trunk MAZDA MODEL RX 8 2008 (in English) Owner's Manual

Black plate (108,1)
Theft-Deterrent Systemí
If the theft deterrent system detects an
inappropriate entry into the vehicle, which
could result in the vehicle or its contents
being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and flashing the hazard
warning lights.
Refer to Operation on page 3-46.
NOTE
lThe theft-deterrent system operates with the
key or the keyless entry system transmitter.
l(With advanced key)
The theft-deterrent system can also be
operated using a request switch or the start
knob.
The system operates only when the driver is
in the vehicle or within operational range
while the advanced key is being carried.
lThe system will not function unless it is
properly armed. To properly secure the
vehicle, always make sure all windows are
completely closed and all doors and the
trunk lid are locked before leaving the
vehicle. Remember to take your key and
transmitter.
qOperation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights flash for about 3
minutes when the system is triggered by
any one of the following:
lForcing open a door, the hood or the
trunk lid.
lUnlocking a door with the inside door-
lock knob.
lUnlocking a door with the door lock
switch.
lOpening the hood by operating the
hood release handle.
lOpening the trunk lid by operating the
trunk lid release button.
If the system is triggered again, the lights
and horn will activate until a door is
unlocked or the trunk lid is opened with
the key or with the transmitter.
(With advanced key)
The lights and horn can also be
deactivated by pressing a request switch.
q How to Arm the System
1. Remove the key from the ignition
switch.
(With advanced key)
Turn the start knob to the LOCK
position.
2. Make sure the hood and the trunk lid are closed. Close and lock all doors
from the outside using the key or press
the lock button on your keyless entry
system transmitter.
(With advanced key)
Press a request switch or the lock
button on the transmitter.
The hazard warning lights will flash
once to indicate that the system is
armed.
(Without advanced key)
The following method will also arm the
theft-deterrent system:
Close the hood and the trunk lid . Press
the area on the door-lock switch
marked “LOCK ”once. Close all doors.
NOTE
Locking the doors with the inside door-lock
knob will not arm the system.
3-46
Knowing Your Mazda
íSome models.
Security System
RX-8_8X44-EA-07G_Edition1 Page108
Friday, May 11 2007 5:3 PM
Form No.8X44-EA-07G

Black plate (109,1)
qTo Turn off an Armed System
An armed system can be turned off by any
one of the following methods:
lUnlock a door with the key.lPress the unlock button on the keyless
entry system transmitter.
lInsert the key into the ignition switch
and turn it to the ON position.
l(With advanced key)lPress a request switch or the unlock
button on the transmitter.
lTurn the start knob to the ON
position.
The hazard warning lights will flash twice
to indicate that the system is turned off.
NOTE
The trunk lid can be opened with the key or the
transmitter even when the system is armed. The
alarm will not come on and the system will
remain armed.
q To Stop an Alarm
A triggered alarm can be turned off by
any one of the following methods:
lUnlock a door with the key.lOpen the trunk lid with the key.lPress the unlock button or press and
hold the trunk button on the keyless
entry system transmitter.
l(With advanced key)lPress a request switch.lPress the unlock button or press and
hold the trunk button on the
transmitter.
NOTE
If you have any problem with the theft-
deterrent system, consult an Authorized Mazda
Dealer.
q Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove box.
Mazda recommends that you affix it to the
lower rear corner of a front door window.
Knowing Your Mazda
Security System
3-47
RX-8_8X44-EA-07G_Edition1 Page109
Friday, May 11 2007 5:3 PM
Form No.8X44-EA-07G

Black plate (242,1)
To open, squeeze the latch and pull the lid
down.
When closing the storage box, put the
storage box back in its original position
until you hear a click sound.
NOTE
When using the storage box to store heavy
accessories, remove the storage box before
placing or removing the accessories.
Insert the key (auxiliary key*) and turn it
clockwise to lock, counterclockwise to
unlock.
* Advanced key equipped vehicle
Lock
Unlock
Loading long objects with storage box
removed
The storage box can be removed for
convenient loading of long objects such as
skis placed through the trunk.
WARNING
Secure long objects in the trunk so that
they cannot be thrown forward in the
cabin and avoid sudden breaking or
maneuvering:
Sudden braking or maneuvering
while long objects are loaded
through the removed storage box
area and into the trunk is dangerous.
Operation of the shift/selector lever
could be obstructed resulting in a
serious accident.
6-52
Interior Comfort
Interior Equipment
RX-8_8X44-EA-07G_Edition1 Page242
Friday, May 11 2007 5:4 PM
Form No.8X44-EA-07G

Black plate (254,1)
WARNING
Never operate the compressor above
300 kPa (3.1 kgf/cm2, 3 bar, 43.5 psi):
Operating the compressor above 300
kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi) is
dangerous. When the inflation
pressure rises above 300 kPa (3.1
kgf/cm
2, 3 bar, 43.5 psi), heated air
will be exhausted from the back of
the compressor and you could be
burned.
CAUTION
If the compressor operates slowly or
becomes hot, it indicates
overheating. Turn the compressor off
immediately and leave it turned off
for 30 minutes or longer.
NOTE
lCheck the tire inflation pressure label (rear
door on the driver's side) for the correct tire
inflation pressure.
lDo not use the compressor for longer than
10 minutes because using the compressor
for long periods could damage it.
lIf the tire does not inflate, repair of the tire
may not be possible. If the tire does not
reach the correct inflation pressure within a
10-minute period, it probably has received
more extensive damage. When this happens,
the emergency flat tire repair kit cannot be
used to repair the tire. Contact an
Authorized Mazda Dealer.
lIf the tire has been over-inflated, loosen the
screw cap on the compressor and bleed
some of the air out.
17. When the tire has been inflated to the proper inflation pressure, turn the
compressor switch off and remove the
compressor hose from the tire valve. 18. Install the tire valve cap.
19. Put the emergency flat tire repair kit
in the trunk and continue driving.
CAUTION
ØDrive carefully to an Authorized
Mazda Dealer and keep the
vehicle speed below 80 km/h (50
mph).
Ø If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With Tire Pressure Monitoring System)
If the tire is not properly inflated, the tire
pressure monitoring system warning light will
illuminate (page 5-28).
20. After driving the vehicle for 10 minutes or 5 km (3 miles), check the
tire pressure with the tire pressure
gauge equipped with the compressor.
If the tire pressure has fallen below
the correct tire pressure, inflate the
tire to the correct pressure again
following the steps from number 15.
CAUTION
ØIf the tire inflation pressure falls
below 130 kPa (1.3 kgf/cm2or bar,
18.9 psi), repair cannot be done
with the repair kit. Park the
vehicle on a level surface off the
right-of-way and contact an
Authorized Mazda Dealer.
Ø If the tire inflation pressure
continues to remain low after
repeating steps 14 to 21, park the
vehicle on a level surface off the
right-of-way and contact an
Authorized Mazda Dealer.
7-10
In Case of an Emergency
Flat Tire
RX-8_8X44-EA-07G_Edition1 Page254
Friday, May 11 2007 5:4 PM
Form No.8X44-EA-07G

Black plate (268,1)
Tiedown Hooks
CAUTION
Don't use the tiedown hooks under
the front and rear for towing.
They are designed ONLY for tying
down the vehicle when it's being
transported. Using them for towing
will damage the bumper.
qTiedown Hooks
1. Remove the tiedown eyelet and the lug
wrench from the trunk (page 7-3).
2. Wrap the lug wrench with a soft cloth to prevent damage to the bumper and
open the cap located on the front and
rear bumper.
Front
Rear
CAUTION
The cap cannot be completely
removed. Do not use excessive force
as it may damage the cap or scratch
the painted bumper surface.
3. Securely install the tiedown eyelet using the lug wrench.
Front
Rear
7-24
In Case of an Emergency
Emergency Towing
RX-8_8X44-EA-07G_Edition1 Page268
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G

Black plate (297,1)
Light Bulbs
Headlights (High-beam)Front side-marker lights
Front turn signal lights
Headlights (Low-beam)
Fog lights
Parking lights Overhead light/Map lights (Front)
Vanity mirror lights
Courtesy lights
Overhead light (Rear)
Trunk light
High-mount brake light
License plate light
Brake lights/Taillights
Reverse lights
Rear side-marker lights
Rear turn signal lights
Some models.
Maintenance and Care
Owner Maintenance
8-27
RX-8_8X44-EA-07G_Edition1 Page297
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G

Black plate (302,1)
Vanity mirror lightsEdge
3. Install the new bulb in the reverse orderof removal.
Trunk light
1. Press both sides of the lens cap toremove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
qReplacing a Bulb (Rear)
Rear turn signal lights, Brake lights/
Taillights, Reverse lights
1. Pull the center section of the plastic
retainer and remove the retainers and
partially open the trunk side trim.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Brake lights/Taillights Rear turn signal lights
Reverse lights
4. Install the new bulb in the reverse order of removal.
Rear side-marker lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
8-32
Maintenance and Care
Owner Maintenance
RX-8_8X44-EA-07G_Edition1 Page302
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G

Black plate (303,1)
High-mount brake light
1. Turn the center section of the plasticretainer counterclockwise and remove
the retainers and trunk rear trim.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
License plate light
1. Press the front of the lens to detach the
front tabs. 2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
3. Disconnect the bulb by pulling it out.
Edge
4. Install the new bulb in the reverse order of removal.
Maintenance and Care
Owner Maintenance
8-33
RX-8_8X44-EA-07G_Edition1 Page303
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G

Black plate (364,1)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R (SAE)
Headlights High beam
65H9 (―)
Low beam Halogen
55H7 (―)
Xenon fusion 35D2S (―)
Front turn signal lights 21WY21W (―)
Parking lights 5W5W (―)
Fog lights
í55 H11 (―)
Front side-marker lights 3.8―(#194)
High-mount brake light 21W21W (#7440)
Rear turn signal lights 21WY21W (―)
Brake lights/Taillights 21/5 W21/5W (#7743)
Reverse lights 21W21W (#7440)
License plate lights 5W5W (―)
Rear side-marker lights 0.57―(― )
The rear side-marker light bulbs cannot be replaced because they are an LED-type bulb.
The rear combination component must be replaced.
Interior light
Light bulb Category
Wattage ECE R
Trunk light 5W5W
Overhead light/Map lights (Front) 5W5W
Overhead light (Rear) 10―
Courtesy lights 5W5W
Vanity mirror lights 2―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally fitted to
your vehicle. For details, contact an Authorized Mazda Dealer.
10-6íSome models.
Specifications
RX-8_8X44-EA-07G_Edition1 Page364
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G

Black plate (368,1)
A
Accessory Socket .............................. 6-53
Add-On Non-Genuine Parts and
Accessories ....................................... 9-13
Advanced Key ..................................... 3-2Advanced key maintenance ......... 3-5
Advanced key suspend
function ...................................... 3-16
Auxiliary key .............................. 3-15
Locking, unlocking with request
switch ........................................... 3-8
Opening the trunk lid with request
switch ........................................... 3-9
Operational range ......................... 3-7
Remote control function ............. 3-13
Service ......................................... 3-6
Air Bag Systems ............................... 2-33
Ambient Temperature Display .......... 6-46
Antenna ............................................. 6-10
Anti-Lock Brake System (ABS) ......... 5-8 Warning light ............................... 5-8
Appearance Care ............................... 8-39
Ashtray .............................................. 6-48
Audio System ................................... 6-10 Audio control switch .................. 6-40
Audio set .................................... 6-21
Operating tips for audio
system ........................................ 6-10
Safety certification ..................... 6-42
Automatic Transmission Driving tips ................................ 5-18
Manual shift mode ..................... 5-14
Shift-lock system ....................... 5-14
Transmission ranges ................... 5-13
B
BatteryEmergency starting .................... 7-18
Maintenance ............................... 8-20
Specifications ............................. 10-4
Beep Sounds Engine overrev warning beep .... 5-53
Ignition key reminder ................. 5-53
Lights-on reminder ..................... 5-53
Seat belt warning beep ............... 5-53
Tire inflation pressure warning
beep ............................................ 5-54
Before Starting the Engine .................. 4-5 After getting in ............................. 4-5
Before getting in .......................... 4-5
Body Lubrication .............................. 8-17
Brake/Clutch Fluid ........................................... 8-15
Brakes Anti-lock brake system (ABS) ..... 5-8
Foot brake .................................... 5-5
Pad wear indicator ........................ 5-9
Parking brake ............................... 5-6
Warning light ............................... 5-7
Break-In Period ................................... 4-6
Bulb Replacement ............................. 8-27
C
Capacities .......................................... 10-5
Carbon Monoxide ............................... 4-4
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-14
Center Console .................................. 6-51
11-2
Index
RX-8_8X44-EA-07G_Edition1 Page368
Friday, May 11 2007 5:5 PM
Form No.8X44-EA-07G