ignition MAZDA MODEL RX 8 2007 (in English) Manual Online
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2007, Model line: MODEL RX 8, Model: MAZDA MODEL RX 8 2007Pages: 443
Page 292 of 443
Black plate (291,1)
Owner Maintenance Precautions
Improper or incomplete service may result in problems. This section gives instructions only
for items that are easy to perform.
As explained in the Introduction (page 8-2), several procedures can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you're unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
WARNING
Do not perform maintenance work if you lack sufficient knowledge and experience or
the proper tools and equipment to do the work. Have maintenance work done by a
qualified technician:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedures.
If you must run the engine while working under the hood, make certain that you
remove all jewelry (especially rings, bracelets, watches, and necklaces) and all
neckties, scarves, and similar loose clothing before getting near the engine or cooling
fan which may turn on unexpectedly:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Turn off the ignition switch and make sure the fan is not running before attempting to
work near the electrical cooling fan:
Working near the electrical cooling fan when it is running is dangerous. You could be
hit by the fan and seriously injured.
Maintenance and Care
Owner Maintenance
8-9
RX-8_8V89-EA-06F_Edition1 Page291
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 293 of 443
Black plate (292,1)
NOTE
Once the engine coolant exceeds a preset temperature, an electrical cooling fan turns on.
It will continue running for about 10 minutes after the ignition switch is turned to off.
8-10
Maintenance and Care
Owner Maintenance
RX-8_8V89-EA-06F_Edition1 Page292
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 297 of 443
Black plate (296,1)
5. Pull out the dipstick, wipe it clean, and
reinsert it fully.
Full
Low OK
6. Pull it out again and examine the level.
It's OK between L and F.
But if it's near or below L, add enough
oil to bring the level to F.
CAUTION
Don't add engine oil over F. This may
cause engine damage.
The distance between L and F on the
dipstick represents the following:
Oil capacity
L (US qt, Imp qt) 1.7 (1.8, 1.5)
NOTE
lEach mark from the F mark equates
to about 0.5 L (US 0.5 qt, Imp 0.4
qt).
There are 3 marks between L and F.
lVerify that the engine cover is
securely installed.
Engine Coolant
qInspecting Coolant Level
WARNING
Do not use a match or live flame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS
HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Turn the ignition switch off and
remove the key from the ignition
switch when inspecting the engine:
Working near the electrical cooling
fan when it is running is dangerous.
You could be hit by the fan and
seriously injured.
Do not remove the cooling
system cap when the engine and
radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
8-14
Maintenance and Care
Owner Maintenance
RX-8_8V89-EA-06F_Edition1 Page296
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 298 of 443
Black plate (297,1)
NOTE
Once the engine coolant exceeds a
preset temperature, an electrical cooling
fan turns on. It will continue running
for about 10 minutes after the ignition
switch is turned to off.
NOTE
Changing the coolant should be done
by an Authorized Mazda Dealer.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year―at the beginning of the
winter season―and before traveling
where temperatures may drop below
freezing.
Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the F and L marks
on the coolant reservoir when the engine
is cool.
If it's at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
CAUTION
lRadiator coolant will damage paint.
Rinse it off quickly if spilled.
lUse only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant's effectiveness.
lDon't add only water. Always add a
proper coolant mixture.
lThe engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
lDO NOT USE coolants Containing
Alcohol, methanol, Borate or
Silicate.
These coolants could damage the
cooling system.
lDO NOT MIX alcohol or methanol
with the coolant. This could damage
the cooling system.
lDon't use a solution that contains
more than 60% antifreeze.
This would reduce effectiveness.
Maintenance and Care
Owner Maintenance
8-15
RX-8_8V89-EA-06F_Edition1 Page297
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 313 of 443
Black plate (312,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement is
necessary.
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the
bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries could
be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
qReplacing a Headlight Bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood and find the high and low
beam bulbs in the rear of the headlight
unit.
The outboard bulb is the LOW beam,
and the inboard one is the HIGH beam.
Refer to Light Bulbs on page 8-29.
3. If you are changing the right headlight
bulb, start the engine, turn the steering
wheel all the way to the right, and turn
off engine. If you are changing the left
headlight bulb, turn the steering wheel
to the left.
4. Turn the center section of the plastic
retainer counterclockwise and remove
the retainers and partially peel back the
mudguard.
Removal
Installation
8-30
Maintenance and Care
Owner Maintenance
RX-8_8V89-EA-06F_Edition1 Page312
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 319 of 443
Black plate (318,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system doesn't work, first
inspect fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the fuse
puller provided on the inside of the
engine compartment fuse block cover.
4. Inspect the fuse and replace it if it's
blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an expert
repairer install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
8-36
Maintenance and Care
Owner Maintenance
RX-8_8V89-EA-06F_Edition1 Page318
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 320 of 443
Black plate (319,1)
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
Next to air filter
Engine cover
Near battery
Batter
y cover
NOTE
Remove the engine and battery covers
before removing the fuse block cover
near the battery.
3. If any fuse but the MAIN fuse is
blown, replace it with a new oneof the
same amperage rating.
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is a
high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
NOTE
Verify that the engine cover is securely
installed.
Maintenance and Care
Owner Maintenance
8-37
RX-8_8V89-EA-06F_Edition1 Page319
Friday, May 19 2006 9:52 AM
Form No.8V89-EA-06F
Page 381 of 443
Black plate (380,1)
A
Accessory Socket .............................. 6-54
Add-On Non-Genuine Parts and
Accessories ....................................... 9-13
Advanced Key ..................................... 3-2
Advanced key maintenance ......... 3-5
Advanced key suspend
function ...................................... 3-17
Auxiliary key .............................. 3-16
Locking, unlocking with request
switch ........................................... 3-8
Opening the trunk lid with request
switch ......................................... 3-10
Operational range ......................... 3-7
Remote control function ............. 3-14
Service ......................................... 3-6
Air Bag Systems ............................... 2-32
Ambient Temperature Display .......... 6-47
Antenna ............................................. 6-10
Anti-Lock Brake System (ABS) ......... 5-7
Warning light ............................... 5-7
Appearance Care ............................... 8-41
Ashtray .............................................. 6-49
Audio System ................................... 6-10
Audio control switch .................. 6-40
Audio set .................................... 6-21
Operating tips for audio
system ........................................ 6-10
Safety certification ..................... 6-43
Automatic Transmission
Driving tips ................................ 5-18
Manual shift mode ..................... 5-13
Shift-lock system ....................... 5-13
Transmission ranges ................... 5-12
B
Battery
Emergency starting .................... 7-20
Maintenance ............................... 8-21
Specifications ............................. 10-4
Beep Sounds
Engine overrev warning beep .... 5-54
Ignition key reminder ................. 5-53
Lights-on reminder ..................... 5-53
Seat belt warning beep ............... 5-53
Tire inflation pressure warning
beep ............................................ 5-54
Before Starting the Engine .................. 4-6
After getting in ............................. 4-6
Before getting in .......................... 4-6
Body Lubrication .............................. 8-18
Brake/Clutch
Fluid ........................................... 8-16
Brakes
Anti-lock brake system (ABS) ..... 5-7
Foot brake .................................... 5-5
Pad wear indicator ........................ 5-8
Parking brake ............................... 5-5
Warning light ............................... 5-6
Break-In Period ................................... 4-7
Bulb Replacement ............................. 8-29
C
Capacities .......................................... 10-5
Carbon Monoxide ............................... 4-5
Catalytic Converter ............................. 4-4
Cell Phones ....................................... 9-14
Center Console .................................. 6-52
11-2
Index
RX-8_8V89-EA-06F_Edition1 Page380
Friday, May 19 2006 9:53 AM
Form No.8V89-EA-06F
Page 383 of 443
Black plate (382,1)
F
Front Seats
(Manually Operated Seats) ................. 2-2
Fuel
Filler lid and cap ........................ 3-40
Gauge ......................................... 5-37
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-36
Panel description ........................ 8-38
Replacement ............................... 8-36
G
Gauges .............................................. 5-33
Glove Box ......................................... 6-51
H
Hazard Warning Flasher .................... 5-62
Hazardous Driving .............................. 4-8
Headlight Washer .............................. 5-60
Headlights
Control ....................................... 5-55
Flashing ...................................... 5-56
High-low beam .......................... 5-56
Leveling ..................................... 5-56
On reminder ............................... 5-55
HomeLink Wireless Control
System .............................................. 5-62
Hood Release .................................... 3-42
Horn .................................................. 5-61
I
Ignition
Keys ........................................... 3-22
Switch .......................................... 5-2
Illuminated Entry System ................. 6-44
I
Immobilizer System
(with Advanced Key) ........................ 3-45
Immobilizer System
(without Advanced Key) ................... 3-48
Indicator Lights ................................. 5-39
Cruise ......................................... 5-51
DSC OFF .................................... 5-51
Headlight auto-leveling
malfunction ................................ 5-52
Headlight high-beam .................. 5-50
power steering malfunction ........ 5-52
Security ...................................... 5-50
Shift position .............................. 5-50
TCS/DSC ................................... 5-51
Turn-signal/hazard warning ....... 5-52
Information Display .......................... 6-46
Ambient temperature display ..... 6-47
Audio display ............................. 6-48
Climate control display .............. 6-48
Clock .......................................... 6-47
Information display functions .... 6-46
Inside Trunk Release Lever ............... 3-36
Instrument Cluster ............................. 5-33
Interior Care ...................................... 8-46
Interior Lights ................................... 6-44
J
Jump-Starting .................................... 7-21
K
Keyless Entry System ....................... 3-23
Keys .................................................. 3-22
L
Label Information ............................. 10-2
11-4
Index
RX-8_8V89-EA-06F_Edition1 Page382
Friday, May 19 2006 9:53 AM
Form No.8V89-EA-06F
Page 399 of 443
12
RoutingAddress
Book
Getting started
Activation
Insert the map disc into the unit to start the Mobile Navigation System.
Note
lThe map disc cannot be inserted or ejected while the ignition switch is in the OFF position.
lRemember that the battery can run down if the ignition switch is kept in the ON or ACC
position for a long time while the engine not running.
nMap Disc
lRefer to “Handling and Care of Map Discs” to know how to handle a map
disc (
page 56).
1
Turn the ignition switch
to the ON position and
press to open
the display.Note
lThis display angle can be adjusted by pressing .
When the is
pressed, the display
angle changes in
stages.
lPress to close the display.
2
Insert the map disc
with the printed side
facing up.Note
lThe main unit is located in the Center Console (Rear).lCondensation may form on the optical lens or the
map disc inside the unit when the temperature in
the vehicle increases in a short time such as when
heating the car on a cold day. This condensation
may cause malfunctions. If so, unload the map disc
and do not operate the unit for approximately 1
hour. Wipe the condensation off the map disc with a
soft cloth.
If the unit does not operate correctly after 1 hour,
consult an Authorized Mazda Dealer.
Cautions
OPENTILT
TILT
OPEN
(CAUTION) screen
<0034003a000f001a0041003000230038002b0041002700230010004400510051004d00020002003200430049004700020013001400020002002f0051005000460043005b000e0002002f0043005b000200130017000e000200140012001200180002000200
14001c0016001500020032002f>