message Indicated in Multi-information Display *
I f t h e r e i s a n o t i ¿ cation from the vehicle, a message is displayed in the multi-information
display. Check the information and take the necessary action.
(Display example)
If the warning light turns on/ À ashes simultaneously or a symbol is indicated in the display,
check the information regarding the warning light or symbol. (page 4-42 )
Display Content Action to be taken
Indicated when the push button start is
pressed while the shift lever is not in
the P position. Shift the shift lever to the P position.
Indicated when a seat belt is
unfastened and the driver's door is
opened while the i-stop function is
operating. Press the push button start again
to start the engine. For automatic
transmission vehicles, shift the shift
lever to the P position before starting
the engine.)
Indicated when the push button start is
pressed without depressing the brake
pedal. Depress the brake pedal and press the
push button start.
Indicated when the push button start is
pressed without depressing the clutch
pedal. Depress the clutch pedal and press the
push button start.
Indicated while the steering wheel is
locked. Release the steering lock.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 546 of 609
7–52
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with the
door open or ajar, or the ignition is not
switched OFF with a key being carried,
a beep will be heard outside for about 2
seconds to notify the driver that the door
or boot lid cannot be locked.
Key Left-in-boot Compartment
Warning Beep (With the advanced
keyless function)
If the key is left in the boot with all the
doors locked and the boot lid closed, a
beep will be heard outside for about 10
seconds to notify the driver that the key is
in the boot. In this case, take out the key
by pressing the electric boot lid opener
and opening the boot lid. The key taken
out of the boot may not operate because its
functions have been temporarily stopped.
To restore the key's functions, perform the
applicable procedure (page 3-8 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If all the doors and boot are locked using
another key while the key is left in the
cabin, the beep which sounds outside of
the vehicle will be heard for about 10
seconds to notify the driver that the key
is in the cabin. In this case, take out the
key by opening the door. A key taken
out of the vehicle using this method may
not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-8 ).
Electronic Steering Lock Warning
Beep
The warning beep operates if the steering
wheel is not unlocked after the push button
start is pressed. (page 4-4 )
i-stop Warning Beep *
If the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver that
engine idling is stopped. It stops when
the driver's door is closed.
The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
(European model)
The driver's seat belt is unfastened and
the driver's door is opened.
(Except European model)
(Manual transmission)
With the shift lever in a position other
than neutral, the driver's seat belt is
unfastened and the driver's door is
opened.
(Automatic transmission)
With the selector lever in the D or
M (not in second gear ¿ xed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 556 of 609
7–62
If Trouble Arises
When the Roof Cannot be Closed
Manual closing
Before closing manually
WARNING
Verify that the ignition is switched off
before manually operating the roof:
Manually closing the roof with the
ignition not switched off is dangerous
as the motors could turn on suddenly
and cause injury resulting from
hands or ¿ ngers being pinched in the
mechanism.
1. Park on a hard, level surface off the
right-of-way and ¿ rmly set the parking
brake.
2. Put a vehicle with an
automatictransmission in Park (P), a
manual transmission in Neutral.
3. Switch the ignition off while depressing
the brake pedal.
4. Turn on the hazard warning À asher if it
is needed.
Tool preparation
Take out the ¿ ve tools stored in the seat
side box.
Refer to Seat Side Box on page 5-131 .
WireGear
(tool kit)Rope
L-shaped
hexagonal wrench
(Small)L-shaped
hexagonal wrench
(Large)
Opening the rear roof
CAUTION
When turning the bolt, cover the
front roof using a cloth. The front
roof may be damaged if the L-shaped
hexagonal wrench contacts it.
Because the clearance with the stored
front roof is narrow, be careful not
to let the L-shape hexagonal wrench
contact the roof when turning the
bolt.
NOTE
Moving the seats as far forward as
possible and folding the seatbacks
forward will facilitate the procedure.
Refer to Seat Operation on page 2-5 .
1. Remove the aerial if it is installed.
Refer to When the Aerial on page
5-14 .
2. Insert the short end of the L-shaped
hexagonal wrench (Large) into the
motor bracket bolt.
Bolt
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 591 of 609
9–5
Speci ¿ cations
Speci ¿ cations
Lubricant Quality
Lubricant Classi ¿ cation
Europe Except Europe
Engine oil
*1
Recommended Oils *2 Oil Quality
Mazda Original Oil Supra 0W-20
API SG/SH/SJ/SL/SM/SN or
ILSAC GF-II/GF-III/GF-IV/GF-V Mazda Original Oil Ultra 5W-30
Alternative Oil Quality
*3
API SL/SM/SN or
ACEA A3/A5 0W-20
5W-30
Coolant FL-22 type
Manual transmission oil Mazda Original Long Life Gear Oil IS
*4
Automatic transmission À uid JWS3309
Rear differential oil Mazda Long Life Hypoid Gear Oil SG1
Brake/Clutch À uid SAE J1703 or FMVSS116 DOT-3 or DOT-4
*1 Refer to Recommended Oil on page 6-17 .
Do not use oils which do not meet the above speci ¿ cation or requirements. Use of unsuitable oil may lead to
engine damage which is not covered by the Mazda Warranty.
*2 Mazda Original Oils are specially designed/tested for the respective engine. For optimum performance we
recommend to use Mazda Original Oils at all times.
*3 If you are unable to ¿ nd a Mazda Original Oil, alternative oils meeting the listed speci ¿ cation may also be used.
*4 Mazda Original Long Life Gear Oil IS is superior oil for optimum shift-feel. Using Mazda Original Long Life
Gear Oil IS is recommended.
If Mazda Original Long Life Gear Oil IS cannot be obtained, use standard oil (API Service GL-4 (SAE 75W-
90)). However, shifting in very low temperatures may become dif ¿ cult.
/ : A ( . ' ' , A ' F K V K Q P K P F D