buttons MAZDA MODEL SPEED MX-5 MIATA 2004 Owners Manual

3-4
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L

TransmitterLock button
To lock the doors, press the LOCK button
and the hazard warning lights will flash
once.
To confirm that all the doors have been
locked, press the LOCK button again
within 5 seconds. If they are closed and
locked, the horn will sound and the hazard
warning lights will flash once.
Unlock button
To unlock the driver
’s door, press the
UNLOCK button and the hazard warning
lights will flash twice.
To unlock all the doors, press the
UNLOCK button again within 5 seconds
and the hazard warning lights will flash
twice.
Trunk button
To open the trunk, press the button.
NOTE
•(U.S.A.)

This device complies with part 15
of the FCC Rules. Operation is
subject to the following two
conditions: (1) This device may not
cause harmful interference, and (2)
this device must accept any
interference received, including
interference that may cause
undesired operation.
• (CANADA)

This device complies with RSS-210
of Industry CANADA. Operation is
subject to the following two
conditions: (1) this device may not
cause interference, and (2) this
device must accept any interference,
including interference that may
cause undesired operation of the
device.
NOTE
If the LOCK and UNLOCK buttons
are pressed sequentially, the hazard
warning lights may not flash correctly.
Panic button Lock button
Trunk button Unlock button
NOTE
Confirm that all the doors are locked
visually or audibly by use of the
double click.
NOTE
After unlocking with the transmitter,
all doors will automatically lock if one
of the doors is not opened within about
30 seconds.
J07S_8T02-EA-03L_Edition1.book Page 4 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-6
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
Replacing the transmitter battery
1. Insert a small screwdriver into the slot and gently pry open the transmitter.
2. Press the portion of the battery indicated by A and remove the battery. 3. Install a new battery (CR2025 or
equivalent) into the front portion of the
holder with the positive pole ( )
facing up. Press on the B portion of the
battery to set the battery.
4. Align the front and back covers and snap the transmitter shut.
Slot
Back cover
A
Do not press any buttons when
replacing the battery. The electronic
code could be altered and cause the
keyless entry system to malfunction.
If the keyless entry system fails to
operate, contact an Authorized Mazda
Dealer.
B Back cover
Front
cover Front o
f
holder
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 6 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-20
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
5. Push the unlock buttons and fully release the top latches.
6. Lift up on the front section of the top to release it from the windshield header. 7. Fold back the front and carefully lower
it to the storage area, then put the
latches in the locked position.

Covering the Convertible Top
1. Cover the convertible top with the top
covering, stored in the trunk.
2. Feed the straps on the bottom of the covering through the lower links and
snap them into position.
3. Secure the top covering with the straps.
4. Affix the top covering fasteners.
Unlock button Top latch
Windshield header
Top covering
Link Strap
J07S_8T02-EA-03L_Edition1.book Page 20 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-21
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
5. Insert the top covering’s rear edge into
the groove in the body molding.

Raising the Convertible Top
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Undo the fasteners and straps. 5. Remove the top covering and store it
properly in the trunk.
6. Unlock the top latches and open them fully.
7. Hold the top lift handle and pull the top up and forward until it ’s against the
windshield header.
8. After securely hooking the top latches onto the windshield header, push each
latch up with the palm of your hand
until the lock buttons click and the
latches are locked.
Never drive with the top partially
folded or uncovered. Otherwise the top
and/or the top covering could be
damaged.
Top covering
Body
Molding
CAUTION
Sunvisor Sunvisor
Windshield header
J07S_8T02-EA-03L_Edition1.book Page 21 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-24
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
•When removing the hardtop, make sure
the operation is performed by 2
persons.
• Before removing or installing the
hardtop, be sure you are parked out of
traffic in a flat area near the location
your top is to be stored.
• When removing the hardtop, make sure
objects inside the vehicle aren
’t blown
away by the wind.
• Secure all loose objects inside before
driving with the hardtop removed.
• Don
’t drive through an automatic car
wash; it may damage the hardtop.
• Don
’t remove or install the hardtop
when the wind is strong; the wind
could damage the hardtop.
• Before removing the hardtop, lower the
antenna.
• Removing the hardtop while it
’s wet
can cause water to drip into the
passenger compartment.

Removing the Detachable
Hardtop
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Push the unlock buttons and fully release the top latches.Fastening Mechanisms:
It is dangerous to place your hands or
fingers near the fastening
mechanisms. Your hands or fingers
could be caught and injured by the
mechanism. Always keep your hands
and fingers away from the fastening
mechanisms when moving the top.
WARNING
Sunvisor Sunvisor
Unlock button
Top latch
J07S_8T02-EA-03L_Edition1.book Page 24 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-25
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
5. Push the unlock buttons and fully release the side latches.
6. Disconnect the rear window defroster coupler. 7. Slide the hardtop rearward while
pressing down on the rear deck latches
to unlock the latches.
8. Lift the hardtop straight off the body to prevent damage to the rear deck latches
and studs.
Unlock button
Side latch
Rear window defroster coupler
Windshield ’s Edges:
Not being careful of the windshield ’s
edges when getting into or out of the
vehicle is dangerous. The
windshield ’s edges could scratch and
cause injuries.
Be careful of the windshield ’s edges
when getting into or out of the
vehicle.
Rear deck latch
Hardtop
Rear deck stud
WARNING
J07S_8T02-EA-03L_Edition1.book Page 25 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-28
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
7. Push each top latch up with the palm of your hand until the lock buttons click
and the latches are locked.
8. Push each side latch down with the palm of your hand until the lock
buttons click and the latches are
locked. 9. Reconnect the rear window defroster
coupler.

Detachable Hardtop Appearance
Care
Refer to detachable hardtop maintenance
(page 8-46) for information on detachable
hardtop appearance care.
After installation, verify that all latches
are secure. Operating the vehicle with
unlocked latches may cause hardtop
damage or loss.
Side latch
CAUTION
NOTE
If the top rattles even when all latches
are secure, drive slowly and contact an
Authorized Mazda Dealer for
inspection.
Rear window defroster coupler
J07S_8T02-EA-03L_Edition1.book Page 28 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-24
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the Radio
Radio ON
Press a band selector button ( ) to
turn the radio on.
Band selection
Successively pressing the band selector
button ( ) switches the bands as
follows: FM1
→FM2
→AM.
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Band selector button
Satellite button*
Display
Channel preset buttons Scan button
Auto memory
button/Electric
serial number
button*
Manual tuning dial
Seek tuning
button
*For reception of optional Sirius digital satellite radio.
Used on vehicles equipped with the separately sold Sirius digital satellite radio\
unit.
For information on use, read the manual accompanying the Sirius unit.
Subscription of Sirius digital satellite radio service is available in the U.S. (Except Alaska and Hawaii).
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J07S_8T02-EA-03L_Edition1.book Page 24 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-32
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number, the track number and
the elapsed play back time for the current
track will be displayed.
Display CD slot
Disc-in indicator
CD ejectbutton
CD play button
Random button
Repeat button
Disc up button Scan
button
Fast-forward
button
Reverse button
Track up
button
Track down
button
Disc down
button
Load button
Power/Volume dial
Channel preset buttons
NOTE
•When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed
play back time, turn the audio
control dial to the right. Turn the
dial to the left to return to the
previous display.
• A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this
waiting time. Simultaneously
pressing the power/volume dial and
the load button ( ) for about 2
seconds will turn this beeping sound
ON or OFF.
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 32 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-38
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Antitheft System*
To deter theft of your vehicle
’s audio unit,
it has an integrated antitheft system. The
system is designed to accept a code
number that makes the unit inoperable if it
is stolen.
This system will be activated if the power
source is ever disconnected from or in any
way interrupted to the audio unit. When
the system is activated, the audio system
will not operate when reconnected to a
power supply, and "CODE" will flash on
the display until the correct code number
is input. If the antitheft system is
activated, reset the unit.
Display
Auto memory
button
Channel preset buttons
Antitheft indicator light
Read and understand all code setting
procedures before attempting to input
your personal code number.
The personal code number is only
shown on the audio unit display while
it is being set. Once it is input and
stored by the unit, it is never again
displayed. For that reason, be very
careful to immediately record your
personal code number, and never let an
unauthorized person set a code.
NOTE
Although the audio unit is operable
without the code number being set, we
recommend that you set your personal
code number.
CAUTION
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 38 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI